RUPTELA FM-Eco4 light T User manual

www.ruptela.com [e-mail] | [phone]
FM-Eco4 T
Quick Start Guide
Q
FM-Eco4+ T
FM-Eco4+ E T
FM-Eco4+ 3G T
FM-Eco4+ 3G E T
Make sure that you have:
•A computer with Windows 7/8/10
•An internet connection (or a predownloaded Device Center)
•A USB A to USB mini (Type B) cable
•Tools for installation and wire connection: a “+” type screwdriver, a panel removing tool, a wrench, a crimp
terminal, zip-ties (or double-sided tape)
Device overview
12 Pin cable
GNSS antenna cable (if applicable)
Indication LEDs
Indication LED patterns
LED
Pattern
Description
GNSS
Once every second
Accurate signal
Once every 0.4 seconds
No signal
GSM
Once every 4 seconds
Accurate signal
Once every 0.2 seconds
No signal
Always on
Link with the
server is open
1-Wire
Always off
No devices
connected
Once every 5 seconds
One device
connected
Twice every 5 seconds
Two devices
connected
Three times every 5
seconds
Three devices
connected
All
Once every 5 seconds
Sleep/deep
sleep mode
Device pinout
Pin
Wire color
Description
+BAT
Red
Power supply
6/12/24V
GND
Black
Ground
connection
DIN1
Pink
Digital input 1
DIN2
Blue
Digital input 2
DIN3
White
Digital input 3
DIN4
Yellow
Digital input 4
AIN1
Grey
Analog input 1
AIN2
Green
Analog input 2
DOUT1
Purple
Digital output 1
DOUT2
Orange
Digital output 2
1-Wire PWR
White/Red
1-Wire power
1-Wire DATA
Green/Yellow
1-Wire data

www.ruptela.com [email protected] | [phone]
Configuration
Unscrew the 6 screws.
Use a “+” type screwdriver.
Insert your SIM card.
Put on the top on and screw in the screws.
Download and launch the Device Center.
Install device drivers if prompted.
Click Configure device in the main menu.
Connect the device to your computer using a
USB cable.
Click Connect device.
Select your device.
Insert SIM
Unscrew
Screw in

www.ruptela.com [email protected] | [phone]
Open the Connection settings.
Configure Fleet Management System Main Server settings (TrustTrack server settings are entered by
default).
Configure network provider APN settings.
Click Save to device to upload the configuration to the device.
Installation
For faster and easier installation, it is highly recommended to use Power harness.
Install the device, make sure the label is facing towards the sky and is not covered by metal.
Follow the recommendations:
•It is allowed to tilt up to 45 degrees in any axis, but the top surface in all cases must be facing up
•Install behind the dashboard
•Install as close to the windshield as possible
•Avoid installing near metal surfaces
Fasten the device in the vehicle using zip-ties or double-sided tape.
Make sure it is secured tightly.
Install the GNSS antenna facing towards the sky (if applicable)
Connect the device according to the wiring diagram (on Page 4).
Turn on the ignition.
Check that the required data is received before finishing the installation.

www.ruptela.com [email protected] | [phone]
Wiring diagram
•Power input: 6/12/24 V DC
•Recommended protection fuse: 1 A
Further reading
•Documentation website: https://doc.ruptela.lt/
•Datasheet: https://doc.ruptela.lt/pages/viewpage.action?pageId=33357966
•User manual: https://doc.ruptela.lt/pages/viewpage.action?pageId=33357966
•Device Center: https://doc.ruptela.lt/display/AB/Device+Center
•Power harness Datasheet and Quick Start guide: https://doc.ruptela.lt/display/AB/Harnesses
•Installation using Fuse Tap Harness: https://www.youtube.com/watch?v=G_-tcJmsOVI
We highly recommend you read the user manual before using the device.
Legal information
Copyright © 2020 Ruptela. All rights reserved. Reproduction, transfer, distribution or storage of parts or all of the
contents in this document in any form without the prior written permission of Ruptela is prohibited. Other products
and company names mentioned in this document are trademarks or trade names of their respective owners.