Russell Hobbs RHCM50 Installation guide

1
INSTRUCTIONS AND WARRANTY
MODEL NO. RHCM50
VIVAĆE CAPSULE COFFEE MAKER
WITH MILK FROTHER

2
Congratulations on purchasing our Russell Hobbs Vivaće Capsule Coffee Maker with Milk Frother.
Each unit is manufactured to ensure safety and reliability. Before using this appliance for the first
time, please read the instruction manual carefully and keep it for future reference.
CONTENT
1. FEATURES OF THE RUSSELL HOBBS VIVAĆE CAPSULE COFFEE MAKER
2. FEATURES OF THE RUSSELL HOBBS VIVAĆE MILK FROTHER
3. IMPORTANT SAFEGUARDS
4. VIVAĆE CAPSULE COFFEE MAKER:
a. Parts Diagram
b. Introduction
i. Espresso
ii. Cappuccino
iii. Latte
iv. Before First Use
v. Recommended Coffee Capsule Type
c. Operating Instructions
i. Indicator Light Guide
ii. Filling or Re-filling the Water Reservoir
iii. Rinsing the Appliance and Its Internal Piping
iv. Pre-Brewing Option
v. Brewing Coffee
vi. Re-filling the Internal Circuits Should the Water Reservoir Run Empty During
Operation
vii. How to Program Dispensing Volume
viii. Energy-Saving Mode
d. Cleaning and Maintenance
i. Emptying the Used Capsule Container/ Bin and the Drip Tray
ii. Cleaning the Coffee Machine
iii. Steaming Out/ Storage/ Transport
iv. Descaling/ Decalcification
e. Factory Reset
f. Trouble Shooting
5. VIVAĆE MILK FROTHER:
a. Parts Diagram
b. Before First Use
c. Operating Instructions
d. Cleaning and Maintenance

3
e. Trouble Shooting
6. STORING THE APPLIANCE
7. SERVICING THE APPLIANCE
8. CHANGING THE PLUG
9. RECIPES TO GET YOU STARTED
10. WARRANTY
FEATURES OF THE RUSSELL HOBBS VIVAĆE CAPSULE COFFEE MAKER
•1260W
•19 bar Italian pump
•Short (Ristretto), Espresso and Long (Lungo) plus milk based coffee recipes: Cappuccino,
Macchiato, Lattes, Iced/ Cold Coffee drinks
•Luxurious Barista quality coffee at the touch of a button
•Fresh coffee, perfect every time!
•Ultra-fast Thermoblock heating system –preheating time: 40 seconds
•Transparent 0.8L removable water tank with handle and easy refill lid
•Convenient ‘empty water tank’ warning indicator system
•Illuminated control panel
•Intelligent pre-brewing function reaches the ideal brewing temperature for optimal coffee
and flavour extraction
•Decalcification function
•Automatic and programmable coffee volume control
•Adjustable dispenser for various cup size: 80mm-109mm
•Used capsule bin accommodates 10 used capsules
•Removable drip tray
•Easy capsule insertion with auto capsule ejection system
•Energy saving mode after 15 minutes of inactivity
•Suitable for most Nespresso compatible capsules
•Die cast and stainless steel construction
FEATURES OF THE VIVAĆE MILK FROTHER
•450W
•Soft touch, double wall jug with easy pour spout
•Capacity: 150ml for milk frothing or 300ml for milk warming
•Dual function: hot or cold milk frothing
•Froth milk in less than 120 seconds and heat milk in less than 180 seconds

4
•Removable whisk
•Convenient cordless 360 degree construction
•Non-stick coating for easy cleaning
•One touch operation with auto switch off
•Non-slip rubber feet
•With Min and Max level indicators
IMPORTANT SAFEGUARDS
When using any electrical appliance, basic safety precautions should always be followed including
the following:
1. Please read the instructions carefully before using any appliance.
2. Always ensure that the voltage on the rating label corresponds to the mains voltage in your
home.
3. Incorrect operation and improper use can damage the appliance and cause injury to the
user.
4. This appliance is intended for household use only. Commercial use invalids the warranty
and the supplier cannot be held responsible for injury or damage caused when using the
appliance for any other purpose than that intended.
5. Avoid any contact with moving parts.
6. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
7. Children should be supervised to ensure that they do not play with the appliance.
8. Check the power cord and plug regularly for any damage. If the cord or the plug is
damaged, the manufacturer or a qualified person must replace it in order to avoid an
electrical hazard.
9. Do not use the appliance if it has been dropped or damaged in any way. In case of damage,
take the unit in for examination and/or repair by an authorised service agent
10. To reduce the risk of electric shock, do not immerse or expose the unit, plug or the power
cord to water or any other liquid. Do not use it with wet hands.
11. Never immerse the unit in water or any other liquid for cleaning purposes.
12. Remove the plug from the socket by gripping the plug. Do not pull on the cord to disconnect
the appliance from the mains. Always the unit to cool and unplug it when not in use, before
cleaning or when adding or removing parts.
13. Insert and use only original parts.

5
14. The use of accessory attachments or coffee capsules that are not recommended or
supplied by the manufacturer may result in injuries, fire or electric shock.
15. A short cord is provided to reduce the hazards resulting from becoming entangled in or
tripping over a longer cord.
16. Do not let the cord hang over the edge of a table or counter. Ensure that the cord is not in a
position where it can be pulled on inadvertently, squashed between surfaces or scrapped
across sharp surfaces.
17. Do not allow the cord to touch hot surfaces and do not place on or near a hot gas or electric
burner or in a heated oven.
18. Keep the appliance and cord away from direct radiant heat from the sun, from damp, from
sharp edges and other dangers.
19. Do not use the appliance on a gas or electric cooking top or over or near an open flame.
20. Use the appliance on a hard, flat level surface only, to avoid interruption of airflow
underneath the appliance.
21. Use of an extension cord with this appliance is not recommended. However, if it is
necessary to use an extension lead, ensure that the lead is suited to the power
consumption of the appliance to avoid overheating of the extension cord, the appliance or
plug point. Do not place the extension cord in a position where it can be pulled on by
children or animals or tripped over.
22. This appliance is not suitable for outdoor use. Do not use this appliance for anything other
than its intended use.
23. This appliance is intended to be used in household and similar applications such as:
oStaff kitchen areas in shops, offices and other working environments;
oFarm houses;
oBy clients in hotels, motels and other residential type environments;
oBed and breakfast type environments.
24. Do not operate this appliance by means of an external timer or separate remote control
system.
25. Never operate the appliance without water in the water reservoir. Always make sure that
there is water in the reservoir, not less than at the minimum water level mark.
26. Always be sure to place the water reservoir tightly back in the unit with its lid closed and fill
with water at or above the minimum level marking before turning the appliance ON.
27. Caution should be taken when moving any appliance containing or in contact with hot
liquids.
28. To make sure that the machine is switched OFF, unplug the appliance from the socket/
power point.
29. Do not cover the appliance at any time.
30. Keep children away from the appliance during operation.
31. Danger of scalding! Never move the appliance during operation!

6
32. Danger of scalding! Never touch very hot parts of the appliance (e.g. brew unit during
operations). Do not touch the steam or water jets. Do not move the operating lever when
the machine is building/ generating pressure.
33. Always unplug the appliance before:
orelocating the machine
ocleaning or maintenance
olong periods of disuse
34. Do not remove the water reservoir until the unit is turned OFF.
35. DO NOT carry any appliance by the power cord.
36. Do not leave this appliance unattended during use. Always unplug the unit when not in use
or before cleaning.
37. It is absolutely necessary to keep this appliance clean at all times as it comes into direct
contact with food.
38. Do not touch any hot surfaces, use handles or knobs.
39. Ensure that the switch is in the “0” / “OFF” position after each use.
40. To protect against fire, electric shock, and injury to persons, do not immerse the cord, plug,
or non-stick carafe of the milk frother in water or other liquid.
41. Do not use the Milk Frother other than for heating or frothing milk.
42. Milk can remain hot for some considerable time. Do not touch the jug/ carafe while heating
as it is hot.
43. Do not remove the lid of the Milk Frother during heating or frothing or while the Milk Frother
is in operation as scalding may occur.
44. Do not use the Milk Frother to heat oil, wax or to melt butter.
45. Use the Milk Frother for heating milk or half-and-half ONLY. Do not use it to cook, whisk or
heat any other foods. Use water to clean as described in the Cleaning and Maintenance
section of this instruction manual.
46. Do not place any container inside the Milk Frother —milk must be removed from the
packaging, container, can, etc. before being put into the carafe/ jug.
47. Before serving or removing contents from the Milk Frother, please remove the carafe/ jug
from its base and unplug the cord from the electrical outlet.
48. Do not use the Milk Frother to warm milk for baby or infants
49. The Milk Frother and its components are not dishwasher safe.
50. Milk Frother information - Minimum capacity: 80ml. Maximum capacity: 150ml for milk
frothing. 300ml for milk warming.
51. CAUTION: To prevent plasticizers from migrating to the finish of the countertop or table top
or other furniture, please place NON-PLASTIC coasters or place mats between the
appliance and the finish of the counter top or table top. Failure to do so may cause the
finish to darken or permanent blemishes may occur or stains can appear.

7
52. The manufacturer does not accept responsibility for any damage or injury caused by
improper or incorrect use, or for repairs carried out by unauthorised personnel.
53. In case of technical problems, switch off the machine and do not attempt to repair it yourself.
Return the appliance to an authorised service facility for examination, adjustment or repair.
Always insist on the use of original spare parts. Failure to comply with the above mentioned
pre-cautions and instructions, could affect the safe operation of this machine.
CAUTION: PRESSURE
In order to avoid possible burns to body parts and/or other injury from hot steam and water or
damage to the unit, never remove the water reservoir or the coffee capsule while your coffee
maker is brewing coffee and never remove the lid whilst your milk frother is frothing or heating.
Please also do not lift the operating level during this time. If you need to add more water to the
water reservoir or milk to the milk frothing jug, please make sure that the unit is switched OFF
correctly.

8
VIVAĆE CAPSULE COFFEE MAKER:
PARTS DIAGRAM
F
No.
Name
A.
Operating Handle
G.
Water Reservoir with handle (removable)
B.
Control Panel with buttons
H.
Power Cord
C.
Coffee Dispenser Spout
I.
Main Power Switch (ON/ OFF)
D.
Drip Tray Set
J.
Used Capsule Container/ Bin
Short espresso button
Lungo
Espresso
button
Normal
espresso
button
J
K
L
D

9
E.
Appliance Body or Wall
K.
Drip Tray Cover
F.
Water Reservoir Cover
L.
Drip Tray (removable)
INTRODUCTION
Please read ALL of the instructions, cautions, notes and warnings included in this instruction
manual carefully before you begin to use the coffee maker. When this appliance is used, some
parts and accessories get hot and need to cool down. Proper care and maintenance will ensure
the long life of the Russell Hobbs Vivaće Capsule Coffee Maker with Milk Frother and its reliable/
consistent operation. Save these instructions and refer to them often for cleaning and care tips.
ESPRESSO
A unique method of coffee brewing in which hot water is forced through finely ground coffee.
Popular in Europe, it is a more full-bodied brew than regular drip coffee because of its richness.
Espresso is usually served in demitasse cups.
CAPPUCCINO
A drink made with about 1/3 espresso, 1/3 steamed milk and 1/3 frothed milk.
LATTE
A drink made with about 1/4 espresso and 3/4 steamed milk.
BEFORE FIRST USE
1. Before using your appliance for the first time, remove the coffee maker from the box and take
off any protective wrappings. REMEMBER: DO NOT LEAVE PROTECTIVE PACKAGING
LYING AROUND, AS IT COULD BE DANGEROUS AROUND INFANTS AND CHILDREN.
2. After unpacking, please check that the following items are included:
owater reservoir
ocoffee machine
oinstruction manual with warranty information
3. Please check that your home power supply voltage is the same as marked on the appliance
rating label.

10
4. Tip: keep the packaging for transporting the appliance (e.g. for relocating, servicing, storage,
etc.)
5. Place the appliance on a dry, level surface.
6. Please refer to the “PARTS DIAGRAM” section to familiarize yourself with the coffee maker
and identify all the parts.
7. Please make sure the unit is switched OFF/ “0” by pressing the power button located on the
side of the unit. Make sure that it is unplugged from the electrical outlet.
8. Thoroughly rinse the water tank with fresh water before using for the first time. Clean the
capsule coffee machine by using a damp cloth only. NOTE: In order for your appliance to
work properly time after time, we recommend that it must be cleaned regularly.
Special Note: after unpacking, you may find that a little water has remained in the appliance. In
order to ensure that this appliance works perfectly, it was quality tested with water before leaving
our factory.
Caution: improper handling of electrical equipment is dangerous and can be lethal. Please pay
attention to the safety precautions in this manual, in particular the following:
Danger of scalding: beware of hot water, hot parts as well as steam.
Do not operate the appliance with an empty water reservoir or if the water in the reservoir is
less than the MINIMUM level requirement.
Do not open the operating handle whilst the machine is brewing.
Always remove the power cord from the socket and ensure that the appliance is OFF
before cleaning.
Only use the appliance in a room that is dry and clean.
Recommended Coffee Capsule Type
This capsule coffee maker has been designed to use *Nespresso capsules or certain compatible
capsules. If you are going to use the latter, please contact our Service Department to check and
determine if that type of compatible capsule has been verified by our factory. This appliance does
not work successfully with all compatible capsules.

11
*Nespressois the trade mark of Nestlé Nespresso S.A. Home of Living Brands is not affiliated with
the coffee machine manufacturer or the machine distributor/seller.
OPERATING INSTRUCTIONS
INDICATOR LIGHT GUIDE
Indicator Light
What You Should See
Status
Action Required
Round Indicator
Light (situated
just above the
control panel)
Solid/ steady red light.
First use.
Refer to “Rinsing the
Appliance and its Internal
Piping”.
Solid/ steady red light.
The water reservoir
may be empty.
Fill the water reservoir,
open the operating
handle, then press any
button to fill the internal
circuit.
Solid/ steady blue
light.
Stand-by mode.
Control Panel
Button Lights
Flashing control panel
lights. The machine
is warming up.
Wait for until the appliance
is ready.

12
Solid/ steady control
panel lights.
Ready.
Each control panel
button appears to
flash in a circular
pattern/ fashion.
In energy-saving mode.
Blue Light in
the Used
Capsule
Container/ Bin
The blue capsule
container/ bin light is
solid/ steady for visual
checking when the
operating handle is
open.
Check if the used capsule
container/ bin is full.
FILLING OR RE-FILLING THE WATER RESERVOIR
Before using this appliance for the first time or after long periods of not operating the appliance, the
machine must be rinsed out. This short procedure will rinse and clean the internal piping
thoroughly.
First note that there are two ways to fill the water reservoir: directly into the water reservoir by
using for example a jug or by removing the water reservoir from the appliance.
Filling without removing the water reservoir:
Lift the water reservoir lid
Fill the water reservoir up to the “MAX” level
mark with cold fresh water (the maximum
capacity is 0.8 litre), or fill at least the “MIN” level
mark as shown in figure 1.
Lower and close the water reservoir lid
Figure 1.

13
Filling by removing the water reservoir:
Hold the water reservoir handle at a tilting angle
as shown in figure 2. to remove the water
reservoir from the appliance
Fill the water reservoir up to the “MAX” level
mark with cold fresh water (the maximum
capacity is 0.8 litre), or fill at least the “MIN” level
mark
Slide the water reservoir slowly on to the water
reservoir base. When the water reservoir outlet
is inserted on to the inlet receptacle, pushing it
firmly on the handle as shown in figure 3. to lock
the water reservoir into place
RINSING THE APPLIANCE AND ITS INTERNAL PIPING
1. Fill water reservoir to maximum level mark.
2. Plug the appliance in to the power outlet and
turn the appliance ON.
3. The lights on the control panel buttons will start
flashing. The blue lights in the used-capsule
container/ bin are showing blue. These will go
off after 1 minute. Tip: you can see when the
used capsule container/ bin are full when the
blue lights are on.
4. The round indicator light on the control panel
will flash red indicating first use. This means
that the internal circuit is empty. Please fill up
the water reservoir and open the operating
handle. Press any button to start the pump.
Once water is detected entering the internal
circuit, the red indicator light will turn blue.
5. The appliance will now start to heat up
automatically and all three (3) control panel
buttons will begin flashing.
Figure 2.
Figure 3.

14
6. The lights on the buttons will stop flashing and
turn a solid white colour when the machine has
heated up. Heating up will take approximately
forty (40) seconds.
7. Before pressing any buttons, make sure that:
othe operating handle is closed without
a capsule inside
othe water reservoir is full
othe water reservoir is firmly in place to
prevent leakage
othe drip tray with the used capsule
container/ bin is completely inserted
(never operate the machine without the
drip tray set in place (part D shown in
“PARTS DIAGRAM”) or hot water will
run out when opening handle
oa large bowl ( 250ml size or larger) is
placed under the dispenser spout
8. Now press the Lungo coffee button.
9. Press the middle button to start the rinsing
process.
10. You will notice water running from the
dispenser spout into the large bowl or cup.
11. Open the operating handle once the rinsing
process has stopped automatically.
12. Empty the large bowl.
13. The rinsing process is now completed.
PRE-BREWING OPTION
Pre-brewing is a great function as it will ensure brewing of espressos at a better temperature and
allow for optimum coffee extraction. You can turn this function OFF if desired or choose a different
pre-brewing mode.

15
To enter the pre-brew mode, please follow the instructions below:
1. Turn the machine OFF.
2. Press the middle button and hold the
button down (pressed).
3. Switch the machine ON whilst still pressing
the middle button.
4. Release the button after three (3) seconds
or once you have heard two (2) beeps.
5. Now choose the desired setting.
6. Press the middle button in order to choose
the preferred setting. Referring to the
status table:
Status
Description
Function
Solid/ steady red,
round indicator light.
Disable the pre-brewing
function.
Blue flashing, round
indicator light.
Short pre-brewing.
Solid/ steady blue,
round indicator light.
Long pre-brewing
(default).
BREWING COFFEE
1. Place an empty cup under the dispenser
spout. For smaller cups, you may lower the
dispensing spout down so that it is closer to
the lip of the cup.
2. Move the operating handle back completely.

16
3. Insert a capsule so that it falls straight into the compartment correctly.
4. Close the operating handle firmly to load the capsule.
5. Now press the desired coffee button only once.
6. The selected button will begin flashing and the machine has started to brew coffee. The
machine will stop automatically dispensing once it has reached the default brewing volume
(25ml for Short Espresso, 40ml for Normal Espresso and 110ml for Lungo espresso). Note:
the default setting can be programmed to your preferred dispensing volume. Please refer
to “How to Program Dispensing Volume”.
7. Raise the operating handle to automatically eject the used capsule into the container/ bin.
8. Close the operating handle.
Tip: when using the machine and it is considered ‘cold’ (for example, using the machine in
the morning or in idle time for longer than 1 hour), it is suggested to brew water first in order
to remove the residual taste of the last cup which was brewed.
REFILLING THE INTERNAL CIRCUIT SHOULD THE WATER RESERVOIR RUN
EMPTY DURING BREWING
It is strongly suggested to ensure that there is enough water in the water reservoir before making
coffee. Ensure that water is poured in the reservoir and that it reaches the minimum level mark at
least.
In case the water reservoir runs empty during the coffee brewing process, you can stop it by
pressing the selected button which is flashing.
Open the operating handle to eject the used capsule. CAUTION: Beware of hot steam as there is
danger of scalding!
Fill the water reservoir and press one of the buttons to start pumping water. Once the circuit is
refilled, the indicator light will turn from red to blue.
HOW TO PROGRAM DISPENSING VOLUME
Ensure that there is enough water in the water reservoir before programming the coffee dispensing
volume.
1. Place an empty cup under the dispenser
spout. For smaller cups, you may lower the

17
dispensing spout down so that it is closer to
the lip of the cup.
2. Move the operating handle back completely.
3. Insert a capsule so that it falls straight into the
compartment correctly.
4. Close the operating handle firmly to load the
capsule.
5. Press the desired button and hold it pressed
down. Once the desired volume has been
reached, release the button. The button is
now programmed to your preference.
6. After the programming, the dispensing size will have been recorded in the appliances
memory. For next use, press the button normally and press only once.
7. You may program the other buttons if desired.
Note the volume range:
25ml~150ml based on Nespresso “Ristretto” capsule & “Lungo” capsule.
The default size is 25ml (Short Espresso), 40ml (Normal Espresso) and 110ml (Lungo
Espresso).
Tip: when the programming process has finished, leave the machine for 30 seconds so that it may
cool down prior to opening the operating handle.
The flashing sequence equates to one (1) second = one (1) flash. You can count the flashes to
determine the brewing time.
OR
OR

18
ENERGY-SAVING MODE
The appliance enters energy-saving mode automatically once the machine is idle for 15 minutes.
The three (3) buttons will flash cyclically in energy-saving mode. If you would like to exit energy-
saving mode, please press any button. The appliance will start to warm up and the lights will flash.
Once the buttons are solid/ steady, the machine is ready to brew coffee.
CLEANING AND MAINTENANCE
This appliance is for household use only and is not user-serviceable. Do not open or change any
parts by yourself. Please refer to a qualified electrical service department or return to the supplier
if servicing is necessary. Always remember to unplug the unit from the electrical outlet when not in
use and before cleaning. Ensure that the power button is set to OFF “0”.
EMPTYING THE USED CAPSULE CONTAINER/ BIN AND THE DRIP TRAY
The used capsule container/ bin holds around
(ten) 10 used capsules. We recommend emptying
the used capsule container/ bin and the drip tray
every day. You can see if the used capsule
container/ bin are full when the blue light is ON
inside the used capsule container/ bin.
1. Raise the operating handle to ensure that
there are no capsules inside the brewing
compartment.
2. Raise the dispensing spout up if it is in a
lowered position.
3. Hold the drip tray firmly and pull it out by
lifting it gently.
4. Dispose of used capsules and empty the
drip tray.
5. The used capsule container/ bin can be
detached (if necessary) from the lower drip
tray (it uses a snaplock design).
6. Rinse the drip tray set with fresh water.

19
7. Throw out the old water from the water
reservoir. Rinse the water reservoir with
fresh water.
8. After emptying/ cleaning, reassemble the
parts in reverse order and insert them back
into/ onto the appliance so that they are
correctly in place.
Note: the plastic parts of the appliance are not dishwasher safe.
CLEANING THE COFFEE MACHINE
1. Always pull the plug out from the main power supply and ensure that the coffee machine is
switched OFF before cleaning the machine
2. Never immerse the machine in water or clean it under running water. Clean the machine
with a dry cloth.
3. Never use abrasive cleaning agents or materials (use e.g. dry rags or kitchen paper).
STEAMING OUT/ STORAGE/ TRANSPORT
Prior to long periods of not using the machine or for storage or transport at temperatures below 5
°C, it is essential to steam out the machine. This removes water from the system to prevent
internal frost damage.
1. Turn the machine ON.
2. Empty the water reservoir and place it back
into its correct position.
3. Put an empty cup under the dispensing
spout.
4. Press the Lungo button to start brewing.
5. The steaming out process has now started.
6. After the pump stops automatically, the
steaming out process is completed.
7. Turn the machine OFF and unplug from its power supply.
CAUTION: Beware of hot steam as there is danger of scalding!

20
DESCALING/ DECALCIFICATION
Mineral deposits building up in the coffee maker will have an adverse effect in the operation of the
appliance. Deposited residues in the machine can block the piping and cause damage.
Your appliance must be descaled when you begin to notice an increase in the time required to
brew espresso or when there is excessive steaming. The frequency of cleaning depends upon the
hardness of the water used. Drinking water varies according to region.
To prevent adverse effects of mineral deposits/ lime scale, be sure to decalcify the machine at the
very least after making three hundred to four hundred (300 to 400) cups of coffee or, in any case if
the output falls significantly or, after one or two (1 to 2) months.