Ryobi LCDI1402 Operation manual
1. Keyless chuck
2. Torque adjustment ring
3. Quick mode selector
4. Two-speed gear train
5 . Rotation selector (forward/reverse/center lock)
6. Bit storage
7. Trigger switch
8. Mag Tray™
9. Battery pack
10. Latches
11. Depress latches to release battery pack
12. Reverse
13. Forward
14. Chuck jaws
15. Lock (tighten)
16. Unlock (release)
17. Low speed
18. High speed
19. Drive mode
20. Drill mode
21. Hammer mode
22. To increase torque
23. To decrease torque
24. Bit
25. Screws
26. Bit holder
27. Drill bit
28. Chuck sleeve
1
2
3 4
5
7
9
6
810
11
9
8
7
26 25
24
Fig. 1 Fig. 2
19 20 21
3
57
12
13
14
15
16
28
4
17
18
LO
HI
23
22
2
14
15 28
27
16
19 20
21
Fig. 3
Fig. 4
Fig. 5
Fig. 7
Fig. 6
Fig. 8
It is essential that you read the instructions in this manual before
operating this machine.
Subject to technical modifications.
1
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
The term "power tool'' in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cluttered or dark
areas invite accidents.
Power tools
create sparks which may ignite the dust or fumes.
Distractions can cause you
to lose control.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
There is an increased risk of electric
shock if your body is earthed or grounded.
Water entering a power tool will increase
the risk of electric shock.
Damaged or entangled cords increase
the risk of electric shock.
Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
Use of an RCD reduces the risk of
electric shock.
The term ''residual current device (RCD)''
may be replaced by the term ''ground fault circuit
interrupter (GFCI)'' or ''earth leakage circuit breaker
(ELCB)''.
A
moment of inattention while operating power tools
may result in serious personal injury.
Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
This enables better control of
the power tool in unexpected situations.
Loose clothes, jewellery or
long hair can be caught in moving parts.
Use of dust
collection can reduce dust-related hazards.
The correct power
tool will do the job better and safer at the rate for
which it was designed.
Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
2
Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
Power tools are dangerous in the hands
of untrained users.
Many accidents are caused by
poorly maintained power tools.
Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use of the power tool for
operations different from those intended could result
in a hazardous situation.
A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
Use of any other battery packs may
create a risk of injury and fire.
Shorting the battery terminals together may
cause burns or a fire.
Liquid ejected from the battery may cause irritation or
burns.
This appliance is not intended for use by young children
or inrm persons unless they have been adequately
supervised by a responsible person to ensure that they
do not play with the appliance.
Visitors should
wear safety glasses and be kept a safe distance from
the work area. Do not let visitors contact the tool or
extension cord.
This will ensure that the safety of the power
tool is maintained.
Exposure to noise can cause hearing loss.
Loss of control can cause personal injury.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Voltage 14.4 V
Chuck 2-13 mm
Switch Variable speed
No load speed (Drill mode):
-Lo speed 0-440 min-1
-Hi speed 0-1600 min-1
Hammer speed (Blows per minute):
-Lo speed 0-5720 min-1
-Hi speed 0-20800 min-1
Max. torque 37.5 Nm
Weight (not incl. battery pack) 1.43 Kg
3
(not included)
(not included)
LCDI1402
Do not allow familiarity with products to make
you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
Always wear safety goggles or safety glasses
with side shields when operating products.
Failure to do so could result in objects being
thrown into your eyes, resulting in possible
serious injury.
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or accessories
not recommended can result in serious personal
injury.
You may use this product for the purposes listed below:
Drilling in all types of wood products (lumber,
plywood, panelling, composition board, and hard
board)
Drilling in ceramics, plastics, fiberglass, and laminates
Drilling in metals
Driving screws
Hammer drilling in brick, or other masonry
This product will accept RYOBI 14.4 V lithium-ion battery
packs and RYOBI 14.4 V nickel-cadmium battery packs.
RYOBI 14.4 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximise
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
See Figure 2.
Lock the trigger switch by placing the rotation selector
in the center position.
Place the battery pack on the tool.
Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
on the tool before beginning operation.
Always remove battery pack from your tool when
you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could
cause serious personal injury.
See Figure 2.
Lock the trigger switch by placing the rotation selector
in the center position.
Depress the latches on the side of battery pack.
Remove the battery pack from the tool.
Battery tools are always in operating condition.
Therefore, the switch should always be locked
when not in use or carrying at your side.
4
See Figure 3.
To turn the drill , depress the trigger switch.
To turn it , release the trigger switch.
The variable speed trigger switch delivers higher speed
and torque with increased trigger pressure and lower
speed with decreased trigger pressure.
You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
See Figure 3.
The bit rotation is reversible and is controlled by a selector
located above the trigger switch. With the drill held in
normal operating position, the rotation selector should be
positioned to the left of the trigger switch for forward drilling.
The drilling direction is reversed when the selector is to the
right of the trigger switch.
Setting the trigger switch in the (center lock) position
helps reduce the possibility of accidental starting when not in
use.
To prevent gear damage, always allow the chuck
to come to a complete stop before changing the
direction of rotation.
To stop the drill, release the trigger switch and allow the
chuck to come to a complete stop.
The drill will not run unless the rotation selector is
pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage
may cause the drill to become overheated. If this occurs,
cool the drill by running it without a load and at full speed.
The internal spindle lock allows the user single-handed
control of chuck adjustments and bit changes. Squeezing
the chuck body stops the chuck jaws from turning. For
bit changes and chuck adjustments, squeeze the chuck
body and turn.
See Figure 4.
The drill has a keyless chuck to tighten or release drill
bits in the chuck jaws. The arrows on the chuck indicate
which direction to rotate the chuck body in order to
(tighten) or (release) the drill bit.
Do not hold the chuck with one hand and use the
power of the drill to tighten the chuck jaws on the
drill bit. The chuck body could slip in your hand,
or your hand could slip and come in contact with
the rotating drill bit. This could cause an accident
resulting in serious personal injury.
See Figure 5.
The drill has a two-speed gear train designed for drilling
or driving at or ) speeds. A slide switch is
located on top of the drill to select either or
speed. When using drill in the speed range, speed
will decrease and unit will have more power and torque.
When using drill in the speed range, speed will
increase and unit will have less power and torque. Use
speed for high power and torque applications and
speed for fast drilling or driving applications.
If you have difficulty changing from one gear
range to the other, turn the chuck by hand until the gears
engage.
Never change gears while the tool is running.
Failure to obey this caution could result in
serious damage to the drill.
See Figure 6.
The Quick Mode Selector allows you to quickly switch
from drill mode to drive mode.
In general, drill mode should be used for drilling and
other heavy duty applications. Drive mode should be
used for driving screws.percussion mode should be used
for impact drilling.
See Figure 5-6.
Using the chart below, choose correct speed and mode
the type of bit, fastener, and material you will be using.
Choose your
Choose the correct
Choose the correct
5
• Lag screws up to 9.5 mm dia. by 38.1 mm long
• Hole saw up to 38.1 mm
• Spade bits up to 19.1 mm
• Drill bits up to 12.7 mm
• Drilling into metal
• Concrete screws
1/LOW DRILL MODE
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH
• Deck or wood screws up to 76.2 mm long
• Self tapping screws 1/LOW DRIVE MODE
• Deck or wood screws up to 50.8 mm long
• Small screws or delicate work that requires more control 2/HIGH
• Masonry bit up to 12.7 mm
1/LOW HAMMER MODE
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH
See Figure 7.
When using the drill-driver for various driving
applications, it becomes necessary to increase
or decrease the torque in order to help prevent the
possibility of damaging screw heads, threads, workpiece,
etc. In general, torque intensity should correspond to the
screw diameter. If the torque is too high or the screws too
small, the screws may be damaged or broken.
The torque is adjusted by rotating the torque adjustment ring.
The torque is greater when the torque adjustment ring
is set on a higher setting. The torque is less when the
torque adjustment ring is set on a lower setting.
The proper setting depends on the type of material and
the size of screw you are using.
See Figure 2.
When not in use, bits provided with the drill can be placed
in the storage areas located on the base of the drill.
See Figure 2.
The magnetic tray conveniently stores screws or other
small parts.
See Figure 8.
Lock the trigger switch by placing the rotation selector
in the center position.
Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend
to use. Also, raise the front of the drill slightly to keep
the bit from falling out of the chuck jaws.
Insert the drill bit.
Tighten the chuck jaws on the drill bit.
:
Make sure to insert the drill bit straight into the
chuck jaws. Do not insert the drill bit into the
chuck jaws at an angle then tighten. This could
cause the drill bit to be thrown from the drill,
resulting in possible serious personal injury or
damage to the chuck.
Rotate the chuck body in the direction of the
arrow marked to tighten the chuck jaws. Do not
use a wrench to tighten or loosen the chuck jaws.
See Figure 8.
Lock the trigger switch by placing the rotation selector
in the center position.
Open the chuck jaws.
Rotate the chuck body in the direction of the
arrow marked to loosen the chuck jaws. Do
not use a wrench to tighten or loosen the chuck jaws.
Remove the drill bit.
Check the rotation selector for the correct setting
(forward or reverse).
Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
6
Hold the drill firmly and place the bit at the point to be
drilled.
Depress the trigger switch to start the drill.
Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
:
Be prepared for binding at bit breakthrough.
When these situations occur, drill has a tendency
to grab and kick opposite to the direction of
rotation and could cause loss of control when
breaking through material. If not prepared, this
loss of control can result in possible serious
injury.
When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life
of the bit and increase the drilling action.
If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
This drill has an electric brake. When the trigger
switch is released, the chuck stops turning. When the
brake is functioning properly, sparks will be visible
through the vent slots on the housing. This is normal and
is the action of the brake.
When servicing, use only identical RYOBI
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
Do not at any time let brake fluids, gasoline,
petroleumbased products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
961067428-01
Table of contents
Other Ryobi Drill manuals
Ryobi
Ryobi R18DDP2 User manual
Ryobi
Ryobi RPD18X User manual
Ryobi
Ryobi PCL220 User manual
Ryobi
Ryobi P240 Configuration guide
Ryobi
Ryobi R18PD3 User manual
Ryobi
Ryobi HJP003 User manual
Ryobi
Ryobi CMD-1802M User manual
Ryobi
Ryobi R18PD5 User manual
Ryobi
Ryobi LCDI1802 User manual
Ryobi
Ryobi CLD-18 User manual
Ryobi
Ryobi R18DD3 User manual
Ryobi
Ryobi EID1050RB Operation manual
Ryobi
Ryobi P212 Quick setup guide
Ryobi
Ryobi CHD-1201 User manual
Ryobi
Ryobi CHI1442P Operation manual
Ryobi
Ryobi LCDI1802 Operation manual
Ryobi
Ryobi EID11002RV User manual
Ryobi
Ryobi D47C User manual
Ryobi
Ryobi R18MMS-0 User manual
Ryobi
Ryobi HD1800M User manual
