Ryobi R18XTRP10 User manual

R18XTRP10

2
Original Instructions
IMPORTANT!
It is essential that you read the instructions
in this manual before assembling, operating,
and maintaining the product.
Subject to technical modication.
Safety, performance, and dependability have
been given top priority in the design of your
cordless transfer pump.
INTENDED USE
The cordless transfer pump is intended to
transfer water, either dirty or clean, out of
pools, ponds, or tanks. The product can be
used to drain water from oods or excess
rainwater during oods.
The product is intended only for home or
domestic use. The product may be used
indoors or outdoors.
Do not use the product for any other purpose.
GENERAL SAFETY WARNINGS
■Never allow children, persons with reduced
physical, sensory, or mental capabilities or
lack of experience and knowledge, or people
who are unfamiliar with these instructions
to use the product. Local regulations may
restrict the age of the operator. Children
should be adequately supervised to ensure
that they do not play with the product.
■Save all warnings and instructions for future
reference. Refer to them frequently, and
use them to instruct others who may use the
product. If you loan someone the product,
also loan them these instructions to prevent
misuse of the product and possible injury.
■Keep the area of operation clear of all
persons, particularly small children and
pets.
■Inspect the product before each use. Check
for loose fasteners, etc. Make sure that
all guards and handles are properly and
securely attached. Replace any damaged
parts before use. Check for battery pack
leaks.
■Do not modify the product in any way or
use parts and accessories that are not
recommended by the manufacturer.
■Do not operate the product while barefoot or
when wearing sandals or similar lightweight
footwear. Wear protective footwear that will
protect your feet and improve your footing
on slippery surfaces.
■Exercise caution to avoid slipping or falling.
■Avoid inserting hands into the inlets/outlets
of the product while it is turned on.
■Do not install or operate the product in an
explosive environment or near flammable
materials.
■Do not use the product if the switch does
not turn it off. Have the switch replaced by
an authorised service centre.
■Turn off the product, remove the battery
pack, and allow the product to cool down.
Make sure that all moving parts have come
to a complete stop:
●before servicing
●before clearing a blockage
●before checking, cleaning, and working
on the product
●before changing accessories
●before leaving the product unattended
●whenever performing maintenance
■Immediately turn off the product and remove
the battery pack in the event of an accident
or breakdown. Never operate the product
again until it has been fully checked by an
authorised service centre.
BATTERY TOOL USE AND CARE
■Recharge only with the charger specified by
the manufacturer. A charger that is suitable
for one type of battery pack may create a
risk of fire when used with another battery
pack.
■Use only battery packs intended specifically
for the product. Use of any other battery
packs may result in a risk of fire, electric
shock, or injury to persons.
■Do not use a battery pack or product that
is damaged or modified. Damaged or
modified batteries may exhibit unpredictable
behaviour resulting in fire, explosion, or risk
of injury.
■Do not expose a battery pack or product to
fire or excessive temperatures. Exposure to
fire or excessive temperature above 130°C
may cause explosion.
■When the battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws, or
other small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.

3
Original Instructions
■Under abusive conditions, liquid may be
ejected from the battery. Avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
CORDLESS TRANSFER PUMP SAFETY
WARNINGS
■Ensure that the battery pack is removed
when installing the product.
■Ensure that all connections are leak free.
Use a thread seal tape or a suitable sealant
on the connection thread.
■When tightening threaded connections, do
not apply excessive force that may cause
damage.
■If the product needs to be moved, turn off
the product first and loosen the baseplate if
needed. Move the product to a suitable area
and tighten the baseplate if needed. Turn
on the product to resume operation.
■Do not use the product for corrosive,
abrasive, explosive, or dangerous liquids.
Fluids other than water can damage the
product, can create a fire hazard, and could
cause physical injuries to the operator.
■Do not use the product with potable water.
■Do not operate the product without liquid.
Do not run the product dry.
■Do not use the product when people are in
the water.
■Do not remove the hose while the product is
still operating.
■Water discharged from the product may
cause the ground to become wet and
may cause slipping. Make sure to clean
the discharged water after operating the
product.
■Do not discharge water to areas with
electrical or high voltage elements, active
chemicals, or other objects or substances
that might cause danger when mixed with
water.
■Do not expose the inside of the battery
compartment to rain or wet conditions.
The product is only water resistant when
the battery compartment is closed. Water
entering the product increases the risk of
electric shock.
ADDITIONAL BATTERY SAFETY
WARNINGS
To reduce the risk of re, personal injury,
and product damage due to a short circuit,
never immerse the product, battery pack, or
charger in uid or allow uid to ow inside
them. Corrosive or conductive uids, such as
seawater, certain industrial chemicals, and
bleach or bleach-containing products, etc., can
cause a short circuit.
TRANSPORTATION AND STORAGE
■Turn off the product, remove the battery
pack, and allow both to cool down before
storing or transporting.
■Clean the product thoroughly before storing.
Store the product in a dry, well-ventilated
area that is inaccessible to children. Keep
the product away from corrosive agents,
such as garden chemicals and de-icing
salts.
■When transporting the product in a vehicle,
secure it against movement or falling to
prevent injury to persons or damage to the
product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local
and national provisions and regulations.
Follow all special requirements on packaging
and labelling when transporting batteries
by a third party. Ensure that no batteries
can come in contact with other batteries or
conductive materials while in transport by
protecting exposed connectors with insulating,
nonconductive caps or tape. Do not transport
batteries that are cracked or leaking. Check
with the forwarding company for further advice.
MAINTENANCE
■Use only original manufacturer’s
replacement parts, accessories, and
attachments. Failure to do so can cause
possible injury, can contribute to poor
performance, and may void your warranty.
■Servicing requires extreme care and
knowledge and should be performed only
by a qualified service technician. Have the
product serviced by an authorised service
centre only.
■You may make adjustments and repairs
described in this manual. For other repairs,
contact an authorised service centre.

4
Original Instructions
■Periodically inspect the pump, hoses, and
water inlet. Ensure that the hoses and water
inlet are free from mud, sand, and debris.
■After each use, clean the product with a
soft, dry cloth. Keep the product dry, clean,
and free from oil and grease when not in
use. Any part that is damaged should
be properly repaired or replaced by an
authorised service centre.
■Clean the filter only when there is noticeable
decline of functionality.
■Bring the product to an authorised service
centre to replace damaged or unreadable
labels.
SYMBOLS ON THE PRODUCT
Regulatory Compliance
Mark (RCM). The product
meets applicable regulatory
requirements.
Read and understand all
instructions before operating the
product. Follow all warnings and
safety instructions.
Remove the battery pack before
starting any work on the product.
Ingress protection
Do not dispose of waste
batteries, waste electrical
and electronic equipment as
unsorted municipal waste. Waste
batteries and waste electrical
and electronic equipment must
be collected separately. Waste
batteries, waste accumulators,
and light sources have to be
removed from the equipment.
Check with your local authority
or retailer for recycling advice
and collection point. According
to local regulations, retailers
may have an obligation to
take back waste batteries and
waste electrical and electronic
equipment free of charge. Your
contribution to the reuse and
recycling of waste batteries and
waste electrical and electronic
equipment helps to reduce the
demand of raw materials. Waste
batteries, in particular containing
lithium, and waste electrical
and electronic equipment
contain valuable and recyclable
materials, which can adversely
impact the environment and the
human health if not disposed of
in an environmentally compatible
manner. Delete personal data
from waste equipment, if any.
SYMBOLS IN THIS MANUAL
Parts or accessories sold
separately
Note
Warning
Unlock
Lock

5
Know your product
R18XTRP10
Battery cover latch
Latch connector
Battery cover
Handle
Flow control button
On/o󰀨 button
Timer button
Outlet port
Inlet port
Viewing window
Feet housing
Suction hose
Operator's manual
Filter
Battery pack
Charger

6
Getting started
1
2
7
Place the filter on the area or container
with the water to be transferred.
Press the on/off button to turn on the
product.
Press the timer button to set a timer.
Open the battery cover. Install the battery pack. Make sure that
the latches on the battery pack click into
place.
Always wear eye protection while
operating the product. Wear an
appropriate respiratory mask.
Install the product to the feet housing. Slide the feet housing backward to
secure it. Install the screw and turn it
clockwise to tighten.
Flip up the latch and remove the latch
connector from the groove to unlock the
battery cover.
1 2
8
1
2
3
3
9
13
5min
14 15

7
Getting started
1
2
4
NOTE: Each press of the timer button
sets the timer to 5minutes and the
succeeding press adds another 5
minutes.
Hook the latch connector on the groove
and flip down the latch to lock the
battery cover.
Close the battery cover.
Press the on/off button to stop the
product.
Attach the suction hose to the outlet
port. Turn the coupling of the suction
hose clockwise to tighten.
Attach the filter to the other end of the
suction hose.
Attach the suction hose to the inlet port.
Turn the coupling of the suction hose
clockwise to tighten.
6
2
1
5
1
2
11
H
2
O
H
2
O
1210
7
Pour water into the inlet port to prime
the impeller inside the product.
x 1
x 2
x 3
5min5min
5min10min
5min15min
13
16

8
p.9
p.11
p.13
Operating the
product
Cleaning the
product
Storing the product

9
Operation
1
2
3
2
3
1
H
2
O
H
2
O
1
2
1
2
3
4
5
OPERATING THE PRODUCT
1. Flip up the latch and remove the latch
connector from the groove to unlock the
battery cover. Open the battery cover.
2. Install the battery pack. Make sure that
the latches on the battery pack click into
place.
3. Close the battery cover. Hook the latch
connector on the groove and flip down
the latch to lock the battery cover.
4. Pour water into the inlet port to prime the
impeller inside the product. Place the
filter on the area or container with the
water to be transferred.
5. Press the on/off button to turn on the
product.

10
Operation
x 1
x 2
x 3
LOW
MED
HIGH
x 1
x 2
x 3
5min5min
5min10min
5min15min
6
NOTE: Press the flow control button to
adjust the suction speed. Each press of the
flow control button cycles through the low,
medium, and high speed settings.
NOTE: Press the timer button to set a timer.
Each press of the timer button sets the timer
to 5 minutes and the succeeding press adds
another 5 minutes.
NOTE: Discharge water properly into drains,
gutters, or other appropriate sewage areas.
WARNING: Do not discharge water to areas
with electrical or high voltage elements,
active chemicals, or other objects or
substances that might cause danger when
mixed with water.
6. Press the on/off button to turn off the
product.

11
Maintenance
1
2
3
1
2
2
3
1
1
2
2
1
1
2
3
4
5
CLEANING THE PRODUCT
1. Flip up the latch and remove the latch
connector from the groove to unlock the
battery cover. Open the battery cover.
2. Press the latches on the battery pack and
remove it from the product.
3. Close the battery cover. Hook the latch
connector on the groove and flip down
the latch to lock the battery cover.
4. Turn the coupling of the suction hose
attached to the inlet port counterclockwise
and remove it.
5. Turn the coupling of the suction
hose attached to the outlet port
counterclockwise and remove it.

12
Maintenance
6
6. Clean the product with a soft, dry cloth.
WARNING: Do not use water to clean the
product.

13
Storage
1
2
3
1
2
2
3
1
1
2
2
1
1
2
3
4
5
STORING THE PRODUCT
1. Flip up the latch and remove the latch
connector from the groove to unlock the
battery cover. Open the battery cover.
2. Press the latches on the battery pack and
remove it from the product.
3. Close the battery cover. Hook the latch
connector on the groove and flip down
the latch to lock the battery cover.
4. Turn the coupling of the suction hose
attached to the inlet port counterclockwise
and remove it.
5. Turn the coupling of the suction
hose attached to the outlet port
counterclockwise and remove it.

14
Storage
1
2
6
20220920v1
6. Turn the screw counterclockwise and
remove it.
NOTE: There is a button on the feet housing.
7. Press the button and remove the feet
housing.
8. Store the product in a dry, well-ventilated
area that is inaccessible to children. Keep
the product away from corrosive agents,
such as garden chemicals and de-icing
salts.
1
2
7
8

PRODUCT SPECIFICATIONS
Cordless transfer pump
Model R18XTRP10
Rated voltage 18 V d.c.
Flow rate 37.85 L/min (2,271 L/hr)
Maximum head 16.5 m
Maximum lift 5.2 m
Maximum water temperature rating 35 °C
Maximum particle size 2.5 mm
Inlet/outlet connection size
(GHT male)
3/4 in.
Ingress protection IPX4
Weight (without battery pack) 2.2 kg
Weight (with heaviest battery pack) 3.4 kg
BATTERY AND CHARGER
Model R18XTRP10
Battery pack -
Charger -
Compatible battery
packs
RB18L15, RB18L15A, RB18L15B,
RB18L20, RB18L20A, RB18L25,
RB18L25A, RB18L40, RB18L40A,
RB18L50, RB18L50A, RB18L13,
RB18L60A, RB18L90A, RB1815C,
RB1820C, RB1825C, RB1840C, RB1840X,
RB1850C, RB1850X, RB1860X
ACCESSORIES
Suction hose 5131041965
Filter 5131041966
NOTE: Visit your local special orders desk or contact RYOBI
customer service for replacement parts.
WARNING! The declared vibration total values and the
declared noise emission values given in this instruction
manual have been measured in accordance with a
standardised test and may be used to compare one tool with
another. They may be used for a preliminary assessment
of exposure.
The declared vibration and noise emission values represent
the main applications of the tool. However, if the tool is used
for di󰀨erent applications, used with di󰀨erent accessories,
or poorly maintained, the vibration and noise emission
may di󰀨er. These conditions may signicantly increase the
exposure levels over the total working period. An estimation
of the level of exposure to vibration and noise should take
into account the times when the tool is turned o󰀨 or when
it is running idle. These conditions may signicantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the e󰀨ects of vibration and noise, such as maintaining
the tool and the accessories, keeping the hands warm (in
case of vibration), and organising work patterns.

Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
961479084-01