Safavieh Lighting Moxley User manual

PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY
A mountingplate 1X H Handle 1X
BScrew 4XI Bulb 1X
C Anchor 4X J IronShade 1X
DOutletbox
screw 2X K LampArm 1X
E wireconnector 3X L Tubeplug 1X
FMounting
screw 4X M groundscrew 1X
GBackplate 1X
WARNING
**WERECOMMENDINSTALLATIONOFTHISLIGHTINGFIXTUREBEDONEBYALICENSEDELECTRICIAN**
* Switchoffthemainelectricalsupplyfromthemainfusebox/circuitbreakerbeforeinstallation.
* Inspectitemcarefullybeforeattemptingtoinstall.
* Ifthereisanydamagesorobviousdefects,donotinstall.
* Itemmaynotbereturnedonceithasbeeninstalled.
CAREANDMAINTENANCE
* Tocleantheoutsideofthefixture,useadryorslightlydampenedcleancloth(usecleanwater,nevera
solvent)towipethesurfaceofthefixture.
* Tocleantheinsideofthefixture,firstdisconnectpowertothefixturebyturningoffthecircuitbreakerorby
removingthefuseatthefusebox.Next,useadryorslightlydampenedcleancloth(usecleanwater,nevera
solvent)towipetheinteriorsurfaceofthefixture.
* Donotuseanycleanerswithchemical,solventsorharshabrasives.Useonlyadrysoftclothtodustorwipe
carefully.
NOTICE&IMPORTANTSAFETYINSTRUCTIONS
Model#:SCN4092
ProductDimensions:5.875"LX36.5"W
X24.5"H
* Pleasemakesurethatyouhaveallpartsindicatedbeforeyoubeginassemblyofthisitem
*Thisitemshouldbeassembledonasoftsurfacetopreventscratchingthefinishduringassembly
*Toreducetheriskoffire,electricalshockorinjurytopersonsorproperty,pleasefollowtheguideline
below forsafeuseandinstallation
PartListandHardwareList
1/3

Installationtothewall
NOTE:PLEASEUSETYPE"A"BULBMAX25‐WATTORLEDBULBMAX9‐WATT,THEREISLED5‐WATTBULBINTHEBOX
Step3:Thenloosenthehandle(H),adjusttheheightofthelampbody,rotatetheiron
shade(J),adjustthepositionoftheironcover,rotatethelamparm(K)fromsidetoside,
andinstallthebulb(I)intothesocketafteradjustingtheposition. Step4:Puttheplugintotheplugbase.
* Beforebeginningassemblyofproduct,makesureallpartsarepresent.Comparepartswithpackagecontentslistandhardwarecontentslist.
* Ifanypartismissingordamaged,donotattempttoassembletheproduct.
* EstimatedAssemblyTime:20minutes.
* ToolsRequiredforAssembly(notincluded):Screwdriver,Junctionbox
* Ifyouarehavingdifficulty,ourfriendlyCustomerCareteamisalwaysheretohelp.Pleaseemail[e-mail]
Step1:Firstmarkthepositionoftherubberplugholewiththemountingplate(A),punch
holesonthewallandinstalltheanchor(C),andthenfixthemountingplate(A)onthewall
withscrew(B). Step2:Fixthelamparm(K)onmountingplate(A)withmountingscrew(F).
PREPARATION
AB
C
H
I
J
K
A F
H
K
2/3

Installationtooutletbox
Step2:Wireconnection
GroundingInstructions:
C
onnect
fi
xtureneutra
l
w
i
re
(
r
ibb
e
d)
tot
h
eout
l
et
b
oxneutra
l
w
i
re
(
usua
ll
yw
hi
te
)
usingawireconnector.
Connectfixturehotwire(smoothwithmarkings)totheoutletboxhotwire
(usuallyblack)usingawireconnector.
CAUTION:Donotreversethehotandneutralconnections
Step1:Firstmarkthepositionoftherubberplugholewiththemountingplate(A),punch
holesonthewallandinstalltheanchor(C),andthenfixthemountingplate(A)onthe
junctionboxwithscrew(B)andoutletboxscrew(D)
Step2:Keepthelengthofthefixturewireatleast6in.fromthecenterofthebackplate(G)andcut
thefixturewire.Thenusethewirestrippers(notincluded)toseparateapproximately1/2in.ofthe
insulatedwire.
Wrapgroundwirefromoutletboxaroundgreengroundscrew(M)onmounting
bracket,nolessthan2"fromwireend.Tightengroundscrew.Iffixtureissupplied
withagroundwire,connecttooutletgroundwirewithawireconnector.
Step4:Installthetubeplug(L)at(G1),thenloosenthehandle(H),adjusttheheightofthe
lampbody,rotatetheironshade(J),adjustthepositionoftheironcover,rotatethelamp
arm(K)fromsidetoside,andinstallthebulb(I)intothesocketafteradjustingtheposition.
H
I
J
K
G1
L
AB
C
AEF
M
3/3