Fold Here
Step 3: Connect Camera to Recorder
1. For shim installations only:
Position the shim against the camera base and pull the pigtail through the center of the shim.
2. Connect the pigtail to the camera harness through the panel cable hole.
Important: ensure the camera harness cable has a blue band in front of the connectors, indicating it is AHD-compatible.
3. Connect the camera harness 2x3 Micro-Fit connector to the recorder.
1. Ensure a rubber washer is in place over each of the mounting
screws.
2. Use the alignment peg to position the camera base against
the shim so the cable notch and the mounting holes line up.
3. Slide one of the longer self-drilling mounting screws (No. 10 x
2”) through the camera and the hole at a thicker edge of the
shim, and attach it to the vehicle panel.
4. Repeat step 3 with the other 2” mounting screw.
5. Slide the shorter self-drilling mounting screw (No. 10 x 1.25”)
through the camera and the hole at the thinnest edge of the
shim, and fully attach the camera/shim assembly.
Step 4: Install Camera
B
C
D
1
2
A
B
A
C
D
3
4
5
File Last Saved Date: July-06-17 4:09:25 PM
File Name: HD1Q Install Images
6
TOLERANCES ARE:
REVISION
DIMENSIONS ARE IN MM
UNLESS OTHERWISE NOTED
NO DECIMAL PLACES
1 DECIMAL PLACE
2 DECIMAL PLACE
ANGLES
ARENA Tracking:
ENG:
DRAWN:
DATE
APPROVALS
SEON DESIGN INC.
111 - 3B Burbidge St.
Coquitlam, BC
Canada V3K 7B2
TEL: 604.941.0880
FAX: 604.677.6050
MANUFACTURING DESCRIPTION:
PART NUMBER:
SHEET
SIZE
A
1 of 1
SHEET:
THIRD ANGLE PROJECTION
COPYRIGHT SEON DESIGN INC., ALL RIGHTS RESERVED. THIS DOCUMENT MAY NOT BE DISCLOSED, OR REPRODUCED BY ANY MEANS WITHOUT THE WRITTEN CONSENT OF SEON DESIGN.
3
2
1
4
6
5
Cable Notch
No. 10
Screws
(2.00”)
No. 10
Screw
(1.25”)
Alignment
Peg
NOTE
Take care to ensure all screws are perpendicular to
the camera base.
Step 6: Replace Camera Dome
1. Fit the dome onto the base, ensuring the rubber IR boot around the camera lens is rmly pressed against the inside of
the dome.
2. Use the security key to tighten the captive screws.
Step 2: Remove Camera Dome
1. Using the security key supplied with the camera, loosen the captive screws on the housing.
2. Lift the housing off of the base.
For improved image quality in forward-facing camera
applications (through the windshield), we recommend
the following procedure to disable infrared (IR) LEDs,
enable the external light sensor to automatically control
Day/Night modes, and turn off the Backlight setting:
1. Open the recorder’s on-screen display Camera
Advanced tab:
Conguration Record Camera
Camera Advanced
2. Click the tab for the camera you want to congure.
3. Click Set to display the camera conguration MAIN
MENU.
4. Use the up/down arrows to select option 5,
DAY&NIGHT (a triangle pointer appears to the left
of the option).
5. Use the left/right arrows to cycle through settings
until the B/W option appears in the right-hand
column.
6. Click Set to open the B/W menu.
7. Use the down arrow to select IR.
8. Click the left or right arrow to toggle the IR setting
(option 4) OFF.
9. Use the down arrow to select RETURN, then click
Set to re-display the main menu.
10. In the main menu, with the DAY&NIGHT option
selected, use the left or right arrow to cycle through
settings until the EXT option appears in the right-
hand column.
11. Use the up arrow to select option 3,
BACKLIGHT.
12. Use the left or right arrow to to cycle through
settings until OFF appears in the right-hand column.
13. When you’re done, use the up/down arrows to
select option 9. EXIT (SAVE & END), then click Set
to save your settings and close the menu.
14. Click Back repeatedly to exit Conguration menus.
Select DAY&NIGHT option
cycle to B/W setting
RETURN to DAY&NIGHT option
cycle to EXT setting
Open B/W menu
toggle IR OFF
Select BACKLIGHT option
cycle to OFF setting
Standard Installation
Installation with Shim Angle Mount
1. Ensure a rubber washer is in place over each of the mounting
screws.
2. Use the three No. 10 x 1” mounting screws supplied with the
camera to attach the camera to the vehicle.
Step 7: Conguration Settings for Forward-facing Applications
Step 5: Aim Camera
1. With a monitor connected to the recorder, power up the
system. The monitor should display the multiple camera views
once the recorder is powered up.
2. Double-click a camera to display it in full-screen mode.
3. Aim the camera by tilting and rotating as required.
