Safe Fleet C3W9PD03E User manual
C3W9PD
Quick Install Guide
For camera models:
C3W9PD03E, C3W9PD03E-G, C3W9PD04E, C3W9PD04E-G
© Safe Fleet | 2021 | All rights reserved | Part #: 700-1163 R3
Installation Environment
When installing your product, consider the
following:
• Electrical: Install electrical wiring carefully.
This should be done by qualied service
personnel. Always use a proper PoE
switch to power the camera.
• Ventilation: Ensure that the location
planned for the installation of the camera
is well ventilated.
• Temperature: Do not operate the camera
beyond the specied temperature,
humidity, or power source ratings. The
operating temperature of the camera is
between -40°C and +65°C.
• Servicing: Do not attempt to repair this
camera yourself. Any attempt to dismantle
this product, except as required for normal
installation, will negate the warranty and
may also result in injury. Refer all servicing
to qualied service personnel.
• Cleaning: Do not touch the lens with your
ngers. If cleaning is necessary, use a
clean soft cloth with isopropyl alcohol and
gently wipe the camera.
Package Contents
Check the package and contents for visible damage. If
any components are damaged or missing, contact the
Seon Service team and request an RMA (Return Material
Authorization).
Package contents:
• Camera
• Drill Template
• Torx Security Wrench
• Brush Guard
• Weatherproof cap for RJ45 connector
• Qty 4 - #10, 1” Mounting Screws
Cable Requirements
It is recommended that camera harnesses be purchased
directly from Safe Fleet. All network cabling must be
installed according to applicable codes and regulations.
Cable should be CAT5e or CAT6, stranded or solid, 24
AWG or better. Both ends must be terminated with male
RJ45 connectors and should conform to TIA/EIA-568-B
standards. Spliced cables are not acceptable.
Support
• Phone: 1.844.899.7366
• Email: PTsupport@safeeet.net
Service
If your C3W9PD Camera is to be returned for service, please call toll free 1.877.630.7366, or 1.844.899.7366,
and provide the model and/or serial# of your unit.
Ask for a Return Merchandise Authorization (RMA) number. An RMA# allows the Service Technicians to better
track your product when it comes in for service. Please show the RMA# on the outside of the package. ANY
PRODUCT SENT WITHOUT AN RMA# MAY BE REFUSED.
Documentation
Additional copies of this guide, along with other supporting documentation can be found on the Safe Fleet
Community:
• https://community.safeeet.net
Accessing the Camera Using a Web Browser
You can use a Web browser to access and congure the camera over an Ethernet connection. For a direct
connection to a single camera:
1. Using a Web browser, enter the camera’s IP address (refer to the table below). The Login dialog box
appears.
Note: Ensure that the Active X controls are enabled.
2. Enter your user name and password. Default user name is Admin and default password is 11111111.
3. Click Login. The Web browser window appears.
Warranty
For full warranty information, visit:
• www.seon.com/documents/Seon-Warranty.pdf
2002/96/EC (WEEE directive): This product cannot be disposed of as unsorted municipal waste
in the European Union. For proper recycling, return the product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated collection points, for more
information, see www.recyclethis.info.
2006/66/EC (battery directive): This product does not contain batteries.
Typical IP Addresses
The camera’s default static IP address is 172.30.1.1. When connected to the network switch or directly to a
recorder, the camera’s IP address is assigned based on the device and port:
Connected Device IP Address Range Connected Port IP Address
16-port Network
switch
(NS18POE16)
172.31.1.101 through
172.31.1.116
<01-16> Change the last 2
digits based the port
number. For example:
the address for the
camera connected
to switch port #8 is:
172.31.1.108
NH16 recorder
(directly to rear-panel)
172.31.1.141 through 172.31.144 IPCAM1 172.31.1.141
IPCAM 2 172.31.1.142
WIFI 172.31.1.143
Modem 172.31.1.144
TH8 recorder
(directly to rear panel)
172.31.1.141 and 172.31.142 HD Cam Expansion 1 172.31.1.141
HD Cam Expansion 2 172.31.1.142
Fold Here
Warning: Blocking the Ambient Light Sensor
Take caution when positioning the lens, ensuring that the ambient light sensor is always unobstructed
when the camera is fully assembled. An obstructed sensor will prevent the camera from working properly.
4. Finally, re-install the cover using the cover screws.
5
4
1
3
2
7
6
8
9
Mounting the Camera
1. Use the supplied template to mark out the
mounting area. Drill the screw holes on the
surface.
2. Loosen the cover screws to remove the cover
from the camera and x the mounting base to the
surface with the appropriate screws.
Improper mounting can potentially result in
water damage to the camera. Please see the
Warning on the back page of this Guide.
3. Loosen the adjusting screw to adjust the pan, tilt,
and rotation angle, then re-tighten the screw.
Camera Components
1. Cover
2. Bubble
3. IR
4. Base
5. Lens
6. BNC cable
7. Camera Sealing Gasket
8. Ethernet RJ45 cable
9. Reset button
Important: Positioning the Lens
The ambient light sensor must be pointed downwards (or at the “6:00” position) when positioning the lens.
If the sensor is facing up (or at the “12:00” position), then the image will be upside-down.
Important: Camera Sealing
Keep the camera sealing gasket clear of any
debris and/or cables prior to installing the lid
to ensure a reliable seal. Also, take care not to
damage the gasket during installation.
Do not use sealant or silicone at the camera base
or along the seam between the lid and base.
Do not allow paint inside the gasket cavity or the
camera housing – mask off the gasket cavity
and all inside parts if painting the lid and base
separately.
WARNING: Ensure mounting screws do not pinch or obstruct the base plate gasket
The gasket running along the mounting base prevents water from seeping inside the camera, which
may damage internal components. To avoid compromising the gasket, install the mounting screws in
accordance with the following conditions:
• Oversized screw heads – we recommend using the supplied #10, 1” mounting screws. While this suits
most installations, different-sized screws may be required for specic vehicles. If you use a different-
sized screw, you must ensure the screw head does not contact the base plate gasket.
• Drilling/screw angle – when fully-inserted, the screw heads must sit ush with the countersunk holes in
the mounting base. Do not drill/thread the mounting screws at an angle or off-center, as this can pinch or
obstruct the base plate gasket.
This manual suits for next models
3
Other Safe Fleet Security Camera manuals
