Safe Fleet SEON HD1Q User manual

HD1Q Dome Camera
Quick Install Guide
© Seon Design Inc. | May 2017 | All rights reserved.
www.seon.com Part Number: 700-1084 R2
Installation Kit Contents
The HD1Q camera with IR is designed for interior use only. You’ll nd in this kit the following
components:
• 1 HD1Q camera, including dome, gasket, and connector cable
• 3 x No. 10 screws with washers (1”length)
• 1 Security key
• 1 Quick Install Guide
• 1 Drilling template (Part #: 700-1090)
WARNING: Cable Compatibility
This camera requires a special Analog High Denition (AHD) cable - as indicated by a blue band
in front of the connectors. The AHD cable is not included with the camera kit. If you require an
AHD Cable, please contact our customer service department to place an order.
NOTES:
MATERIAL: , ## GAUGE.
BEND RADIUS 0.8mm UNLESS OTHERWISE SPECIFIED.
BEND ANGLES 90 UNLESS OTHERWISE SPECIFIED.
FINISH:
B
C
D
1
2
A
B
A
C
D
3
4
5
File Last Saved Date: May-11-17 9:22:11 AM
File Name: 720P_AHD_3D drawing
6
TOLERANCES ARE:
REVISION
DIMENSIONS ARE IN MM
UNLESS OTHERWISE NOTED
NO DECIMAL PLACES
1 DECIMAL PLACE
2 DECIMAL PLACE
ANGLES
ARENA Tracking:
ENG:
DRAWN:
DATE APPROVALS
SEON DESIGN INC.
111 - 3B Burbidge St.
Coquitlam, BC
Canada V3K 7B2
TEL: [phone]
FAX: [phone]
MANUFACTURING DESCRIPTION:
PART NUMBER:
SHEET
SIZE
A
1 of 3
SHEET:
THIRD ANGLE PROJECTION
COPYRIGHT SEON DESIGN INC., ALL RIGHTS RESERVED. THIS DOCUMENT MAY NOT BE DISCLOSED, OR REPRODUCED BY ANY MEANS WITHOUT THE WRITTEN CONSENT OF SEON DESIGN.
3
2
1
4
6
5
Specications
Power Consumption 1 W (IR o); 2 W (IR on)
Operating Voltage Range 12 VDC ± 10% (powered by DVR)
Operating Temperature Range -4 to 122ºF (-20 to 50ºC)
Resolution 720p
Infrared LED Lamps 12 LEDs (5mm)
Minimum Illumination Color: 0.1 lux (F2.0)
B&W, IR LED on: 0 lux
Enclosure Size Diameter : 3.74”(95 mm)
Height: 2.64” (67 mm)
Enclosure Material Solid aluminum alloy
Dome Impact-resistant polycarbonate, anti-glare,
scratch-resistant hardcoating, UV protected
Connector Cable Length 12” (30 cm)
Weight 0.52 lbs (0.24 kg)
Support
Routine Maintenance
Most liquid cleaners or graphite gel can be used to clean your camera enclosure. Do not use
abrasive cleaners that can scratch the window and reduce visibility of the camera.
Replacing Damaged Housing
If the camera housing or dome is damaged or scratched, order a replacement part from Seon. To
remove and replace the housing, follow the steps in Step 3 and Step 6.
Service
If your HD1Q Series Dome Camera is to be returned to Seon Design for service, please call toll
free 1-877-630-7366, or 604-941-0880, and provide the model and/or serial number of your
unit. Ask for a Return Authorization (RA) number. An RA number allows the Service Technicians
to track your product when it comes in for service. Please display the RA number on the outside
of the package. ANY PRODUCT SENT TO SEON DESIGN WITHOUT AN RA NUMBER WILL BE
RETURNED.
Warranty
For full warranty information, go to www.seon.com/warranty.html.
Documentation
Copies of this guide can be found online at https://community.seon.com
Information in this guide is subject to change without notice.

Step 1: Choose Camera Location
1. Determine the location for mounting the camera.
a. Choose a solid surface to minimize vibration
b. Choose a location away from access panels, hatches, or doors which may block the
camera view
c. Choose a location away from heat sources
d. Cameras are usually installed with the cabling running inside the wall panels.
2. Use the supplied drilling guide template to mark the cable (7/8”) and screw (5/32”) holes on
the panel.
3. Use a step-bit to drill the cable hole, and regular bits for the screw holes.
Step 2: Connect Camera to DVR
1. Connect the camera cable to the extension cable through the panel cable hole.
Important: ensure the extension cable has a blue band in front of the connectors, indicating
it is AHD-compatible.
2. Connect the extension cable’s 2x3 Micro-Fit connector to the DVR.
Step 3: Remove Camera Dome
1. Using the security key supplied with the camera, loosen the captive screws on the housing.
2. Lift the housing o of the base.
Step 4: Install Camera
Use the three No. 10 x 1" mounting screws supplied with the camera to attach the camera to the
vehicle.
Step 5: Aim Camera
1. With a monitor connected to the DVR, power up the system. The monitor should display the
multiple camera views once the DVR is powered up.
2. Double-click a camera to display it in full-screen mode.
3. Aim the camera by tilting and rotating as required.
Step 6: Replace Camera Dome
1. Fit the dome onto the base, ensuring the foam IR boot around the camera lens is rmly
pressed against the inside of the dome.
2. Use the security key to tighten the captive screws.