Safe Fleet CMD1004E User manual

CMD1004E Exterior
Dome Camera
Quick Installation Guide
© Seon Design Inc. | 2020 | All rights reserved. Part Number: 700-1031 R2
Installation Kit Contents
• 1 Exterior Dome camera, base, and 4 M4 0.7x 1.0mm screws
• 4 #8x 3/4” Phillips screws
•1Torxkey
• 1 Quick Installation Guide
• 1 Drilling template
• 1 Base gasket
Choose Camera Location
Determine the location for mounting the camera. Select a flat location
to minimize moisture leakage into the vehicle. Cameras must be
installed with the cabling running inside the wall panels.
Install the Camera Base
1. Use the supplied Surface Type mounting template to mark the cable
(11/16”) and screw (1/8”) holes on the panel.
2. Use a step-bit to drill the cable hole, and regular bits for the screw
holes.
3. Apply the gasket to the camera base.
4. Pull the camera extension cable from the DVR to the camera
location.
5. Use the four supplied #8 x 3/4" Phillips screws to install the camera
base to the vehicle surface.
Open the Camera Assembly
1. Use the supplied Torx key to loosen the screw on the camera bezel.
2. Unthread the bezel from the camera assembly.
3. Remove the bezel and the camera dome from the camera assembly.
4. Connect the 2x3 microfit cable from the camera assembly to the
extension cable.
5. Pull the connected cabling back into the bus.
Attach the Camera to the Base
Screw the camera assembly to the mounted camera base using the
four supplied M4 0.7x10mm screws.
CAUTION: Vehicle Leakage Risk
For outdoor installations, if a flat surface is not available, seal
the mounting holes under the base of the camera after
installation.

Aim the Camera
To get the required video image, adjust the camera‘s rotation, pan, and tilt
settings using the adjustment controls and the DVR monitor video output.
Rotation: depending on how the camera is mounted, grip the tilt
screws and rotate the camera assembly to ensure the camera shows
a level view.
Pan: grip the camera gimbal while holding a finger or thumb against
the tilt screwmount and twist it to find the required view.
Tilt: loosen the tilt adjustment screws until the camera can tilt.
Tighten the tilt screws after adjustments are complete.
Do not adjust tilt after tightening screws.
Do not adjust any other screws.
Close the Camera
1. Replace the dome and bezel on the camera assembly.
2. Use the supplied Torx key to tighten the security screw on the
camera bezel.
Specifications
Routine Maintenance
Most liquid cleaners or graffiti gel can be used to clean your camera
enclosure. Do not use abrasive cleaners that can scratch the window and
reduce visibility of the camera.
If the window in your camera is damaged or scratched beyond use, order
a replacement window from your camera distributor.
Replacing a Damaged Dome
1. If the camera dome is damaged or scratched, order a replacement
bezel and dome assembly from your camera distributor.
2. To remove and replace the bezel and dome, follow the steps in Open
the Camera Assembly and Close the Camera.
Service & Support
If your CMD Exterior Dome Camera is to be returned for service, please
contact the Safe Fleet Technical Support team, provide the model and/or
serial number of your unit, and ask for a Return Merchandise
Authorization (RMA) number.
An RMA number allows the support team to better track your product
when it comes in for service. Please show the RMA number on the
outside of the package.
ANY PRODUCT SENT TO SAFE FLEET WITHOUT AN RMA NUMBER
MAY BE REFUSED!
Documentation & Warranty
Additional copies of this guide, along with other documentation and the
product warranty can be found on the Safe Fleet Community Web site:
https://community.safefleet.net
Technical Support
2002/96/EC (WEEE directive): This product cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling,
return the product to your local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collection points, for more
information, see www.recyclethis.info.
2006/66/EC (battery directive): This product does not contain batteries.
Power Consumption 1.68 W (Max)
Operating Voltage Range 7 to 18 VDC (powered by DVR)
Operating Temperature Range - 4 to 158°F (-20 to 70°C)
Horizontal resolution 800 TV Lines
Enclosure Size Diameter: 3.125” (80 mm)
Height: 2.625" (67 mm)
Enclosure Material Solid aluminum alloy
Connector Cable Length 12” (30 cm)
Phone: [phone]
(Mon.-Fri., 7:00am-7:00pm EST)
Email: PT[email protected]