Safire SF-MNT24 User manual
USER MANUAL
CCTV 4n1
PROFESSIONAL
MONITOR
Important information..................................................................
Safety warning.................................................................................
Notes....................................................................................................
Introduction to the product........................................................
Product appearance.......................................................................
Performance feature......................................................................
Connecting external device........................................................
Illustration of the main menu.....................................................
Main menu.........................................................................................
PC menu.............................................................................................
Audio menu......................................................................................
Picture menu....................................................................................
Function menu................................................................................
OSD menu.........................................................................................
Geometry menu..............................................................................
Channel selection...........................................................................
The way of cleaning.......................................................................
Trouble shooting............................................................................
Trouble shooting ways..................................................................
2
2
3
4
4
4
5
5
5
7
7
7
8
8
8
9
9
9
9
To use the product safely and rightly and to keep users from suering hurt or property loss, please
observe the following safety precautions when installing, using and maintaining.
Please read this handbook before operating the product and keep the handbook for future refer-
ence.
• Notice and observe all the warnings and illustration.
• Do not adjust, maintain or modify if you don’t have corresponding qualications.
• Do not open or remove the rear cover, box or cover board of the product. Please contact the
dealer or after-sales service center when needing internal checking, adjustment and main
taining.
• Do not place article on the product. The product might be damaged if foreign matters enter
the internal unit.
• Do not tread or squeeze the power line, especially on the plug, outlet or the place where the
cable extends out of the product.
• Do not put the product in inammable or corrosive gaseous environment, which might cause
re or damage the product. Putting the product in inammable gas is easy to cause danger
ous explosion.
• Please cut o power or the connecting line immediately if there is smoking, o-odour or
abnormal noise. Contact the after-sales service center to maintain after arming there is no
more smoking or o-avor. It might cause re if it is used without maintaining.
• Only qualied servicemen can maintain. If the product gets any kind of damage, such as
damage to plug, splash or foreign matter into the facility, exposed to rain or humidity, not
able to function or dropped from the high, please maintain it immediately.
• Do not expose the product to the rain or chemicals. If the product is moist, please dry it
before turn on the power.
• Turn o the power when clean the product.
• Installment of unsuitable facility might cause the fall of the facility or other accidents. Fasten
the screw of every component when installing.
• Do not touch the xed component inside the facility, otherwise it might cause damage to
people or to the facility.
• Be careful when maintaining inner body even if the power is cut o. Some facilities are
equipped with UPS, and they can continue to supply power which is dangerous to people
after the power is cut o.
SAFETY INFORMATION
To use the product safely and rightly and to keep users from suering hurt or property loss, please
observe the following safety precautions when installing, using and maintaining.
Please read this handbook before operating the product and keep the handbook for future refer-
ence.
• Notice and observe all the warnings and illustration.
• Do not adjust, maintain or modify if you don’t have corresponding qualications.
• Do not open or remove the rear cover, box or cover board of the product. Please contact the
dealer or after-sales service center when needing internal checking, adjustment and main
taining.
• Do not place article on the product. The product might be damaged if foreign matters enter
the internal unit.
• Do not tread or squeeze the power line, especially on the plug, outlet or the place where the
cable extends out of the product.
• Do not put the product in inammable or corrosive gaseous environment, which might cause
re or damage the product. Putting the product in inammable gas is easy to cause danger
ous explosion.
• Please cut o power or the connecting line immediately if there is smoking, o-odour or
abnormal noise. Contact the after-sales service center to maintain after arming there is no
more smoking or o-avor. It might cause re if it is used without maintaining.
• Only qualied servicemen can maintain. If the product gets any kind of damage, such as
damage to plug, splash or foreign matter into the facility, exposed to rain or humidity, not
able to function or dropped from the high, please maintain it immediately.
• Do not expose the product to the rain or chemicals. If the product is moist, please dry it
before turn on the power.
• Turn o the power when clean the product.
• Installment of unsuitable facility might cause the fall of the facility or other accidents. Fasten
the screw of every component when installing.
• Do not touch the xed component inside the facility, otherwise it might cause damage to
people or to the facility.
• Be careful when maintaining inner body even if the power is cut o. Some facilities are
equipped with UPS, and they can continue to supply power which is dangerous to people
after the power is cut o.
• Please put the facility in at, stable and draughty place and avoid direct sunlight, high tem
perature, humidity, dust and corrosive gas.
• If the product is installed on the wall, please make sure the wall’s load bearing is enough. To
avoid falling and hurt people, install according to the illustration.
• The LCD might get nebulized when the temperature variation is big, which will cause image
distortion or decay of color. Wait for a moment (with power on) and the nebulization will
disappear.
• Do not block up the ventilation opening. Install the facility according to this handbook.
• Do not install the facility near any heat source such as radiator, heat register or stove.
• Do not use unqualied connecting lines, which might cause equipment failure.
• Do not press, stretch or heat the connecting line, which might cause damage to it.
• Please rmly grasp the plug of the connecting line when inserting and drawing. Pulling the
connecting line emphatically might cause damage to it.
• Cut o power and the connecting line immediately and contact the after-sales service center
if the facility or the connecting line is damaged for some reason. Continuing using without
maintaining might cause smoking or o-avor.
• Do not hang or shin on the facility, which might cause the facility to fall, upset or damaged
and cause hurt to people. Be more careful when there are kids near the facility.
• Please cut o power for safety if not using the facility for a long time.
• Do not let the connecting line get squeezed by the wall or buckle, pull or twine the connect
ing line overly.
• Make sure the power and the connecting line are cut o when moving the facility.
• Keep the facility from getting collided, which might cause equipment failure.
Please put the facility in at, stable and draughty place and avoid direct sunlight, high tem
perature, humidity, dust and corrosive gas.
• If the product is installed on the wall, please make sure the wall’s load bearing is enough. To
avoid falling and hurt people, install according to the illustration.
• The LCD might get nebulized when the temperature variation is big, which will cause image
distortion or decay of color. Wait for a moment (with power on) and the nebulization will
disappear.
• Do not block up the ventilation opening. Install the facility according to this handbook.
• Do not install the facility near any heat source such as radiator, heat register or stove.
• Do not use unqualied connecting lines, which might cause equipment failure.
• Do not press, stretch or heat the connecting line, which might cause damage to it.
• Please rmly grasp the plug of the connecting line when inserting and drawing. Pulling the
connecting line emphatically might cause damage to it.
• Cut o power and the connecting line immediately and contact the after-sales service center
if the facility or the connecting line is damaged for some reason. Continuing using without
maintaining might cause smoking or o-avor.
• Do not hang or shin on the facility, which might cause the facility to fall, upset or damaged
and cause hurt to people. Be more careful when there are kids near the facility.
• Please cut o power for safety if not using the facility for a long time.
• Do not let the connecting line get squeezed by the wall or buckle, pull or twine the connect
ing line overly.
• Make sure the power and the connecting line are cut o when moving the facility.
• Keep the facility from getting collided, which might cause equipment failure.
Notes
• Please put the facility in at, stable and draughty place and avoid direct sunlight, high tem
perature, humidity, dust and corrosive gas.
• If the product is installed on the wall, please make sure the wall’s load bearing is enough. To
avoid falling and hurt people, install according to the illustration.
• The LCD might get nebulized when the temperature variation is big, which will cause image
distortion or decay of color. Wait for a moment (with power on) and the nebulization will
disappear.
• Do not block up the ventilation opening. Install the facility according to this handbook.
• Do not install the facility near any heat source such as radiator, heat register or stove.
• Do not use unqualied connecting lines, which might cause equipment failure.
• Do not press, stretch or heat the connecting line, which might cause damage to it.
• Please rmly grasp the plug of the connecting line when inserting and drawing. Pulling the
connecting line emphatically might cause damage to it.
• Cut o power and the connecting line immediately and contact the after-sales service center
if the facility or the connecting line is damaged for some reason. Continuing using without
maintaining might cause smoking or o-avor.
• Do not hang or shin on the facility, which might cause the facility to fall, upset or damaged
and cause hurt to people. Be more careful when there are kids near the facility.
• Please cut o power for safety if not using the facility for a long time.
• Do not let the connecting line get squeezed by the wall or buckle, pull or twine the connect
ing line overly.
• Make sure the power and the connecting line are cut o when moving the facility.
• Keep the facility from getting collided, which might cause equipment failure.
Please put the facility in at, stable and draughty place and avoid direct sunlight, high tem
perature, humidity, dust and corrosive gas.
• If the product is installed on the wall, please make sure the wall’s load bearing is enough. To
avoid falling and hurt people, install according to the illustration.
• The LCD might get nebulized when the temperature variation is big, which will cause image
distortion or decay of color. Wait for a moment (with power on) and the nebulization will
disappear.
• Do not block up the ventilation opening. Install the facility according to this handbook.
• Do not install the facility near any heat source such as radiator, heat register or stove.
• Do not use unqualied connecting lines, which might cause equipment failure.
• Do not press, stretch or heat the connecting line, which might cause damage to it.
• Please rmly grasp the plug of the connecting line when inserting and drawing. Pulling the
connecting line emphatically might cause damage to it.
• Cut o power and the connecting line immediately and contact the after-sales service center
if the facility or the connecting line is damaged for some reason. Continuing using without
maintaining might cause smoking or o-avor.
• Do not hang or shin on the facility, which might cause the facility to fall, upset or damaged
and cause hurt to people. Be more careful when there are kids near the facility.
• Please cut o power for safety if not using the facility for a long time.
• Do not let the connecting line get squeezed by the wall or buckle, pull or twine the connect
ing line overly.
• Make sure the power and the connecting line are cut o when moving the facility.
• Keep the facility from getting collided, which might cause equipment failure.
Thank you for buying this CCTV Display. We wish you to enjoy this product in the next few years. The
power dissipation is low no matter in viewing mode or standby mode, which means you make
contribution to energy saving. We are introducing the function of the product here and we hope it
can enrich your usage experience.
Full HD LCD panel with top-ranking video process chip, enhancing the effect of display of
high-definition images. The functions such as low power dissipation, dust prevention, moisture
protection and shock resistance effectively lengthen the service life of CCTV Display
• Supports 3D comb-filter and 3D de-interlace.
• Low energy consumption, long service life.
• High contrast ratio and high luminance.
• Automatically eliminates ghosting.
• Rapid response times, no trailing image.
• Thin and light.
• Support TVI & AHD &CVI 1080P camera display.
Introduction to the product
Product appearance
Performance feature
Please connect the monitor to external devices according to the following I/O interface list, and
choose corresponding signal incoming channel.
A. BNC IN: CVBS input
B. AUDIO IN: Stereo Audio input
C. VGA IN: VGA input
D. HDMI IN: HDMI input
E. USB: For Service (Firmware Update).
F. HD IN: AHD & TVI & CVI&CVBS input
G. HD OUT: AHD & TVI & CVI & CVBS output
Aenon
●Please cut othe power of the external device and this product to make sure the
connecon is normal.
Connecting external device
Main menu
Press the menu button on the bottom left of the screen, and the main menu displayed on the
screen. The submenus of the main menu: PC menu, Audio menu, Picture menu, Function menu,
OSD menu and Geometry menu.
Press the menu button to choose the submenus. The menu chosen will show a lit wireframe, and
press button to move among the secondary menus of the submenu.
A. “Source” button
• Press the button to display all the signal channel menus.
B. “Upward” button
• Press the button to move the cursor to the needed function.
• Press the button to choose function OSD menu.
C. “Downward” button
• Press the button to move the cursor to the needed function.
• Press the button to choose function OSD menu.
D. “Rightward” button
• Press the button to move the cursor to the needed function.
• Press the button to choose function OSD menu.
E. “Leftward” button
• Press the button to move the cursor to the needed function.
• Press the button to choose function OSD menu.
F. “Menu” button
• Press the button to display the OSD main menu.
• Choose an affirming button in OSD.
G. “Power” button
• Press the button to turn on or turn off the displayer.
(7Key)
(5Key)
Illustration of the main menu
Audio menu can set bass, treble, balance, sound mode. Press button to adjust, press button
to move, press menu button to exit.
Picture menu can set contrast, brightness, hue, saturation, sharpness, color temp, scale, overscan
and picture mode. Press button to adjust, press button to move, press menu button to exit.
PC menu can set contrast, brightness, color temp and scale. Press button to adjust, press
button to move, press menu button to exit.
PC menu
Audio menu
Picture menu
OSD menu can sleep timer, auto sleep, language, H-position, V-position, duration, transparency and
reset defaults. Press button to adjust, press button to move, press menu button to exit.
Geometry menu can set H-position, V-position, clock, phase and auto adjust. Press button to
adjust, press button to move, press menu button to exit.
Function menu can set noise reduction and DLC. Press button to adjust, press button to
move, press menu button to exit.
Function menu
OSD menu
Geometry menu
“Source” menu can select channel, the options include VGA, HDMI, BNC, CAM. Press button to
select, press menu button to exit.
1. Please wipe dust and other particles with clean downless mull.
2. If it is still not clean, please smear diluent neutral cleaner free from brightener on the clean down-
less mull and wipe with it. Wipe dry with a dry mull after cleaning it.
3. Rubbing or knocking the housing with fingernails or other hard objects might cause scratch.
Before consulting service staff, please find out the possible reason for the problem and the possible
solution according to the following chart.
Before consulting service staff, please find out the possible reason for the problem and the possible
solution according to the following chart.
Channel selection
The way of cleaning
Trouble shooting
Trouble shooting ways
Phenomenon
Handling method
1
2
3
4
5
6
7
8
9
10
11
No image or sound
⊕⊕⊕⊕⊕⊕
Inferior sound, normal image
⊕⊕⊕⊕⊕
Inferior image
，
normal
sound
⊕⊕⊕⊕⊕⊕
Poor signal
⊕⊕⊕⊕⊕
Vague image
⊕⊕⊕⊕
Double image
⊕⊕⊕⊕
Interfering lines in image
⊕⊕⊕⊕
Twisty image
⊕⊕⊕⊕
Poor signal
⊕⊕⊕⊕⊕⊕
Rung stripe in image
⊕⊕
Image vertically scrolls
⊕⊕⊕⊕
Inferior color
⊕⊕⊕⊕⊕⊕⊕⊕
No color
⊕⊕⊕⊕⊕
Processing Method
1
Alter to another channel or signal path.
2
Check whether the signal line is connected.
3
Check whether the signal line is connected.
4
Might be disturbed by other electric appliance.
5
Adjust �ine tuning setting.
6
Adjust luminance setting.
7
Adjust contrast ratio setting.
8
Adjust color setting.
9
Check whether the system is set rightly.
10
Check whether the power is on.
certificate of approval
Inspector
：
Inspector date：
The product accords with the technical criteria and is allowed to sell
Table of contents
