Saftronics PC10 User manual
PC10
Relay Output Card
Saftronics,Inc.
5580 Enterprise Pkwy., Ft.Myers, FL 33905
Telephone:(941)693-7200
Fax:(941)693-2431
www.saftronics.com
CARDNO.100-0159-01
DOC.NO. 027-0159 11/01
www.saftr
o
ni
c
s.
com
efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
PAGE 2
SAFETY FIRST !
LETHAL VOLTAGES MAY BE PRESENT!
PLEASE READ THIS INSTRUCTION MANUAL THOROUGHLY BEFORE
ATTEMPTINGANYINSTALLATION,OPERATION,MAINTENANCEOR INSPEC-
TION. FAILURE TO FOLLOW THE RECOMMENDED PROCEDURES OR
CAUTIONSINTHISMANUALCOULDRESULTININJURYTOPERSONNELAND/
ORDAMAGETOEQUIPMENT.
CAUTION !
1. CHECKTHE NAME WRITTEN ON THE PRODUCTS AND INSURETHAT
THE PROPER PART HAS BEEN RECEIVED.
2. THOROUGHLYINSPECTTHEPART(S)FOR ANYDAMAGEDUETOSHIP-
MENTORHANDLING.
3. THE PART(S) MAY CONTAIN CMOS CHIPS AND CAN BE DAMAGED BY
STATICELECTRICITY.HANDLINGSHOULD BEIN ACCORDANCEWITH
INDUSTRYSTANDARDS.
4. BEFORE INSTALLING THE PART(S) TURN OFF ALL POWER TO THE
EQUIPMENTANDINSURETHECHANGE INDICATOR LAMPONTHE IN-
VERTER IS
OFF
.
LETHALVOLTAGES ARE PRESENT !
5. DONOTCONNECT ORDISCONNECTWIRINGWHILEPOWER IS
ON!
6. FOLLOWGOODSTANDARDWIRINGPRACTICESANDANYAPPLICABLE
CODESTHAT MAY APPLY.
PAGE 7
efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
WARNING!
Saftronics
manufacturescomponentpartsthatcanbeusedinawide
variety of industrial applications. The selection and application of
Saftronics
products remains the responsibility of the equipment de-
signer or end user.
Saftronics
accepts no responsibility for how it’s
products may be incorporated into the final design.
Under no circumstances should any
Saftronics
product be incorpo-
rated into any product or design as the exclusive or sole safety con-
trol.Without exception, all controls should be designed to dynami-
cally fault detect and fail safe under all circumstances. All products
designed to incorporate a component part manufactured by
Saftronics
, must be supplied to the end user with appropriate warn-
ingsandinstructions as tothesafeuse and operation. Anywarnings
provided by
Saftronics
must be passed through to the end user.
Saftronics
offers an express warranty only as to the quality of it’s
productsto conform to thecatalogspecifications.NOOTHERWAR-
RANTY,EXPRESS OR IMPLIED, IS OFFERED.
Saftronics
assumes
noliabilityfor anypersonalinjury,property damage,lossesorclaims,
arising out of the mis-application of it’s products.
PAGE 6 PAGE 3
Description
The100-0159-01 RELAY OUTPUT CARD,provides(2)relay formC outputsfor
the PC10 Inverter.It has “hard pins” to assemble directly to the PC10’s control
terminals and screw type output terminals.
Specifications
Output relays - Form C contacts: 120 VAC @ 0.5A / 24VDC @ 1.0A
Installation
Turn off all power to the equipment being worked on before attempting any
installation.Referring to the figure onpage 5 andin accordance withthe PC10
instruction manual, remove the protective cover.Insert the “hard pins” into
terminalsY2,CME, and CM of thePC10’s control terminalsandtighten.Connect
the pig-tail leads to terminals Y1 and P24 and replace the cover.This completes
the installation.
After applying power, parameters E20 for (K1) and E21 for (K2) are to be
programmedin accordancewith the tableon page4. Refer to the PC10manual
for further details.
efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
PC10RELAYINTERFACE
C
NC
NO
C
NC
NO
K1
K2
100-0159-01
PC10 INVERTER
Y2
Y1
CME
CM
P24
GNITTES LANGISTUPTUOLATIGID
0)NUR(gninnuRevirD
1 )RAF(lavirrAycneuqerF
2)TDF(noitceteDleveLycneuqerF
3 )VL(langiSnoitceteDegatlovrednU
4)D/B(ytiraloPeuqroT
5 )LT(gnitimiLeuqroT
6)FPI(eruliaFrewoPyratnemomretfatratseR
7 )LO(gninraWylraEdaolrevO
8)EFIL(mralAemiTefiL
9 )2RAF(2noitceteDleveLycneuqerF
PAGE 4 PAGE 5
efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
PC10RELAYINTERFACE
C
NC
NO
C
NC
NO
K1
K2
100-0159-01
PC10 INVERTER
Y2
Y1
CME
CM
P24
GNITTES LANGISTUPTUOLATIGID
0)NUR(gninnuRevirD
1 )RAF(lavirrAycneuqerF
2)TDF(noitceteDleveLycneuqerF
3 )VL(langiSnoitceteDegatlovrednU
4)D/B(ytiraloPeuqroT
5 )LT(gnitimiLeuqroT
6)FPI(eruliaFrewoPyratnemomretfatratseR
7 )LO(gninraWylraEdaolrevO
8)EFIL(mralAemiTefiL
9 )2RAF(2noitceteDleveLycneuqerF
PAGE 4 PAGE 5
efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
WARNING!
Saftronics
manufacturescomponentpartsthatcanbeusedinawide
variety of industrial applications. The selection and application of
Saftronics
products remains the responsibility of the equipment de-
signer or end user.
Saftronics
accepts no responsibility for how it’s
products may be incorporated into the final design.
Under no circumstances should any
Saftronics
product be incorpo-
rated into any product or design as the exclusive or sole safety con-
trol.Without exception, all controls should be designed to dynami-
cally fault detect and fail safe under all circumstances. All products
designed to incorporate a component part manufactured by
Saftronics
, must be supplied to the end user with appropriate warn-
ingsandinstructions as tothesafeuse and operation. Anywarnings
provided by
Saftronics
must be passed through to the end user.
Saftronics
offers an express warranty only as to the quality of it’s
productsto conform to thecatalogspecifications.NOOTHERWAR-
RANTY,EXPRESS OR IMPLIED, IS OFFERED.
Saftronics
assumes
noliabilityfor anypersonalinjury,property damage,lossesorclaims,
arising out of the mis-application of it’s products.
PAGE 6 PAGE 3
Description
The100-0159-01 RELAY OUTPUT CARD,provides(2)relay formC outputsfor
the PC10 Inverter.It has “hard pins” to assemble directly to the PC10’s control
terminals and screw type output terminals.
Specifications
Output relays - Form C contacts: 120 VAC @ 0.5A / 24VDC @ 1.0A
Installation
Turn off all power to the equipment being worked on before attempting any
installation.Referring to the figure onpage 5 andin accordance withthe PC10
instruction manual, remove the protective cover.Insert the “hard pins” into
terminalsY2,CME, and CM of thePC10’s control terminalsandtighten.Connect
the pig-tail leads to terminals Y1 and P24 and replace the cover.This completes
the installation.
After applying power, parameters E20 for (K1) and E21 for (K2) are to be
programmedin accordancewith the tableon page4. Refer to the PC10manual
for further details.
efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor
Table of contents
