
Hang Instructions at point of use! Please call SAGEWASH™ SANITIZER for extra sets of instructions!
PREPARING TO USE YOUR SAGEWASH™ SANITIZER!
1. Place HTH tablet in the tablet container. DO NOT IN ANY SITUATION REMOVE PLASTIC JACKET FOR
TABLET. The jacket is there to protect the operator from touching chlorine. Hand tighten tablet container to
hydro body. Tighten until snug ONLY!
2. Connect the male end of the water hose to the female quick connector.
3. Attach the SAGEWASH™ SANITIZER into the quick connector.
4. Make sure all fittings are secure.
5. Turn water on at water source and check for leaks.
6. Squeeze the Flow Control Handle’s trigger located on the SAGEWASH™ SANITIZER and check for leaks.
7. PLEASE NOTE: the Flow Control Handle’s trigger is equipped with a lock. Squeeze trigger and point down
to lock. Squeeze trigger and point up to release.
SANITIZING WITH YOUR SAGEWASH™ SANITIZER
REMEMBER TO PICK UP SOLID BIO-MATTER AND RINSE WITH
FRESH WATER BEFORE BEGINNING CLEAN UP!
1. Make sure work area is well ventilated.
2. Begin to disinfect target area. It is not necessary to OVERUSE
the solution.
3. After cleaning is done, turn off water spigot. Disconnect
SAGEWASH™ SANITIZER from hose, allowing it to drain over a
gutter/drain area, or mix with a gallon of water to make a disinfecting
solution. Once disconnected from hose, the discharging solution is
highly concentrated. Avoid contact with skin or clothes.
4. Wash down area where SAGEWASH™ SANITIZER was drained.
Failing to do this may leave calcium deposits on the floor. Set the
SAGEWASH™ SANITIZER, properly drained, in a cool, dry storage
area out of the reach of children.
WATER SUPPLY
Water flowing through the SAGEWASH™ SANITIZER will be chlorinated by the HTH chlorine tablet. The exact
amount of chlorine dispensed is influenced by the rate of flow, water pressure and the temperature of the water. It is
strongly recommended that the water pressure inside the SAGEWASH™ SANITIZER unit not exceed 70 psi. Higher
pressures may damage the unit. This includes water pressure surges (water hammer) that exceed 70 psi.
MAINTENANCE PERIODIC CLEANING
Under normal circumstances no maintenance is necessary beyond the replacement of HTH tablets. If dirty or
excessively mineralized water is used it may be necessary to periodically clean the inside of the sanitizer. Clean the
inside of the SAGEWASH™ SANITIZER unit with white vinegar once monthly. Chlorine naturally precipitates
contaminants in the water. Hydro seal and hose washers may need to be replaced periodically. See parts list to
replace.
STORAGE
Store tablets in a cool, dry, and well-ventilated area, away from heat or flame. DO NOT handle wet or partially used
tablets. Rotate tablet stock to insure maximum potency. Only store in original tablet packaging.
SAGEWASH™ SANITIZER WARRANTY
The original purchaser of a SAGEWASH™ SANITIZER (proof of purchase required) has a one year warranty. No
other guarantees are expressed or implied. SAGEWASH™ SANITIZER will repair or replace any unit that fails due to
material workmanship. This warranty does not include nozzles, quick connects, hose washers, hydro seals, etc.,
which are available and replaceable at www.sagesanitizingsystems.com
The manufacturer and distributor of SAGEWASH™ SANITIZER assume no responsibility for misuse, accidents or
damage caused by the operator of SAGEWASH™ SANITIZER.
SAGEWASH™ SANITIZER is protected by U.S. Patent #5,441,073 for additional information, contact:
SAGE SANITIZING SYSTEMS
Unit 4, Cheney Manor Industrial Estate, Swindon, Wilts, U.K. SN2 2UD
Telephone +44 (0) 1793 603487 Fax: +44 (0) 1793 603489
USA Toll Free: Tel: 1 866 264 8895 (Service) Tel: 1 866 264 8896 (Sales) Fax: 1 866 264 8897
www.sagesanitizingsystems.com
CAUTION: DRAIN AFTER EACH USE!
NOTE: Squeeze
trigger on Flow
Control Handle and
then tilt the
SAGEWASH™
SANITIZER back
(1) 45° then forward
(2) 45° until
completely drained