Sailor 6215 VHF DSC Guide

USER & INSTALLATION MANUAL
SAILOR 6215 VHF DSC

Thrane & Thrane A/S
SAILOR 6215 VHF DSC Radio
User and installation manual
Document number: TT98-128471-THR-C
Release date: February 3, 2010

Disclaimer
Any responsibility or liability for loss or damage in connection with the use of this
product and the accompanying documentation is disclaimed by Thrane & Thrane. The
information in this manual is provided for information purposes only, is subject to
change without notice and may contain errors or inaccuracies.
Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone
relying on this information should acquire the most current version e.g. from the Thrane
& Thrane Extranet at: http://extranet.thrane.com.
Thrane & Thrane is not responsible for the content or accuracy of any translations or
reproductions, in whole or in part, of this manual from any other source.
Copyright
© 2010 Thrane & Thrane A/S. All rights reserved. Printed in Denmark.
Trademark Acknowledgements
•SAILOR is a registered trademarks of Thrane & Thrane A/S.
• Other product and company names mentioned in this manual may be trademarks or
trade names of their respective owners.

iii
Safety warning 1
The following general safety precautions must be observed during all
phases of operation, service and repair of this equipment. Failure to comply
with these precautions or with specific warnings elsewhere in this manual
violates safety standards of design, manufacture and intended use of the
equipment. Thrane & Thrane assumes no liability for the customer's failure
to comply with these requirements.
RF exposure hazards and instructions
Your Thrane & Thrane radio set generates electromagnetic RF (radio
frequency) energy when transmitting. To ensure that you and those around
you are not exposed to excessive amounts of energy and thus to avoid health
hazards from excessive exposure to RF energy, all persons must be at least
3’ (0.9 m) away from the antenna when the radio is transmitting.
Warranty limitation
IMPORTANT - The radio is a sealed waterproof unit (classified IPX8). To
create and maintain its waterproof integrity it was assembled in a controlled
environment using special equipment. The radio is not a user maintainable
unit, and under no circumstances should the unit be opened except by
authorized personnel. Unauthorized opening of the unit will invalidate the
warranty.
Installation and service
Installation and general service must be done by skilled service personnel.

iv
Emergency calls
MM
MM
MAA
AA
AYY
YY
YDD
DD
DAA
AA
AYY
YY
Y
NANA
NANA
NAMEME
MEME
ME of the VV
VV
VEE
EE
ESS
SS
SSS
SS
SELEL
ELEL
EL in distress
CC
CC
CALAL
ALAL
ALLL
LL
LSS
SS
SIGNIGN
IGNIGN
IGN or other IDENIDEN
IDENIDEN
IDENTT
TT
TIFICIFIC
IFICIFIC
IFICAA
AA
ATT
TT
TIONION
IONION
ION
MM
MM
MMM
MM
MSS
SS
SII
II
I
(If the initial alert is sent by DSC)
PP
PP
POO
OO
OSS
SS
SITIT
ITIT
ITIONION
IONION
ION
given as ll
ll
latat
atat
atitit
itit
itudeude
udeude
ude and longitlongit
longitlongit
longitudeude
udeude
ude
or
If latitude and longitude are not known
or if time is insufficient,
in relation to a known geographical location
NANA
NANA
NA
TURETURE
TURETURE
TURE of distress
Kind of AA
AA
ASS
SS
SSS
SS
SII
II
ISS
SS
STT
TT
TANCANC
ANCANC
ANCEE
EE
E required
Any other useful INFINF
INFINF
INFOROR
OROR
ORMM
MM
MAA
AA
ATT
TT
TIONION
IONION
ION
MM
MM
MAA
AA
AYY
YY
YDD
DD
DAA
AA
AYY
YY
Y-M-M
-M-M
-MAA
AA
AYY
YY
YDD
DD
DAA
AA
AYY
YY
Y-M-M
-M-M
-MAA
AA
AYY
YY
YDD
DD
DAA
AA
AYY
YY
Y
This is
NANA
NANA
NAME-NAME-NA
ME-NAME-NA
ME-NAME-NAME-NA
ME-NAME-NA
ME-NAMEME
MEME
ME
CC
CC
CALAL
ALAL
ALLL
LL
LSS
SS
SIGNIGN
IGNIGN
IGN
or other IDENTIFICATION
MM
MM
MMM
MM
MSS
SS
SII
II
I
(If the initial alert is sent by DSC)
Use the HANDMICHANDMIC
HANDMICHANDMIC
HANDMICRR
RR
ROPOP
OPOP
OPHONEHONE
HONEHONE
HONE for voice calling
MM
MM
Makak
akak
ake sure sur
e sure sur
e suree
ee
e youryour
youryour
your VV
VV
VHFHF
HFHF
HF RR
RR
Radiadi
adiadi
adioo
oo
o ii
ii
is on Cs on C
s on Cs on C
s on CH1H1
H1H1
H166
66
6
LL
LL
Lifif
ifif
ift Ct C
t Ct C
t Covov
ovov
overer
erer
er
PP
PP
Prr
rr
ree
ee
ess
ss
ss RED Buttons RED Button
s RED Buttons RED Button
s RED Button
until acoustic and light-indication
becomes steady (more than 3 seconds)
SHIP‘s NAME:
CALLSIGN:
MMSI:
OWNOWN
OWNOWN
OWN IDID
IDID
ID
99-129558

v
Preface 2
Radio for occupational use
The SAILOR 6215 VHF DSC fulfils the requirements of the EC
directive 1999/5/EC, Radio and Telecommunications Terminal
Equipment and is intended for use in maritime environment.
SAILOR 6215 VHF DSC is designed for occupational use only and
must be operated by licensed personnel only.
SAILOR 6215 VHF DSC not intended for use in an uncontrolled
environment by general public.
SAILOR 6215 VHF DSC is designed for installation by a skilled
service person.
Manual overview
This manual has the following chapters:
• Introduction contains a description of the VHF radio.
•Operation explains how to make and receive VHF and DSC calls,
including how to use and set-up the channel scanning, the 2-
way loudhailer, fog horn external loudspeaker.
•Installation explains how to mount the VHF radio and how to
connect accessories and external equipment.
•Service & maintenance contains support information including
lists of accessories and a troubleshooting guide.

vi

vii
Table of Contents
Chapter 1 Introduction
VHF radio with DSC ............................................................ 1
Chapter 2 Operation
General use and navigation ...............................................6
VHF radio communication .................................................12
HI/LO transmission power ................................................ 18
Watch ................................................................................19
Scan .................................................................................20
Radio setup ......................................................................22
DSC calls ..........................................................................25
Phone book .......................................................................41
Loudhailer with talk-back .................................................44
Automatic foghorn ...........................................................45
Hailer and Fog horn setup ................................................ 47
Replay function ................................................................48
Chapter 3 Installation
Unpacking the SAILOR 6215 VHF DSC ................................49
Installing the VHF radio ....................................................50
Power, VHF antenna and external equipment .................. 57
System setup ....................................................................62
SAILOR 6201 Handset cradle (optional) .............................64

Table of Contents
viii
Chapter 4 Service & maintenance
Contact for support ...........................................................65
Maintenance ....................................................................65
Equipment and accessories .............................................. 71
Warranty .......................................................................... 71
App. A Technical specifications
App. B Maritime channels
App. C Declaration of conformity
Glossary .........................................................................................83
Index ........................................................................................ 85

1
Chapter 1
1111
Introduction
Introduction 1
VHF radio with DSC
SAILOR 6215 VHF DSC, your
new SAILOR VHF radio with
full DSC functionality, is
approved to R&TTE and is
waterproof to the IPx8 and
IPx6 standard. As part of the
required safety equipment,
use the SAILOR 6215 VHF
DSC in an emergency
situation. However the best
way to guarantee
functionality in an
emergency situation, is to
use the radio in daily communication on board.
The VHF radio is a simplex/semi duplex VHF radio. It is designed with an easy-
to-use menu-driven setup. You use the soft-keys to enter the desired
functions, you browse and select a setting using the right selection wheel
knob. The large display has red adjustable backlight which provides a good
visibility even at night and protects your night vision.
The VHF radio can replay the last 90 s of received voice. This is a useful
feature to minimize misunderstandings and to record messages when the
radio is unattended.
The VHF radio connects easily to external equipment like a 2-way loudhailer
and an external speaker. You can use the loudhailer as a 2-way on-board
communicator. The loudhailer also functions as a fog horn. You can select
from several programmed fog-horn patterns.
For a list of other accessories available for the SAILOR 6215 VHF DSC check
with your nearest distributor.

Chapter 1: Introduction
2 VHF radio with DSC
Controls on the front plate
1. Loudspeaker.
2. Four soft keys with function title in the display.
3. Quick selection key for channel 16 and the programmed preference
channel.
4. Large display.
5. Connector for Handmicrophone or handset.
6. Button for sending a DSC Distress alert.
7. Squelch control to mute background noise.
8. Replay button to play back up to 90 s voice message.
9. Volume wheel knob with key-press function for volume control and power
on/off.
10. Selector wheel knob with key-press function for changing the working
channel, navigating in menus in the display and backlight dimming.
2
13 4
6
57 9 10
8

Chapter 1: Introduction
VHF radio with DSC 3
1111
Introduction
SAILOR 6215 VHF DSC display
The picture shows the display
after start-up. The display holds
various fields of information,
depending on the currently
selected function.
1. Action line containing
information relevant for the
currently selected function.
2. Current working channel.
3. Functions you can select with the soft keys. If there are more than 3
functions in the list press the soft key MORE to display further functions.
4. Status and other values for the current state or VHF channel.
5. Service line containing current temporary information relevant for the
current channel or function.
For a detailed description of the information shown for each of the functions
available see the chapter Operation on page 5.
1 2
3 4
5
WATCH
CALL
US
DISTRESS/CALL
16
GPS Position HI/LO
MORE...

Chapter 1: Introduction
4 VHF radio with DSC

5
Chapter 2
2222
Operation
Operation 2
In this chapter you find detailed instructions and guidelines for:
•General use and navigation
•VHF radio communication
•HI/LO transmission power
•Watch
•Scan
•Radio setup
•DSC calls
•Phone book
•Loudhailer with talk-back
•Automatic foghorn
•Replay function
Note
Before using the VHF radio make sure that the VHF antenna, power
and other external equipment are connected properly. For
instructions see chapter Installation on page 49.

Chapter 2: Operation
6 General use and navigation
General use and navigation
Power on and speaker volume
The VHF radio has a dual-function on/off wheel knob for power
on/off and volume control.
• To power on the VHF radio press the on/off wheel knob.
• To power off the VHF radio, press and hold the on/off wheel
knob and follow the instructions in the display.
• To adjust the speaker volume, turn the volume wheel knob (clockwise =
louder, counter clockwise = softer, until muted). When adjusted to the
muted level is shown in the display.
Working channel, settings and dim function
The selector wheel knob has several functions:
• To select the working channel, turn the selector wheel knob.
• To browse and select settings, turn the selector wheel knob
and press for accept.
•Todim the backlight in the display until it is appropriate for the current
situation, i.e. to give comfortable night vision, press, hold and turn the
selector wheel knob (clockwise= more light).

Chapter 2: Operation
General use and navigation 7
2222
Operation
DSC and MMSI number
When the VHF radio is powered on for the first time, you must enter the
vessel’s MMSI number. Hereafter the MMSI number is briefly displayed after
power up. The MMSI is a unique, 9-digit identifier assigned to your ship.
Entering the MMSI number
When being prompted after power up enter the MMSI
number as described below:
1. Enter the 9 digits one by one by turning the
selector wheel knob to the desired digit, press the
selector wheel knob to accept the digit and
advance to the next digit.
To delete the previous digit press the soft key
BACK.
2. Press the soft key OK to confirm the entered MMSI number.
3. To leave without saving press the soft key CANCEL.
Important
The MMSI number must be programmed into the VHF radio to
use any DSC functionality. The radio will prompt for the MMSI
number at each power-up until the MMSI has been entered. An
error message is displayed when trying to initiate any DSC
function. However, you can use the radio in normal VHF mode.
Caution! Without a programmed MMSI number the
Distress button will not work!
Note
The MMSI number can be programmed by the operator once. If a
wrong number has been entered and stored, or if there is a
requirement to change it, contact your authorized dealer.
OK
BACK
CANCEL
No DSC/Distress
Enter MMSI:
MMSI MISSING
000000000

Chapter 2: Operation
8 General use and navigation
Once programmed, you can see the MMSI number
in the service line directly after start-up. The DSC
functionality is operational at any time.
The message NO DSC (NO MMSI) is shown in the
action line if the MMSI is not programmed.
Position and MMSI Information
To display position and MMSI information for the SAILOR 6215 VHF DSC radio,
do as follows:
1. Press the soft key POS. If it is not in the display, press the soft key MORE
until POS appears.
The display shows the current (latest) position (if a GPS is connected), the
position UTC and type, GPS Status and MMSI.
2. You can enter the position and UTC manually. Turn the selector wheel knob
to select the value you want to change. Then press and turn the selector
wheel knob to enter the current position or UTC time. The display shows
Man Position.
3. Press the soft key SAVE to save the new value.
4. After you have entered a value manually or overruled the GPS input, a soft
key UseGPS appears in the display if the GPS is available. Press this soft key
if you decide to use the data from the connected GPS.
5. Press the soft key EXIT to return to normal use.
If the GPS was present and then disappears a warning appears in the display
after 10 minutes. Follow the instructions on the screen.
16
HI/LO
WATCH
CALL
MORE
INT
MMSI NUMBER
219830067
GPS Position

Chapter 2: Operation
General use and navigation 9
2222
Operation
Speaker devices
The VHF radio can be equipped with the following speaking devices:
• SAILOR 6202 Handmicrophone with a PTT (Push To Talk) button.
• Handset with a microphone, ear piece and a PTT button. The volume in the
ear piece can be adjusted, for details see Controller setup on page 10.
• Loudhailer.
•Externalspeaker.
See Controller setup on page 10 for managing speaking devices.
Adjusting the squelch
With the Squelch control you can manually adjust and suppress
noise in order to optimize the quality of the received radio
communication.
• When hearing noise or an unwanted signal, turn the
squelch button clockwise until the speaker is muted.
Functions
The following functions are available from top-level standby:
Soft key Function
HI/LO Transmitter power, high or low
WATCH Dual or triple watch
CALL DSC calls
POS Current position from GPS, including UTC time and
MMSI number
ALERT Make a distress call, categories can be assigned

Chapter 2: Operation
10 General use and navigation
The functions of the SAILOR 6215
VHF DSC are accessed and set
using the four soft keys to the left
of the display. The current
function of a soft key is shown in
the display next to the soft key. For
some applications there are two control levels
•Atop level showing the current information and options for this
application. This can be on one page, or on several pages.
•Asetup screen showing the options you can configure for the specific
application.
Use the soft key MORE to display further applications.
Controller setup
In the CONTROLLER SETUP you set handset volume, external speakers and
display contrast. You can view the Software version and serial number.
To change a setting in the CONTROLLER SETUP, do as follows:
1. Press the soft key SETUP. If it is not in the display, press the soft key MORE
until SETUP appears.
2. Press the arrow soft key or to advance to CONTROLLER SETUP.
SCAN Scanning function
HAIL Loudhailer
FOG Fog horn
PBOOK Phone book
SETUP Setup pages for RADIO, HAILER/FOG, SYSTEM,
CONTROLLER and DSC
Soft key Function
4 soft keys
16
HI/LO
WATCH
CALL
MORE...
GPS Position
DISTRESS/CALL
INT