Salton SCI2009 Guide

1
WARRANTYAND INSTRUCTIONS
MODEL NO: SCI2009
SALTON CORDLESS STEAM IRON

2
Thank you for purchasing the SALTON Cordless Steam Iron. All SALTON appliances are
manufactured with the strictest standards to ensure safety, quality and reliability.
Please read this instruction manual carefully and familiarize yourself with your new steam iron, before using it
for the first time. Retain the manual for future reference.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the following:
1. Please read all instructions carefully before using the appliance for the first time.
2. Before connecting the appliance, check that the voltage indicated on the rating plate corresponds with the
mains voltage in your home.
3. Keep out of reach of children. This appliance is not intended for being used by young children or infirm
persons without supervision. Young children should be supervised to ensure that they do not play with the
appliance.
4. VERY IMPORTANT: To protect against the risk of electric shock, do not immerse appliance, plug or
cord set in water or other liquids. Do not use near washbasins or sinks. Ensure that the appliance does not
get wet (water splashes etc.) and do not use it with wet hands.
5. Use caution when using this iron. Do not touch hot surfaces as burns can occur from touching hot metal
parts. Always hold by the handle.
6. When you have finished ironing or when you leave the ironing for a short while:
Turn the Steam Button to position 0
Stand the iron upright
Disconnect the power base from the wall outlet.
7. Do not use the iron when it is damaged in any way. Do not operate the iron with a damaged cord or plug.
Do not replace the power cord or any other parts by yourself. Take the iron to the nearest authorized
service facility or to the shop where you bought it, as special tools are required for repair.
8. This appliance is intended for household use only. Do not use the appliance for anything other than its
intended purpose as this will result in the warranty becoming invalid.
9. Do not place the iron near or on a hot gas or electrical burner or in a heated oven.
10. Please use only genuine attachments supplied by an authorized Service-Dealer or the supplier.
11. Do not pull on the cord to disconnect from the power outlet. Always grasp the plug firmly and pull to
disconnect.
12. Always disconnect the iron from the power outlet when filling in water or when you remove the water
after use. Empty the iron after use. Do not store with water in the tank.
13. Do not allow the cord to touch the hot soleplate. Let the iron cool down completely before packing it
away. Pack the cord inside the power base when storing.
14. Never use an extension power cord that is not approved by an authorized and competent authority.
Please check that the cord is correctly wired and rated for its use.
15. The iron is for household use only. If appliance is to be used by a third party, please supply the instruction
manual with it.
16. No liability can be accepted for any damage caused by non-compliance with these instructions or any

3
other improper use or mishandling.
NOTE: Some parts of the iron have been slightly greased and as result the iron may smoke slightly when
switched on for the first time. Remove any protective films or stickers from the soleplate and the cabinet.
Clean the soleplate with a soft cloth. When using the iron for the first time, test it on an old piece of fabric to
ensure that the soleplate and water tank are completely clean.
HINTS BEFORE USE
1. Remove all the packaging material and protective labels from the soleplate and clean the iron’s
soleplate surface and vents as well as the water tank to remove manufacturing dust.
2. Unwind the mains lead from the power base and straighten it out.
3. Fill the iron with water (preferably distilled), set the iron onto the power base and plug in.
Note: If the iron is not placed onto the power base it cannot charge.
DESCRIPTION OF PARTS
CHOICE OF
WATER
1. This iron can be used with normal tap water.
2. If the water in your area is particularly hard, it is advisable to use distilled or de-mineralized water.
3. Do not use chemically de-scaled water or any other liquids for refilling.
HOW TO FILLWITH WATER
1. Unplug the iron from the wall outlet.
2. Turn the Steam Button to the OFF position and Temperature Control Dial to the MIN position.
3. Hold the iron handle, tilt the iron to a slope and fill in water through water inlet slowly.
4. Fill up to the MAX level of the water tank. Do not overfill.
Important: Remove the water after use. Do not store the iron with water in the water tank.

4
SETTING THE TEMPERATURE
1. Before setting the temperature, read the care instructions on the garment. If there are no hints for care of
the garment, then the table below may assist you. If the fabric consists of a combination of fibre types, you
must always select the lowest ironing temperature for a particular fibre type in the garment:
Temperature
Setting
Kind of Textile
Label
Better Ironing-methods
●
Synthetic
Dry ironing on the back and
pad of garment. Do not spray
water directly, or spot will
appear.
●
Silk
Dry ironing on the back of
garment
●●
Nylon
Dry ironing on the back of
garment, ironing collar,
sleeves, pocket
●●●
Wool
Do not use dry ironing.
●●●
Cotton
Steam Ironing, and Spraying
according to thick-thin and
fold crease of garment.
●●●
Linen
2. Insert the plug into the wall socket and stand the iron on the power base for charging.
3. Turn the temperature control dial to the correct temperature according to the type of
fabric being ironed (see pt 1).
4. The pilot light will turn off when the correct temperature has been reached.
The pilot light will switch on and off from time to time indicating that the selected temperature is being
maintained.
STEAM IRONING
1. Fill the iron as described above, plug in the power base and switch on.
2. Turn the temperature control dial to the “MAX”position.
3. Set the iron onto the power base and allow the iron to heat for 2 minutes.
Note: Please wait through 3 periods of the pilot light switching from “ON” to “OFF”.
4. Turn the Steam control button to the “Steam” position.
5. After using the iron for about 40 seconds, please turn the steam control to the “OFF” position, set the iron
onto the power base until the Pilot Light turns off, then you can use the steam again.
6.
BURST OF STEAM IRONING
This function can be used only at higher ironing temperatures and provides an extra burst of steam to remove

5
stubborn wrinkles.
1. Fill water into the iron as described above to the maximum mark.
2. Plug in the power base and switch “ON”.
3. Adjust the temperature control dial to the “MAX”position.
4. Set the iron onto the power base and allow the iron to heat for 2 minutes.
Note: Please wait through 3 periods of the pilot light switching from “ON” to “OFF”.
5. Make sure that the steam control button is in the “OFF” position and press the Burst of Steam button at
intervals of at-least 3 seconds.
6. Apowerful burst of steam will penetrate into the fabric assisting in removing wrinkles.
7. After using for about 25 seconds, place the iron back onto the power base until the pilot light turns “OFF”.
The Burst of Steam function can then be repeated.
Note: With conventional steam ironing, water may leak from the soleplate if a very low temperature has
been selected. If this happens, turn the temperature control dial to the advised position; steaming will
recommence as soon as the appropriate temperature has been reached.
DRY IRONING
The iron can be used as a dry iron even if there is water in the tank. Do not put water in the water tank when
the iron is to be used as a dry iron for a few hours at a time.
1. Adjust the temperature control dial to reflect the temperature indicated by the garment care instructions
and make sure the steam control button is in the “OFF” position. Insert the power cord into the wall
socket.
2. Set the iron onto the power base and allow the iron to heat for 2 minutes.
Note: Please wait through 3 periods of the pilot light switching from “ON” to “OFF”.
3. Remove the iron from the base and begin using.
5. When the iron is no longer hot enough, return it to the power base for re-charging. Continue to do this
throughout the ironing process.
6. After ironing, please turn the Temperature Control Dial to the “MIN”position. Pull the plug out, stand
the iron upright, and wait until the soleplate has cooled down completely before packing away for
storage.
SPRAY FUNCTION
This function can be used any time and is useful for use on heavily creased clothes and thicker fabrics. It is not
dependent on the temperature of the iron.
1. Fill water into the iron up to the “MAX” level of water tank.
2. Aim the spray nozzle at the garment.
3. Press the Spray Button.
VERTICAL STEAM IRONING
1. Hang the article to be steamed on a clothes hanger.

6
2. Follow instructions for steam ironing up to step 3.
3. Ensure that the Steam Control Button is in the OFF position.
4. Hold the iron vertically as close as possible to the fabric you wish to steam. Do not touch the fabric with
the soleplate.
5. Pull the fabric tight with your free hand.
6. Press the Burst of Steam Button repeatedly with intervals of at-least 3 seconds across the creased area.
7. After using for approx. 25 seconds, place the iron back onto the power base for re-charging.
8. You can then reapply vertical steam.
Note: When using vertical or burst of steam function, always ensure that there is sufficient water in the
tank.Allow for at-least 3 second intervals before repeating the steam function.
SELF-CLEANING
The self-cleaning feature cleans the inside of the soleplate, removing impurities. We recommend that this
feature is used every 5-10 days. By pushing the self-cleaning button a strong steam will be injected from the
soleplate, thus the iron can be cleaned from the inside to avoid the vents of the soleplate becoming blocked.
1. Set the Steam Control Button to the “OFF”position (no steam)
2. Fill the water tank to the 2/3 mark.
3. Set the Temperature Control Dial to “MAX”and put the iron onto the power base, allowing the iron
to heat/charge for 2 minutes.
4. Remove the iron from the power base and press the Self-Cleaning Button. Steam and impurities will
be emitted from the soleplate.
5. When the tank is empty, place the iron back on the power base and let the iron heat up again for 1-2
minutes to evaporate any remaining water in the tank.
CLEANING & MAINTENANCE
1. After using, first unplug the unit and allow it to cool down before cleaning.
2. Empty out the remaining water. Hold the soleplate away from you while doing this incase it is still hot.
WARNING: The contents of the water tank may also still be hot.
3. Wipe the soleplate with a soft wet cloth and keep it level and smooth avoiding metal-friction.
4. Scrub incrustation off the spraying nozzle with a toothpick.
5. Wash the inside of the water tank frequently. First fill with water, and then sway it from side to side
finally pouring out the water through the water opening.
6. Don’t use strong acid or alkali products on the iron as this may damage the frame and produce a colour
change to the body of the unit.
7. Do not use harsh abrasive cleaners or solvents when cleaning the iron.
8. Pour the water in the water tank out completely after using every time, then store it upright.

7
IF THE PLUG NEEDS CHANGING
1. Connect the Green/Yellow wire (Earth) to the terminal marked E
2. Connect the Blue wire (Neutral) to the terminal marked N.
3. Connect the Brown wire (Live) to the terminal marked L.
4. Fasten the grip cord securely.
5. If in doubt, please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED
Ensure that the voltage marked on the appliance corresponds with the supply voltage.
AFTER SALES SERVICE
This appliance is not user serviceable. If it is not working properly check the following:
1. You have followed the instructions correctly and carefully.
2. The plug fuse hasn’t blown.
3. The mains supply fuse/circuit breaker hasn’t blown/tripped.
4. If the appliance still doesn’t function, please consult your retailer. If the retailer is unable to resolve
the problem and you need to return the unit to the distributor, please proceed as follows:
Repack carefully into its original packaging.
Enclose your contact details (Name, address, contact telephone number).
Enclose an explanation of the problem you are experiencing with the appliance.
If the appliance is still under warranty, state where and when it was purchased and include
your proof of purchase (e.g. till receipt).
Return to the retailer where it was purchased, who will ensure that it is sent in to our service
department.
An estimate for the inspection/repairs will be sent to you should the unit be outside of the
warranty.
Spare parts can be obtained from our Spares Division. Please contact the Customer Service

8
Department on 011 490 9000 for a quote or further information.

9
PLEASE AFFIX YOUR PROOF OF PURCHASE/RECEIPT HERE
IN THE EVENT OF A CLAIM UNDER WARRANTY THIS RECEIPT MUST BE
PRODUCED.
W A R R A N T Y
1. Tedelex Trading (Pty) Limited (“Tedelex”) warrants to the original purchaser of this product (“the
customer”) that this product will be free of defects in quality and workmanship which under normal
personal, family or household use and purpose may manifest within a period of 1 (one) year from
the date of purchase (“warranty period”).
2. Where the customer has purchased a product and it breaks, is defective or does not work properly
for the intended purpose, the customer must notify the supplier from whom the customer bought the
product (“the supplier”) thereof within the warranty period. Any claim in terms of this warranty must
be supported by a proof of purchase. If proof of purchase is not available, then repair, and/or
service charges may be payable by the customer to the supplier.
3. The faulty product must be taken to the supplier's service centre to exercise the warranty.
4. The supplier will refund, repair or exchange the product in terms of this warranty subject to
legislative requirements. This warranty shall be valid only where the customer has not broken the
product himself, or used the product for something that it is not supposed to be used for. The
warranty does not include and will not be construed to cover products damaged as a result of
disaster, misuse, tamper, abuse or any unauthorised modification or repair of the product.
5. This warranty will extend only to the product provided at the date of the purchase and not to any
expendables attached or installed by the customer.
6. If the customer requests that the supplier repairs the product and the product breaks or fails to work
properly within 3 (three) months of the repair and not as a result of misuse, tampering or
modification by or on behalf of the customer, then the supplier may replace the product or pay a
refund to the customer.

10
7. The customer may be responsible for certain costs where products returned are not in the original
packaging, or if the packaging is damaged. This will be deducted from any refund paid to the
customer.
TEDELEX TRADING (PTY) LTD (JOHANNESBURG)
JOHANNESBURG TEL NO. [phone]
CAPE TOWN TEL NO. [phone]
DURBAN TEL NO. [phone]
www.amap.co.za