Sampo SME-32DL5 User manual

34” (32” Viewable) 4:3 SUPER FLAT TUBE
29” (27” Viewable) 4:3 PERFECTLY FLAT TUBE
USER MANUAL
MULTIMEDIA MONITOR

-3-
TABLE OF CONTENTS
1. WARNING AND CAUTION……………………………………………………………… 1
2. IMPORTANT SAFETY INSTRUCTION………………………………………………2-5
3. FCC STATEMENT………………………………..……………………………………… 6
4. SPECIFICATIONS……………………………………………………………………… 7-8
5. CONNECTING YOUR MONITOR……………….……………………………………… 9
6. LOCATION OF BUTTONS ON REMOTE CONTROL………………………………..10
7. LOCATION OF CONTROL (ON FRONT PANEL)…………..………….…………… 11
8. INSTALLATION……………………………………………………………..…………… 12
9. USING THE MONITOR’S ADVANCED FEATURES………………………..........13-21
10. POWER MANAGEMENT FUNCTION………………………………………………....21
11. TROUBLE SHOOTING………………………………………………………….……… 22

WARNING AND CAUTION
-4-
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MONITOR TO RAIN
OR MOISTURE.
HIGH VOLTAGE EXISTS ON THE CATHODE-RAY TUBE ANODE LEAD OF THIS
MONITOR. BEFORE SERVICING, DETERMINE THE PRESENCE OF HIGH VOLTAGE
BY CONNECTING THE H.V. METER BETWEEN THE ANODE OF CRT CAP AND
CHASSISONLY.
CAUTION:
1. Keep monitor away from excessive dust, high temperature, moisture or direct
sunlight.
2. Use well ventilated area and do not cover ventilation openings.
3. Unauthorized modification to this equipment, substitution or the use of an
unshielded connecting cable may cause excessive interference.
4. As an ENERGY STAR ®Partner, SAMPO CORPORATION has determined that this
product meets the ENERGY STAR®guidelines for energy efficiency .
5. If the picture display is in any way abnormal, disconnect from main power supply.
Check and ensure the installation is correct. Then reconnect the main power
supply.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR REAR)
DO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL

IMPORTANT SAFETY INSTRUCTION
-5-
Prior to using this product, please ensure that you have carefully read and
understood all the procedures outlined in this user’s manual.
1. Read all of these instructions.
2. Save these instructions for later use.
3. Follow all warnings and instructions marked on the product.
4. Disconnect from the main power supply before cleaning. Do not use liquid or
aerosol cleaners. Use only a slightly damp cloth for cleaning.
5. Do not use this product near water.
6. Do not place this product on an unstable cart, stand or table. The product may
fall, causing serious damage.
7. Slots and openings in the cabinet located at the back and underneath are
provided for ventilation. To ensure reliable operation of the product and to
protect it from overheating, these openings must not be blocked or covered by
placing the product on a bed, sofa, rug, or other similar surface. This product
should never be placed near or over a radiator or heat source. This product
should not be placed in an enclosed installation unless proper ventilation is
provided.
8. This product should be operated from the type of power source indicated on the
marketing label. If you are not sure of the type of power available, consult your
dealer or local power company.
9. This product is equipped with a 3-pin earthed plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is
a safety feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the purpose of the
grounding-type plug.
10. Do not place anything over the power cord. Do not locate this product where
the cord might cause potential injuries.

IMPORTANT SAFETY INSTRUCTION
-6-
11. If an extension cord is used with this product, ensure that the total ampere
ratings of the products connected to the extension cord do not exceed the
extension cord ampere rating. Also ensure that the total amperes of all
products connected to the mains outlet does not exceed 15 amperes.
12. Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a
risk of fire or electric shock. Never spill liquid of any kind on the product.
13. Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks.
Refer all servicing to qualified service personnel.
14. Disconnect this product from the main power supply and refer servicing to
qualified service personnel under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating instructions are
followed. Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the
product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a need for
service.

Wichtige Sicherheitshinweise
-7-
1. Bitte lesen Sie sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen.
Verwenden Sie keine Flüssig-oder Aerosolreiniger.
Am besten dient ein angefeuchtetes Tuch zur Reinigung.
4. Umeine Beschädigung des Gerätes zu vermeiden sollten
Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.
Ein Kippen oder Fallen könnte Verletzungen hervorrufen.
Verwenden Sie nur sichere Standorte und beachten Sie die
Aufstellhinweise des Herstellers.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor
Überhitzung schützt. Sorgen Sie dafür, daßdiese Öffnungen nicht abgedeckt
werden.
8. Beachten Sie beim Anschlußan das Stromnetz die Anschlußwerte.
9. Die Netzanschlußsteckdose mußaus Gründen der elektrischen
Sicherheit einen Schutzleiterkontakt haben.
10. Verlegen Sie die Netzanschlußleitung so, daßniemand darüber fallen kann.
Es sollte auch nichts auf der Leitung abgestellt werden.
11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
12. Wird das Gerät uber einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen.Somit wird im Falle einer
Überspannung eine Beschädigung vermieden.

Wichtige Sicherheitshinweise
-8-
13. Durch die Lüftungsäffnungen dürfen niemals Gegenstände oder
Flussigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw.
elektrischen Schlag auslösen.
14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprufen:
a -Netzkabel oder Netzstecker sind beschädigt.
b -Flussigkeit ist in das Gerät eingedrungen.
c -Das Gerät war Feuchtigkeit ausgesetzt.
d -Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e -Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f -Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. Den Orginalteilen
entsprechende Teile verwendet werden. Der Einsatz von ungeeigneten
Ersatzteilen kann eine weitere Beschädigung hervorrufen.
17. Wenden Sie sich mit allen Fragen die Service und Reparatur betreffen an Ihren
Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher.

FCC CLASS-B STATEMENT
-9-
IMPORTANT:
The equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in strict accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measure:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnected cables and shield power cords must be employed with
this equipment to insure compliance with the pertinent RF emission limits
governing this device.
Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment and invalidate the warranty.
NOTICE OF COMPLIANCE WITH CANADIAN INTERFERENCE-CAUSING
EQUIPMENT REGULATIONS
ThisClassBdigitalapparatusmeetsallrequirementsoftheCanadianInterference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.

SPECIFICATIONS:
-10 -
MULTIMEDIA MONITOR 34” (4:3) 29” (4:3)
1. Cathode ray tube
a. tube size 34 inch
(32 inch viewable) 29 inch (27 inch viewable)
b. Dot pitch H=0.8mm H=0.68mm(center)
c. Light transmission 35% typical 53.5% typical
2. Power
a. Input voltage 100 Vac ~ 240 Vac
60Hz / 50Hz 100 Vac ~ 240 Vac 60Hz / 50Hz
b. Input current 3A at 110Vac / 60Hz Max 3A at 110Vac / 60Hz Max
c. Power consumption
220 Watts(Max) 210 Watts(Max)
3. Input signal
Video signal
a. Type Analog Analog
b. Polarity Positive Positive
c. Amplitude RGB: 0.714 Vp-p
AV: 1Vp-p (with sync)
Y CB CR: 1Vp-p
(with sync)
RGB: 0.714 Vp-p
AV: 1Vp-p (with sync)
Y CB CR: 1Vp-p
(with sync)
d. Input impedance 75 ohms 75 ohms
e. Dot rate 75 MHz(Max.) 75 MHz(Max.)
Audio Signal
a. Type Analog Analog
b. Polarity 1.0Vp-p1.0Vp-p
c. Amplitude ≧10KΩ≧10KΩ
Horizontal sync
a. Type TTL TTL
b. Polarity Positive or negative Positive or negative
c. Input impedance 1K ohm(Min) 1K ohm(Min)
d. Frequency RGB: 31 KHz ~ 52 KHz
AV/Y CB CR:
15.734 KHz (NTSC)
15.625 KHz (PAL)
RGB: 31 KHz ~ 52 KHz
AV/Y CB CR:
15.734 KHz (NTSC)
15.625 KHz (PAL)
Vertical sync
a. Type TTL TTL
b. Polarity Positive or negative Positive or negative
c. Input impedance 1K ohm(Min) 1K ohm(Min)
d. Frequency RGB: 50 Hz ~ 120 Hz
AV/Y CB CR:
60 Hz (NTSC)
50 Hz (PAL)
RGB: 50 Hz ~ 120 Hz
AV/Y CB CR:
60 Hz (NTSC)
50 Hz (PAL)
4. Connector type 15 pin D-type and RCA JACK and
S-terminal 9pin D-SUB 15 pin D-type and RCA JACK and S-terminal 9pin D-SUB
5. Horizontal size 620 +/-8 mm
(for RGB mode 1-9) 520 +/-6 mm (for RGB mode 1-9)
Vertical size 465 +/-8 mm
(for RGB mode 1-9) 388 +/-6 mm (for RGB mode 1-9)

SPECIFICATIONS:
-11 -
MULTIMEDIA MONITOR 34” (4:3) 29” (4:3)
6. Unit dimension:
W X H XD (mm) 866 X718 X583 760 X580 X 513
Packaging dimension :
WX H XD (mm) 1030 X870 X760 890 X705 X700
7. Net weight of unit : 71 Kg 54 Kg
8. User Controls: Power, Brightness, Contrast, V-Size, V-Center, H-Width, H-Phase,
Degauss, Pincushion, Trapezoid, Parallelogram, Rotation, R-Gain,
G-Gain, B-Gain, Bass, Treble, Balance, Color, Tint, Sharpness, Mute,
Volume, Woofer, Recall, Input Select,WIDE.
9. Operating temperature:
0℃to 40℃
10. Pin assignments for D-type connector
Pin 1 : RED Pin 6 : RED RETURN Pin 11 : GND
Pin 2 : GREEN Pin 7 : GREEN RETURN Pin 12 : SDA
Pin 3 : BLUE Pin 8 : BLUE RETURN Pin 13 : H-SYNC
Pin 4 : GND Pin 9 : NC Pin 14 : V-SYNC
Pin 5 : GND Pin10: GND Pin 15 : SCL
11.
a. The table below is required timings and technical description for the
34” tube (H=620mm, V=465mm standard size),
29” tube (H=520mm, V=388mm standard size).
Mode No. 123456789
Resolution
&
Refresh Rate
640
480
60
640
480
72
720
400
70
640
480
66.6
800
600
60.317
800
600
56.25
640
480
85
800
600
72
1024
768
60 Hz
Pixel timing +/-.5% 39.722
31.746
35.311
33.06
25 27.8
36 50 15.385
n Sec
Horizontal visible 640
640 720 640 800 800 640 800 1024
Dots
Horizontal total 800
832 900 864 1056
1024
832 1040
1344
Dots
Horizontal front porch
16 16 18 64 40 24 56 56 40 Dots
Horizontal sync 96 40 108 64 128 72 56 120 145 Dots
Horizontal back porch
48 136 54 96 88 128 80 64 105 Dots
Hor blanking time 160
192 180 224 256 224 192 240 290 Dots
Vertical visible 480
480 400 480 600 600 480 601 768 Lines
Vertical total 525
520 449 525 628 625 509 667 806 Lines
Vertical front porch 10 112 311111Lines
Vertical sync 232342366Lines
Vertical back porch 33 36 35 39 23 22 22 23 29 Lines
Vertical blanking time
45 40 49 45 28 25 26 30 36 Lines
Horizontal frequency
31.469
37.861
31.467
35 37.879
35.156
43.27
48.09
48.363
KHz
Vertical frequency 59.940
72.809
70.082
66.667
60.317
56.250
85 72 60 Hz
Vertical sync polarity
--+-++-+-TTL
Hor sync polarity ---+++-+-TTL
Dot rate 25.2
31.2
28.3
30.204
40 35.97
36 50 65 MHz
The SYNC-ON-GREEN recall is just proper MODE 4.

CONNECTING YOUR MONITOR
-12 -
1. AC IN: This terminal is for AC power cord.
2. RGB 1 IN: This terminal is for RGB analog signal, use with IBM PC and other compatibles.
3. RGB OUT: This terminal can output RGB analog signal that your monitor is using.
(＊This terminal is for rear RGB in Signals )
4. RGB AUDIO IN: These terminals are for sound signal when monitor is in RGB mode.
5. AV1 IN: These terminals are for video and stereo sound signals, used with video equipment.
6. AV2 IN: These terminals are for video and stereo sound signals, used with video equipment.
7. AV3 IN: These terminals are for video and stereo sound signals, used with video equipment.
8. AV OUT: These terminals can output video and variable audio signals that your monitor is using.
9. Y CB CR: This terminal is for Y CB CR signal and stereo sound signals, used with Y CB CR equipment.
10. RS232 IN: This terminal is for control system signal, for use with IBM PCs and compatibles.(page 20)
NOTE :
1. Please follow the above description when connecting your display.
2.This terminal (AV OUT) only supply the AV1 or AV2 type signal and does not supply the Y
CBCRtype signal.
AC IN
RGB 1 IN
¬
-
R
L
RGB OUT
®
AUDIO
¯
µ
°
Y CB CR R
L
´
²
³
COMPONENT
AV
R
L
AV3 ±
AV2 R-AUDIO-L
AV1 R-AUDIO-L
OUT R-AUDIO-L
AUDI
O
RS-232

LOCATION OF BUTTONS ON REMOTE CONTROL
-13 -
Applicable Key Functions
For monitor use POWER、MUTE、DEGAUSS、MENU+、MENU-、INPUT SELECT
ADJ+、ADJ-、VOLUME+、VOLUME-、WOOFER、RECALL、WIDE
For tuner card use
(OPTIONAL)
MTS,CHANNEL+,CHANNEL-,CH ADD/ERASE,FULL SEARCH,CCD,BLUE
BACK ON/OFF,AIR/CABLE,DISPLAY,0~9, 100,QV,SET, t, s, V-CHIP
NOTE: This remote control can be used for monitor and tuner card (OPTIONAL).
CHANNEL+/
-
button (page 20)
20
20
15
INPUT DIRECTLY button
(page 20)
POWER button (page
13)
MUTE
button (page 13)
VOLUME+/
-
button (page
13)
INPUT SELECT button (page 20)
WIDEbutton(page20)
DEGAUSS button (page 14)
??MENUbutton(page14)
??ADJUS button (page
15)
RECALL button (page
13)
WOOFER button (page 13)
INPUT DIRECTLY button
(page 20)

LOCATION OF CONTROL (ON FRONT PANEL)
-14 -
Front view
29”
34"
NOTE:
1. RGB2 IN: This terminal is for RGB analog signal, use with IBM PC and other compatibles
(except MAC PC).
(page 20) (page 20) (page 14) (page 13/15) (page 13)
INPUT
SELECT
DEGAUSS
－
MENU
＋
－
VOL
＋
POWER/ POWER
STANDBY SAVING
POWER
3
ADJUST
4
RGB
-
2IN
▼
CHANNEL
▲
ADJUST
DEGAUSS
－VOL ＋
－MENU ＋
INPUT
SELECT
STAND
BY¯
POWER
SAVING
¯
POWER
¯
RGB-2 IN

INSTALLATION
-15 -
1. Before you connect any cables, refer to the safety instructions at the beginning of this manual and make sure your
computer (or video equipment) and display are switched off.
2. Connect the video cable (AV, S-Video or RGB cable) and audio cable to your monitor.
3. Connect the AC power cord to your monitor.
4. Plug the AC power cord to a properly grounded outlet.
5. Turn on your computer or video equipment.
6. Turn on your monitor‘s power by pushing the power button. The power indicator should be illuminated.
NOTE: If the button does not function due to interference, disconnect from the main
power supply for 10 seconds. Then reconnect and turn the power on.
AC IN
RGB 1 IN
LASERDISKorVCD
or VCR
GAME PLAYER
DVD PLAYER / SET TOP BOX PC/NOTEBOOK
R
L
AUDIO
RGB OUT
MONITOR
°
Y CB CR R
L
´
²
³
COMPONENT
AV
R
L
AV3 ±
AV2 R-AUDIO-L
AV1 R-AUDIO-L
OUT R-AUDIO-L
AUDI
O
RS-232
INPUT
SELECT
DEGAUSS
－
MENU
＋
－
VOL
＋
STANDBY POWER
POWERSAVING
POWER
3
ADJUST
4
RGB
-
2IN
▼
CHANNEL
▲

USING THE MONITOR’S ADVANCED FEATURES
-16 -
The ” Digital Vision” feature advanced on screen adjustment for optimal viewing. To access the
advanced features, open the access panel by pressing the center of the door on the set or use the
remote control.
Press the power button, when the green LED (power) lights up, the
power is ON. Press the button again, the green LED
disappears and the red LED (stand by) lights up indicating that the
power is OFF.
The following audio functions are available only if speakers are
attached.
Press and hold the Volume + button to increase the volume lev
el.
Press and hold volume -button to decrease the volume level.
The Volume +/-button on front panel becomes ADJ +/-
button, after
the menu window appears on screen.
Use this button to quickly turn off the sound being heard through the
speakers.
To enable the mute functions simply press the button.
(Once pushed, the on screen display will appear next to the button
indicating that the mute function is enabled). To disable the mute
function, simply press the button again, the On Screen Display will
disappear and sound will be restored from the speakers.
Press this button to return the display to the factory pre-set
default value. No recall item:
RGB : Rotation
Y PB PR: Rotation
Press this button to switch the woofer ON or OFF.
Each time the button is pressed, the on screen display will appear
“woofer on”, “woofer off” in turn.
POWER
-VOLUME +
MUTE
R/C ONLY
RECALL
R/C ONLY
WOOFER
R/C ONLY

USING THE MONITOR’S ADVANCED FEATURES
-17 -
Each time you turn on your monitor it is automatically degaussed.
Degaussing keeps the display free from unwanted magnetism that
can result in co
lor impurity. If you leave your display on
continuously, we recommend that you degauss it at least every few
days to remove any color impurities.
Press the degauss button, then degaussing is accompanied by brief
instability of the displayed image and a bri
ef humming sound. A
minimum of 20 minutes should be observed between
each use of the manual degauss button.
To view the monitor current settings press menu +/-button
and an On Screen Display window appears. The last line of the
window reports t
he current resolution and frequency settings. The
first line of the window displays the master picture menu and the
setting of a selected feature.
The On Screen Display menus of RGB mode and TV/AV mode,YCB CR mode appear below.
RGB menu On Screen Display
TV/AV menu On Screen Display
M:01 FH:31KHz FV: 60Hz
128
BRIGHT
M:TV/AV FH:15KHz FV:60Hz
128
R←→B
BRIGHT
DEGAUSS
MENU -MENU +

USING THE MONITOR’S ADVANCED FEATURES
-18 -
Y CB CR menu on screen display:
To change monitor setting of the Master Picture Menu, you must
choose a category, and then adjust the value of each category.
Here’s how to select a category:
Press the menu + or menu –button while the master picture menu
is on screen.
Each time the menu + button is pressed, a menu icon shows red for
selection. Beginning with the starting position, and moving to the
right, pressing the menu + button continuously will circulate the
selector, eventually returning to the starting position.
Press the menu –button and it will select menu icon in the
opposite direction, eventually returning to the starting position.
After you have selected a category, you can i
ncrease or decrease
a display setting. Here’s how to adjust a setting:
Press the menu +/-
button. While the master picture menu is on
screen, use the menu + or menu–
select key to choose a category.
Once you have selected a category, press the ADJ + or ADJ –
button. Each time the ADJ + adjust button is pressed, the settings
for the category selected will increase. Each time the ADJ –
button
is pressed, the settings for the category selected will decrease.
You can adjust monitor settings for the following categories:
RGB menu On Screen Display
M: YCBCR FH :15KHz FV :60Hz
128
R←→B
BRIGHT
M : 01 FH:31KHz FV: 60Hz
128
BRIGHT
3ADJ 4
-VOL +

USING THE MONITOR’S ADVANCED FEATURES
-19 -
BRIGHT.Select this icon to adjust the overall picture brightness
(image black level). Set the brightness so that the dark areas of the
monitor remain black. Press the ADJ -button to decrease
brightness. Press the ADJ + button to increase brightness.
CONTRAST. Select this icon to adjust the contrast (image white
level). Contrast is the difference in brightness between the
Dark and light parts of the displayed image. Press the ADJ-
Button to decrease contrast. Press the ADJ + button to increase
contrast.
V-SIZE. Select this icon to adjust the vertical size of the
displayed image. Press the ADJ -button to decrease V-Size. Press
the ADJ + button to increase V-Size.
V-CENTER. Select this icon to adjust the vertical position of the
displayed image with respect to the frame of the screen. Press the
ADJ-button to decrease V-Position. Press the ADJ+ button to
increase V-Position.
H-WIDTH. Select this icon to adjust the horizontal size of t
he
displayed image. Press the ADJ-button to decrease H-
Width.
Press the ADJ + button to increase H-Width.
H-PHASE
. Select this icon to adjust the horizontal position of the
displayed image with respect to the frame of the screen. Press the
ADJ-button to decrease H-
Phase. Press the ADJ + button to
increase H-Phase.
PINCUSHION. Select this icon to adjust the amount of tapering
on each side of the displayed image. Press the ADJ-
button to
decrease the amount of side pincushion. Press the ADJ + button
to
increase the amount of side pincushion.
TRAPEZOID. Select this icon to adjust the trapezoid.
Press ADJ -
button to let the upper screen move to center and
lower screen move to outside. Press ADJ + button to let the upper
screen move to outside and lower screen move to center.
PARALLELOGRAM
. Select this icon to adjust the

USING THE MONITOR’S ADVANCED FEATURES
-20 -
parallelogram. Press ADJ + button to let the screen slant to left
side and press ADJ -button to let the screen slant to right side.
ROTATION. Select this icon to adjust th
e screen tilt of the
displayed image. This is used to compensate for earth magnetic
field effect on the monitor.
R-GAIN.Select this icon to change the gain of red.
G-GAIN.Select this icon to change the gain of green.
B-GAIN.Select this icon to change the gain of blue.
BASS.Select this icon to adjust bass of sound.
TREBLE.Select this icon to adjust treble of sound.
BALANCE.Select this icon to adjust balance of sound.
TV/AV menu on screen display
BRIGHT.Select icon to adjust the overall picture brightness
(image black level). Set the brightness so that the dark areas of the
monitor remain black. Press the ADJ -button to decrease
brightness. Press the ADJ + button to increase brightness.
CONTRAST.Select this icon to adjust the contrast (image white
level). Contrast is the difference in brightness between the dark
and light parts of the displayed image. Press the ADJ -button to
decrease contrast. Press the ADJ + button to increase contrast.
R←→B
M : TV/AV FH : 15KHz FV : 60Hz
128
BRIGHT