Samsung SADT-104WM User manual

SADT - 104WM
Wall Mount Adaptor
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/global/register
SADT-104WM_ENG.indd 1 2008-01-24 오전 10:24:02

ENG
SADT-104WM_1
Overview
The WALL MOUNT ADAPTOR is used to install the SMARTDOME
CAMERA (SCC-C6433/C6435) in an indoor wall.
Notice
• Make sure that you must select an installation spot to endure the total weight of "Wall
Mount Adapter", "Smart Dome Camera".
• This product is designed to use with anchor bolts and anchor nuts (M10).
• If installing in a concrete wall, use a M10 anchor bolt (nut) with flat washer and spring
washer.
• Each installed anchor bolt should endure 700kg of pulling force.
• Wall Mount Adapter can be installed directly in the wall, and also attached to CORNER
MOUNT ADAPTOR(SADT-110CM), or POLE MOUNT ADAPTOR(SADT-100PM)
Installation
1. Select an installation spot which can endure more than 4 times of the product weight.
2. Refer to the user guide of the SMARTDOME CAMERA, prepare the outdoor power cable,
BNC cable, communication cable to connect the Camera.
SADT-104WM_ENG.indd 1 2008-01-24 오전 10:24:03

2_SADT-104WM
3. If you install the Wall Mount Adaptor in a wall, place the template on the wall and drill 4
holes for the anchor bolts (M10) and nuts (M10) before inserting them.
If you install it in a corner of the wall, use the Corner Mount Adaptor (SADT-110CM). If
installing on the pole of the wall, use the Pole Mount Adaptor (SADT-100PM).
4. Prepare the Camera Adaptor for the applicable camera.
Remove the Bracket Sealing from the Camera Adaptor.
TEMPLATE
The positions for
installing a ANCHOR BOLT
80 mm
150 mm
BRACKET CEILING
CAMERA ADAPTOR
SADT-104WM_ENG.indd 2 2008-01-24 오전 10:24:03

ENG
SADT-104WM_3
5. Remove the Connectors at the end of the Camera Adaptor.
In the next step, peel off the coating of the cable and connect it to the external cable
using soldering. (See the wiring diagram of the installation guide for the Camera to
connect the cables.)
Lastly, use an insulation tape to wrap up the soldering portion of two cables.
Repeat the above steps to connect all of the 4 Connectors to the appropriate external
cables.
CAMERA ADAPTOR CAMERA ADAPTOR
CABLE
CONNECTOR
EXTERNAL CABLE
BNC JACK SOLDERING
CONNECTOR
CONNECTOR BNC JACK
EXTERNAL CABLE
SADT-104WM_ENG.indd 3 2008-01-24 오전 10:24:04

4_SADT-104WM
6. Prepare the Camera Adaptor for the applicable camera. Refer to the installation guide for
the applicable camera and configure the initial settings of the Camera Adaptor.
(For more information, see the installation guide for the Camera)
Insert the cable of the Camera Adaptor into the Wall Mount Adaptor before pulling it out
throught the hole of the Cover Fixing Part.
7. Insert the 4 screws on the Wall Mount Adaptor into the corresponding screw holes on the
Camera Adaptor and fix them so that the Camera Adaptor is secured to the Wall Mount
Adaptor.
Ensure that the part “A” of the Camera Adaptor faces the arrow direction in the figure
during the fixation.
WALL MOUNT ADAPTOR
the place for joining a cover
CAMERA ADAPTOR
WALL MOUNT ADAPTOR
SCREW
The place for
joining a screw
CAMERA ADAPTOR
WALL MOUNT ADAPTOR
"A" CAMERA ADAPTOR
SCREW
"A"
SADT-104WM_ENG.indd 4 2008-01-24 오전 10:24:05

ENG
SADT-104WM_5
8. Pull out cables such as external power cable, BNC cable and communications cable
through the rear of the Wall Mount Adaptor, which are necessary for connecting the
camera.
It is recommended to keep the cables about 100mm longer than the cover fixing part.
9. Use the anchor bolts and nuts to secure the Wall Mount Adaptor to the wall.
100mm
WALL MOUNT ADAPTOR
the place for joining a cover
WALL MOUNT ADAPTOR
CAMERA ADAPTOR
ANCHOR BOLT
SADT-104WM_ENG.indd 5 2008-01-24 오전 10:24:07

6_SADT-104WM
10. Connect the cables of the Camera Adaptor with the outward cables, which then you
push in through the Cover Fixing Part to the Wall Mount Adaptor.

Insert one piece of the two-strand cable into an empty area of the Wall Mount
Adaptor as in the figure below and push the other one into the Wall Mount Adaptor.
CAUTION
When you insert the cables into the Cover Fixing Part so that the insulation of the
cable junction is not peeled off or torn.
11. As in the bottom-left figure, insert the rib of the cover into the Cover Fixing Part. Then,
push the Sanp-Fit of the cover into the Cover Fixing Part so that the cover is fastened
with the Wall Mount Adaptor.
WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR
< Insert one piece of the two-stranded cable > < Insert the other piece of the two-stranded cable >
the place for joining a cover
WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR
the place for joining a cover
CAMERA ADAPTOR CAMERA ADAPTOR
COVER
COVER
COVER
RIB
SNAP-FIT
SADT-104WM_ENG.indd 6 2008-01-24 오전 10:24:08

ENG
SADT-104WM_7
12. Prepare the Camera Body.
Put up the Safety Wire, attached to the camera, on the Safety Hook.
CAUTION
To avoid accidental fall and consequent damage to the camera during installation or
detachment, make sure the Safety Wire is secured to the hook.
CAMERA ADAPTOR
CAMERA ADAPTOR
WALL MOUNT ADAPTOR
WALL MOUNT ADAPTOR
SAFETY HANGER
SAFETY HANGER
SAFETY WIRE SAFETY WIRE
CAMERA
CAMERA
SADT-104WM_ENG.indd 7 2008-01-24 오전 10:24:10

8_SADT-104WM
13. Align the Guide 1 of the Camera with the Guide 2 of the Camera Adaptor and insert the
3 Guides of the Camera into the corresponding Guide Holes of the Camera Adaptor.
Then, turn the camera clockwise by 10 degrees.
Make sure that the part "A" is moved from position 1 to 2.
WALL MOUNT ADAPTOR
CAMERA ADAPTOR CAMERA ADAPTOR
GUIDE HOLE
GUIDE
CAMERA
GUIDE 2 GUIDE 3
Align!
GUIDE 1
SCREW
CAMERA
CAMERA ADAPTOR
GUIDE HOLE
GUIDE
CAMERA
WALL MOUNT ADAPTOR
CAMERA
"A"
1 2
SADT-104WM_ENG.indd 8 2008-01-24 오전 10:24:11

ENG
SADT-104WM_9
14. Use the screws, attached to the Camera, to firmly fix the Camera body with the
Camera Adaptor.
(Once you removed the camera from the Camera Adaptor, loosen the screw, turn the
camera counterclockwise by about 10 degrees, and then pull it down.)
CAUTION
If you do not fix the screws, CAMERA BODY could be separated from the CAMERA
ADAPTER due to the shake.
To avoid safety accident and camera damage, make sure to fix the screws.
WALL MOUNT ADAPTOR
CAMERA
SCREW
SADT-104WM_ENG.indd 9 2008-01-24 오전 10:24:12

10_SADT-104WM
Product Specification
Location for use: Indoors
Installation Spot: Wall or Vertical Structure
Dimension: See the figure
Weight: 241g
Material: plastic
Operation Temperature: -10˚C ~ 50˚C
Accessories
Template .................................. 1
Cover ....................................... 1
MANUAL .................................. 1






 
Ø117
4- Ø10,5
SADT-104WM_ENG.indd 10 2008-01-24 오전 10:24:12

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government ofce, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
SADT-104WM_ENG.indd 11 2008-01-24 오전 10:40:05