Samsung SyncMaster 170T User manual

COLOR MONITOR
SyncMaster 170T
SyncMaster 180T
Manual
SERVICE
COLOR MONITOR CONTENTS
1. Precautions
2. Product Specifications
3. Disassembly & Reassembly
4. Alignments & Adjustments
5. Troubleshooting
6. Exploded View & Parts List
7. Electrical Parts List
8. Block Diagram
9. Wiring Diagram
10. Schematic Diagrams
SyncMaster 170T
SyncMaster 180T

Samsung Electronics Co., Ltd. June 2000
Printed in Korea
Code No.: BN68-00049V-01

1-1-1 Warnings
1. For continued safety, do not attempt to modify the
circuit board.
2. Disconnect the AC power and DC power jack
before servicing.
1-1-2 Servicing the LCD Monitor
1. When servicing the LCD Monitor, Disconnect the
AC line cord from the AC outlet.
2. It is essential that service technicians have an
accurate voltage meter available at all times. Check
the calibration of this meter periodically.
1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the
following safety checks:
1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.
2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
3. Leakage Current Hot Check (Figure 1-1): WARNING:
Do not use an isolation transformer during this test.
Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for
Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).
Figure 1-1. Leakage Current Test Circuit
4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat
the test.
1-1-4 Product Safety Notices
Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by
on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.
SyncMaster 170T/180T 1-1
1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1 Safety Precautions
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
(READING SHOULD
NOT BE ABOVE 0.5mA)
LEAKAGE
CURRENT
TESTER
2-WIRE CORD
*ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED) EARTH
GROUND
!

1-2-1 General Servicing Precautions
1. Always unplug the unit’s AC power cord from the
AC power source and disconnect the DC Power
Jack before attempting to:
(a) remove or reinstall any component or assembly,
(b) disconnect PCB plugs or connectors, (c) connect
a test component in parallel with an electrolytic
capacitor.
2. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
3. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.
1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist-
strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.
2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.
3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.
4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.
5. Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.
4. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).
5. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.
The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.
6. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting the
positive lead; always remove the instrument’s
ground lead last.
6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.
7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
Caution: Be sure no power is applied to the
chassis or circuit and observe all
other safety precautions.
8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.
1 Precautions
1-2 SyncMaster 170T/180T
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-
effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1-2 Servicing Precautions
WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions
section of this manual.
Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the
safety precautions, always follow the safety precautions.

2 Product Specifications
2-1 Specifications
LCD Panel TFT-LCD panel, RGB vertical stripe, normally black transmissive,
17-Inch (18.1-Inch) viewable, 0.264 (H) x 0.264 (V) mm pixel pitch
Scanning Frequency Horizontal : 30 kHz to 81 kHz (Automatic) 30 kHz to 64 kHz
Vertical : 56 Hz to 85 Hz (~XGA), 76 Hz (SXGA) 56 Hz to 85 Hz (~XGA),60Hz(SXGA)
Display Colors 16,7 Million colors
Maximum Resolution Horizontal : 1280 Pixels @ 81 kHz 64kHz
Vertical : 1024 Pixels @ 76 Hz 60Hz
Input Video Signal Analog, 0.714 Vp-p ± 5% positive at 75 Ω, TMDS
internally terminated
Input Sync Signal Type : Seperate H/V sync, Composite H/V, Sync-on-Green
Level : TTL level (V high ≥2.0 V, V low ≤0.8 V), Sync-on-Green (≤–0.25 V)
Maximum Pixel Clock rate 135 MHz 108MHz
Active Display 338 ± 3 mm
Horizontal/Vertical 270 ± 3 mm
AC power voltage & Frequency AC 90 to 264 Volts, 60/50 Hz ± 3 Hz
Power Consumption 42 W (max.), 40W (normal)
Dimensions
Unit (W x D x H) 17.32 x 7.16 x 18.19 Inches (440 x 182 x 462 mm) 17.7 x 18.2 x 7.2 Inches (449.4 x 461.2 x 182 mm)
Carton (W x D x H) 22.91 x 22.51 x 12.48 Inches (582 x 572 x 317 mm) 22.4 x 11.6 x 22.8 Inches (570 x 295 x 580 mm)
Weight
(Net/Gross) 7.9 kg (17.41 lbs) / 10.3 kg ( 22.70 lbs) 8.3 kg (18.29 lbs) / 11.8 kg ( 26.01 lbs)
Environmental Considerations Operating Temperature : 50°F to 104°F (10°C to 35°C)
Humidity : 10 % to 80 %
Storage Temperature : -68°F to 113°F (-20°C to 45°C)
Humidity : 5 % to 95 %
• SyncMaster 170T/180T comply with SWEDAC (MPRII) recommendations for reduced electromagnetic fields.
• Designs and specifications are subject to change without prior notice.
SyncMaster 170T/180T 2-1
Item
Analog Digital
Description
170T 180T

No Connection
DDC Power Input (+5V)
Self Raster
Connection Signal Output (+5V)
Rx0-
Rx0+
GND
No Connection
No Connection
GND
RxC+
RxC-
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
Rx2-
Rx2+
GND
No Connection
No Connection
DDC Clock (SCL)
DDC Data (SDA)
No Connection
Rx1-
Rx1+
GND
No Connection
2 Product Specifications
2-2 SyncMaster 170T/180T
2-2 Pin Assignments
Sync
Type
Pin No.
15-Pin D-Sub Signal Cable Connector
Separate Composite
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red
Green
Blue
GND
DDC Return (GND)
GND-R
GND-G
GND-B
DDC Power Input (+5V)
Self Raster
GND
Bi-Dr Data (SDA)
H-Sync
V-Sync
DDC Clock (SCL)
Red
Green
Blue
GND
DDC Return (GND)
GND-R
GND-G
GND-B
DDC Power Input (+5V)
Self Raster
GND
Bi-Dr Data (SDA)
H/V-Sync
Not Used
DDC Clock (SCL)
Red
Green + H/V Sync
Blue
GND
DDC Return (GND)
GND-R
GND-G
GND-B
DDC Power Input (+5V)
Self Raster
GND
Bi-Dr Data (SDA)
Not Used
Not Used
DDC Clock (SCL)
Sync-on-green
Sync
Type
Pin No.
24-Pin DVI-D(TMDS)

2 Product Specifications
SyncMaster 170T/180T 2-3
QRS
P
O
Video
Sync Sync
Horizontal Vertical
CDE
P
O
B
A
Video
Sync Sync
Separate Sync
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.
C D
AO
E
BP
Video
Sync Sync
Video
Q R S
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch
VIDEO
A
BO
P
QRS
Horizontal Vertical
B
Green
Vertical
PQRS
O
Horizontal
H/V Composite Sync
Sync-on-Green
79.976
12.504
1.067
1.837
9.481
0.119
75.025
13.329
0.038
0.475
12.804
0.013
135.000
Positive
Positive
Separate
81.129
16.640
6.400
2.880
3.200
76.106
10.660
0.080
3.200
0.020
135.000
Negative
Negative
Com.
68.677
14.561
1.016
2.201
10.836
0.508
84.997
11.765
0.044
0.524
11.183
0.015
94.500
Positive
Positive
Separate
1024/85Hz
1024x768
1280/76Hz
1280x1024
1280/75Hz
1280x1024
1024/75Hz
1024 x 768
60.023
16.660
1.219
2.235
13.003
0.203
75.029
13.328
0.050
0.466
12.795
0.017
78.750
Positive
Positive
Separate
31.469
31.777
3.813
1.589
26.058
0.318
70.087
14.268
0.064
0.858
13.155
0.191
28.322
Negative
Positive
Separate
fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock
Freq.
(MHz)
Polarity
H.Sync
V.Sync
Remark
IBM
640/75 Hz
640 x 480
640/85 Hz
640 x 480
800/75 Hz
800 x 600
800/85 Hz
800 x 600
1024/60Hz
1024 x 768
VGA2/
70 Hz
720 x 400
VGA3/
60 Hz
640 x 480
Table 2-1. Timing Chart
31.469
31.778
3.813
1.589
26.058
0.318
59.940
16.683
0.064
0.794
15.761
0.064
25.175
Negative
Negative
Separate
37.500
26.667
2.032
3.810
20.317
0.508
75.000
13.333
0.080
0.427
12.800
0.027
31.500
Negative
Negative
Separate
43.269
23.111
1.556
2.222
17.778
1.556
85.008
11.764
0.671
0.578
11.093
0.023
49.500
Negative
Negative
Separate
46.875
21.333
1.616
3.232
16.162
0.323
75.000
13.333
0.064
0.448
12.800
0.021
49.500
Positive
Positive
Separate
53.674
18.631
1.138
2.702
14.222
0.569
85.061
11.756
0.056
0.503
11.179
0.019
56.250
Positive
Positive
Separate
48.363
20.677
2.092
2.462
15.754
0.369
60.004
16.666
0.124
0.600
15.880
0.062
75.000
Negative
Negative
Separate
Mode VESA
Timing (Analog Only) (Analog Only)

2 Product Specifications
2-4 SyncMaster 170T/180T
Memo

3-1-1 Removing the Stand
1. With a pad beneath it, stand the monitor on its
front with the screen facing downward and
the base close to you. Make sure nothing will
damage the screen.
2. Remove the 4 screws on the Stand.
Caution: Be careful. The signal cable and
power cable are still attached to the
monitor.
3. Disconnect the Signal Cable and Power Cord.
3-1-2 Main Body Disassembly
1. Remove 2 screws on the Rear Cover.
2. Pull the Rear Cover up and off the monitor.
3. Remove 15 screws on the PCB Shield and
remove the Shield.
4. Remove 4 screws on the Main PCB and 2
screws on the Inverter PCB and 2 screws on
the 10P Harness.
5. Disconnect the interface wire (31P) between
the Panel and the CN601 connector on the
Main PCB.
6. Disconnect the Function PCB wire (10P)
between the Function PCB and the CN102
connector on the Main PCB.
7. Disconnect 2 Inverter wires between the Panel
and the CN2, 3 connectors on the Inverter PCB
and disconnect the 12P harness between CN1
connector on the inverter and CN103
connector on the Main PCB.
8. Carefully lift the Main PCB Assembly and
Inverter PCB and place them on a flat, level
surface that is protected from static electricity.
9. Remove 4 screws on the PCB Bracket.
10. Remove the Bracket Assembly from the Front
Cover.
11. Remove the 3 screws on the Function PCB
from the Front Cover and remove the
Function PCB and Function Knob.
12. Remove 4 screws on the Front Shield and
remove the PCB Bracket and the Front Shield.
SyncMaster 170T/180T 3-1
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the
SyncMaster 170T/180T TFT-LCD monitors.
WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling
these components.
3-1 Disassembly (SyncMaster 170T)
Cautions:1. Disconnect the monitor from the power source before disassembly.
2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

3 Disassembly and Reassembly
3-2 SyncMaster 170T/180T
3-2-1 Removing the Stand
1. Remove 4 screws on the Stand.
3-2-2 Main Body Disassembly
1. Remove 4 screws on the Rear Cover.
2. Pull the Rear Cover up and off the monitor.
3. Remove 4 screws on the BRKT-VESA and
Remove the BRKT-VESA.
4. Remove 16 screws on the PCB Shield and
remove the Shield.
5. Remove 7 screws on the Main PCB and 2
screws on the Inverter PCB and 2 screws on
the 10P Harness.
6. Disconnect the connector (140P) between the
Panel and the CN600 connector on the Main
PCB.
7. Disconnect the Function PCB wire (10P)
between the Function PCB and the CN102
connector on the Main PCB.
8. Disconnect 2 Inverter wires between the Panel
and the CN2, CN3 connectors on the Inverter
PCB.
9. Disconnect the 12P harness between CN1
connectors on the Inverter PCB and CN103
connector on the Main PCB.
10. Carefully lift the Main PCB Assembly and
Inverter PCB and place them on a flat, level
surface that is protected from static electricity.
11. Remove 10 screws on the PCB Bracket.
12. Remove the Bracket Assembly from the Front
Cover.
13. Remove the 2 screws on the Function PCB
from the Front Cover and remove the
Function PCB and Function Knob.
3-2 Disassembly (SyncMaster 180T)
3-3 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures.

SyncMaster 170T/180T 5-1
5 Troubleshooting
Notes: 1. Before troubleshooting, setup the PC’s display as below.
• Resolution: 1280 x 1024
• H-frequency: 64 kHz
• V-frequency: 60 Hz
2. If no picture appears, make sure the power cord is correctly connected.
3. Check the following circuits.
• No raster appears: Stand PCB, Main PCB
• 14V develop but no screen: Main PCB
• 14V does not develop: Main PCB
4. If you push and hold the EXIT button for more than 5 seconds, the monitor automatically turns back
to the factory preset.
5-1 No Power
Does proper DC 14 V appear at
DC jack connected to CN101? Check Power Adaptor.
Yes
No
Does proper DC 5 V appear at
Pin 4 of IC105? Check IC105 and related circuit.
Check Q102, Q103 and Q105.
Yes
No
Does proper 5 V - signal appear at
Pin 42 of IC602 (SW_REG_EN)?
Check IC602 and related circuit.
(CN102, Function Key)
Yes
No

5 Troubleshooting
5-2 SyncMaster 170T/180T
5-2 No Video [Analog]
Check signal cable and connection.
Check PC Signal
No
No
No
Does the analog video signal appear at
R200,R201, R202? (BLUE, GREEN, RED)
Yes
Check IC244 and related circuit.
Does the sync signal appear
at the output of Pin 18, 14 of IC 244 ?
(V_SYNC, H*V_SYNC)
Yes
No
Check the related circuit
for these ports
No
Check IC501 and related circuit.
No
Check IC501 and related circuit.
No
Check IC300 and related circuit.
No
Does the input signal appear at the Pin 40, 41 of
IC 300?
(PLL H*V, MX-PDEN)
Yes
During power on-off, does the input signal
appear at the Pin29,30 of IC300?
(AD-SDA, AD-SCL)
Do the clock and sync signal appear at Pin115,
117 of IC 300? (A_DCLKAB,
A_MX_HSYNC) and does the digital video signal
appear at the output port PDA, PDB)?
Yes
During power on-off dose the input signal
appear at the R 410 and R 411 ?
(MX-SDA, MX-SCL)
Yes
7 8
9 10
1 2 3 4
5 6
Does the digital video signal appear
at the Pin 34, 35, 39, 40, 42, 43, 45 and 46 of IC601?
Yes
Is the output of Pin 1, 19 of IC602 High? Check TFT-LCD panel and Inverter.
Yes
replace IC601
Yes
15 16 17 18
Check IC602 and related circuit.
No
Does the input signal appear at Pin of 76, 77, 78,
80 of IC601 (LDTGB, LVSYNCB, LHSYNCB, LCKBB)

5 Troubleshooting
SyncMaster 170T/180T 5-3
5-2-1 No Video [Digital]
Check signal cable and connection.
Check PC Signal and IC101
Does the input signal appear at Pin of 76, 77, 78,
80 of IC601 (LHSYNCB, LVSYNCB,LDTGB, LCKBB)
No
No
No
Does the digital signals appear at R328, R329,
R330,R332, R333, R334, R335 and R336 (IC101)?
Yes
Check IC244 and related circuit.
Does the sync signal appear
at the output of Pin 18, 14 of IC 244 ?
(V_SYNC, H*V_SYNC)
Yes
No
Check the related circuit
for these ports
No
Check IC501 and related circuit.
No
Check IC101 and related circuit.
No
Does the input signal appear at the Pins 40, 41
of IC 300?
( PLL H*V, MX_PDEN)
Do the clock and DE signal appear at Pin 44, 46 of
IC 101? (T_,DCLK, T_DE) and does the
digital video signal appear at the output port PDA,
PDB)?
Yes
During power on-off dose the input signal
appear at the R 410 and R 411 ?
(MX-SDA, MX-SCL)
Yes
7 8
19 20
1 2 3 4
5 6
Does the digital video signal appear
at the Pin 34, 35, 39, 40, 42, 43, 45 and 46 of IC601?
Yes
Is the output of Pin 1, 19 of IC602 High? Check TFT-LCD panel and Inverter.
Yes
Replace IC601
Yes
15 16 17 18
Check IC602 and related circuit.
No
18
151617

5-4
5 Troubleshooting
SyncMaster 170T/180T
WAVEFORMS
2
CH1 RMS = 3.25V
3
CH1 RMS = 3.12V
4
CH1 RMS = 2.20V
5
CH1 RMS = 3.3V
6
CH1 RMS = 3.3V
17
CH1 RMS = 3.08V
18
CH1 RMS = 3.08V
9
CH1 RMS = 2.50V
10
CH1 RMS = 960mV
15
CH1 RMS = 3.3V
16
CH1 RMS = 3.3V
8
CH1 RMS = 3.24V
1
CH1 RMS = 3.26V
7
CH1 RMS = 3.20V
19
CH1 RMS = 2.78V
20
CH1 RMS = 3.22V

5-5
5 Troubleshooting
SyncMaster 170T/180T
Replace IC404.
Yes
No
There is video but no OSD.
5-3 No OSD
While pushing a front control
button does any pulse appear
at Pin 12 of IC404?
WAVEFORMS
Does input signal appear
at the Pins 2, 5 and
10 of IC404?
Check IC405 and related circuit.
Check IC404 and related circuit.
Yes
No
11 12 13
11
CH1 RMS = 4.18V
13
CH1 RMS = 3.26V
12
CH1 RMS = 3.26V

SyncMaster 170T/180T 6-1
6 Exploded View and Parts List
6-1 SyncMaster 170T

6 Exploded View & Parts List
6-2 SyncMaster 170T/180T
6-2 SyncMaster 180T

6 Exploded View & Parts List
SyncMaster 170T/180T 6-3

6 Exploded View & Parts List 6-4 SyncMaster 170T/180T

BD101 2901-001114 FILTER-EMI SMD “25VDC,2.0ADC,-,100nF,3.2x1.6x1”
BD102 2901-001114 FILTER-EMI SMD “25VDC,2.0ADC,-,100nF,3.2x1.6x1”
BD103 2901-001114 FILTER-EMI SMD “25VDC,2.0ADC,-,100nF,3.2x1.6x1”
BD104 2901-001114 FILTER-EMI SMD “25VDC,2.0ADC,-,100nF,3.2x1.6x1”
BD105 2703-001334 INDUCTOR-SMD “1.5uH,10%,2x1.25x0.85mm”
BD204 2901-001114 FILTER-EMI SMD “25VDC,2.0ADC,-,100nF,3.2x1.6x1”
C100 2402-001042 “C-AL,SMD” “100uF,20%,16V,GP,TP,6.6x6.6x5.”
C101 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C102 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C103 2402-001044 “C-AL,SMD” “100uF,20%,25V,-,TP,8.3x8.3x6.3”
C104 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C105 2203-000257 “C-CERAMIC,CHIP” “10nF,10%,50V,X7R,TP,1608,-”
C106 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C107 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C108 2402-001042 “C-AL,SMD” “100uF,20%,16V,GP,TP,6.6x6.6x5.”
C113 2409-001004 C-ORGANIC “100uF,20%,16V,LL,BK,8x10.5,3”
C114 2203-000257 “C-CERAMIC,CHIP” “10nF,10%,50V,X7R,TP,1608,-”
C115 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C116 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C117 2402-001044 “C-AL,SMD” “100uF,20%,25V,-,TP,8.3x8.3x6.3”
C118 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C119 2203-000257 “C-CERAMIC,CHIP” “10nF,10%,50V,X7R,TP,1608,-”
C120 2402-001042 “C-AL,SMD” “100uF,20%,16V,GP,TP,6.6x6.6x5.”
C121 2409-001029 C-ORGANIC “120uF,20%,6.3V,WT,TP,10.3x10.3”
C122 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C123 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C124 2402-001042 “C-AL,SMD” “100uF,20%,16V,GP,TP,6.6x6.6x5.”
C125 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C126 2402-001044 “C-AL,SMD” “100uF,20%,25V,-,TP,8.3x8.3x6.3”
C127 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C128 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C129 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C130 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C131 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C132 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C133 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C134 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C150 2402-000176 “C-AL,SMD” “10uF,20%,16V,GP,TP,4.3x4.3x5.4”
C152 2402-000176 “C-AL,SMD” “10uF,20%,16V,GP,TP,4.3x4.3x5.4”
C201 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C202 2402-000176 “C-AL,SMD” “10uF,20%,16V,GP,TP,4.3x4.3x5.4”
C203 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C204 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C205 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
C206 2203-005005 “C-CERAMIC,CHIP” “100nF,15%,16V,W5R,TP,1608,1.6m”
SyncMaster 170T/180T 7-1
Loc. No. Code No. Description Specification Remarks
7 Electrical Parts List
7-1 Main PCB Parts