Samsung HP-P3761 User manual

Remote Control Buttons
ŒPOWER button
Turns the PDP on and off.
´ASPECT button
Changes the screen size.
ˇNumber buttons
¨+100 button
Press to select channels over 100. For example, to select
channel 121, press “+100”, then press “2” and “1.”
ˆMUTE button
Mutes the PDP sound.
ØVOL (Volume) buttons
Adjust volume.
∏SLEEP button
Selects a preset time interval for automatic shutoff.
”MENU button
Displays the main on-screen menu.
’ENTER button
Confirms a selection.
˝PIP button
Activates picture in picture.
ÔSTILL button
Pauses the current screen.
LCD Display
When you press any button, ‘ ‘ appears along with
selected mode (TV, VCR, CATV, DVD, or STB) and
the remote's battery charge status.
ÒP.MODE button
Adjust the PDP picture by selecting one of the preset
factory settings (or select your personal, customized
picture settings).
ÚMODE button
Selects a target device to be controlled by the Samsung
remote control (i.e., VCR, Cable, DVD players, or Samsung
STB). If you change modes, the new mode is momentarily
displayed on LCD.
ÆPRE-CH button
Tunes to the previous channel.
ıSOURCE button
Press to display all of the available video sources
(TV, AV1, AV2, S-VIDEO, COMPONENT1, COMPONENT2,
and DVI).
˜CH (Channel) buttons
Switch channels.
¯INFO button
Press to display information on the PDP screen.
˘EXIT button
Exits the menu.
¿Up/Down Left/Right buttons
Controls the cursor in the menu.
Remote Control

¸SRS TSXT button
Selects TruSurround XT mode.
˛MTS button
Chooses stereo, mono or Separate Audio Program
(SAP broadcast).
◊AUTO PROG. button
The TV automatically cycles through all of the
available channels and stores them in memory.
±ADD/DEL button
Adds or deletes channels in the TV’s memory.
≠DNIe button
Activates DNIe (Digital Natural Image engine).
–CAPTION button
Controls the caption decoder.
—SET button
Used during set up of this Samsung remote control,
so that it will work compatibly with other devices
(VCR, Cable Box and DVD).
÷PIP control buttons
SIZE : Changes the size of the PIP window.
SWAP : Exchanges the video signal that is
currently displayed on the main screen
with the signal in the PIP window.
CH
, :Displays the available channels in
sequence. (These buttons change
channels in the PIP window only).
®VCR, DVD control buttons
Controls VCR tape or DVD disc functions: Stop,
Rewind, Play/Pause, and Fast Forward.
∑RESET button
If your remote control is not functioning properly, take
out the batteries and press the reset button for about
2~3 seconds. Re-insert the batteries and try using the
remote control again.
Installing the Batteries in Your Remote Control
1Slide the back cover
to open the battery
compartment of the
remote control.
3Slide the cover back into
place.
2Install two AAA size batter-
ies. Make sure to match the
“+” and “-” ends of the bat-
teries with the diagram
inside the compartment.
Remote Control Operation Range.
You can use your remote control within a distance of 23 feet and an angle of 30 degrees
from the left and right sides of the PDP’s remote control receiver.

Antennas with 75-ohm Round Leads
If your antenna looks like this: it has 75-ohm round leads.
1Plug the antenna lead into the VHF/UHF terminal
on the PDP.
Use the antenna cable included in the product
package.

Connecting Cable TV
You can connect different cable systems to your PDP, including cable without a cable box,
and cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
1 Plug the incoming cable into the VHF/UHF terminal on
the PDP.
Use the antenna cable included in the product
package.
Cable with a Cable Box that Descrambles All Channels
1 Find the cable connected to the ANTENNA OUT
terminal on your cable box. This terminal might be
labeled "ANT OUT", "VHF OUT" or simply "OUT".
2Connect the cable to the VHF/UHF terminal on the
PDP.
Use the antenna cable included in the product
package.

Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1Find and disconnect the cable that is
connected to the ANTENNA IN terminal of
your cable box.
This terminal might be labeled "ANT IN",
"VHF IN" or simply, "IN". Connect this
cable to a two-way splitter.
2Connect a coaxial cable between an
OUTPUT terminal of the splitter and the
IN terminal of the cable box.
3Connect a coaxial cable between the
ANTENNA OUT terminal of the cable box
and the B-IN terminal of the A/B switch.
4Connect a coaxial cable between the
ANTENNA OUT terminal of the cable box
and the B-IN terminal of the A/B switch.
5Connect the last coaxial cable between the
OUT terminal of the RF (A/B) switch and
the VHF/UHF terminal on the PDP.
After you've made this connection, set the A/B switch to the "A" position for normal viewing.
Set the A/B switch to the "B" position to view scrambled channels. (When you set the A/B switch
to "B", you will need to tune your Set-Top Box to the cable box's output channel, which is usually
channel 3 or 4.)

Connecting a VCR
Connecting a VCR to the Video or S-Video/Audio jack
S-Video cable
Audio cable
Video cable
Power cord
Connect the video/audio cables between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the
PDP and VIDEO or S-VIDEO / L - AUDIO - R output jacks on the VCR. (Note: For better video,
use an S-Video cable.)
Note
•Please be sure to match the color coded input terminals and cable jacks.
Videotape Playback:
1. Turn on your PDP.
2. Press the SOURCE button to select “Video(AV1 or AV2)” or “S-Video”.
3. Turn on your VCR, insert a videotape and press the play button.
How to Connect
PDP VCR

Connecting a Camcorder
Connect a Video/Audio cable between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the
PDP and the VIDEO or S-VIDEO /AUDIO output jacks on the camcorder. (Note: For better
video, use an S-VIDEO cable.)
Note
•Please be sure to match the color-coded input terminals and cable jacks.
Viewing Tapes
1. Turn on your PDP.
2. Press the SOURCE button to select “Video(AV1 or AV2)” or “S-VIDEO”.
3. Turn on your camcorder and set it to Video Mode. (For details, refer to your camcorder
Owner’s instructions.)
4. Set the IN/OUT switch on your camcorder to OUT.
5. Insert the tape into the camcorder and press the Play button.
How to Connect
Viewing camcorder tapes
S-Video cable
Audio cable
Video cable
Power cord
PDP Camcorder

Connecting a DVD Player (480i, 480p)
This PDP displays the optimum picture in 720p mode.
Playing DVD
Connect a video cable between the Y, Pb, Pr(COMPONENT1, 2) input jacks on the PDP
and Y/PB/PRoutput jacks on the DVD player.
Connect an audio cable between the AUDIO L/R(COMPONENT1, 2) input jacks on the PDP
and the AUDIO output jacks on the DVD player.
Note
•Please be sure to match the color-coded input terminals and cable jacks.
To Play DVD:
1. Turn on your PDP.
2. Press the SOURCE button to select “COMPONENT1” or “COMPONENT2”.
3. Turn on your DVD player, insert a DVD disc and press the Play button.
• For an explanation of Component video, see your DVD owner’s instructions.
How to Connect
1
2
Component cable
Audio cable
Power cord
PDP DVD Player

Watching DTV
Connect the cable or antenna to the antenna input jack on the DTV.
Connect a video cable between the Y, Pb, Pr(COMPONENT 1, 2) or DVI jack on the PDP
and the Y, PB, PR(COMPONENT) or DVI output jacks on the DTV receiver.
Connect an audio cable between the COMPONENT 1, 2 (L/R AUDIO) or DVI (L/R AUDIO)
jacks on the PDP and the AUDIO OUTPUT jacks on the DTV receiver.
Notes
•Please be sure to match the color-coded input terminals and cable jacks.
•Connecting a PC using the DVI connection is not supported.
To Watch DTV:
1. Turn on your PDP.
2. Press the SOURCE button to select “COMPONENT1”, “COMPONENT2” or “DVI”.
3. Turn on your DTV receiver.
• For an explanation of Component video, see your DTV receiver owner’s instructions.
How to Connect
1
2
3
Use a DVI-D video cable. (sold separately)
Audio cable
Component cable
DVI cable
Power cord
PDP
DTV Receiver
or