Samsung series 6 650 User manual

Contact SAMSUNG WORLD-WIDE
ifyou have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant ies produits Samsung, veuillez contacter ie Service
Consommateurs Samsung.
U.S.A
CANADA
1-800-SAMSUNG(726-7864) www.samsung.com/us
1-800-SAMSUNG(726-7864) www.samsung.com/ca
i Samsung Electronics America, Inc. 105 Challenger Road
iRidgefield Park, NJ 07660-0511
iSamsung Electronics Canada Inc., Customer Service 55
Standish Court Mississauga, Ontario L5R 4B2 Canada
i Samsung Electronique Canada Inc., Service a la Clientele
55 Standish Court Mississauga, Ontario L5R 4B2
Canada
BN68-02269B-00

iImportantWarrantyinformationRegardingTelevisionFormatViewing
Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide
screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format,
or expanded to fill the screen ifyour model offers this feature and the images are constantly moving. Displaying stationary
graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and
programming, should be limited to no more than 5% ofthe total television viewing per week.
Additionally, viewing other stationary images andtext such as stock market reports, video game displays, station Iogos,
web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary
images that exceed the above guidelines can cause uneven aging of PDP Displays that leave subtle, but permanent
burned-in ghost images in the PDP picture. To avoid this, vary the programming and images, and primarily display
full screen moving images, not stationary patterns or dark bars.
On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture.
Be careful in the selection and duration of television formats used for viewing. Uneven PDPaging as a result of format
selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.
U.S,A Only
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties.
In particular, this product is licensed under thefollowing US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396,
5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and
under US Published PatentApplication No. 2001-44713-A1.
This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for
commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any
unlicensed product unit or process conforming to ISO/IEC 11172-3or ISO/IEC 13818-3 used or sold in combination with this product
unit. The license only covers the use ofthis product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3
or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC
11172-3or ISO/IEC 13818-3.
J
Other countries
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This
license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial
use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed
product unit or process conforming to ISO/IEC 11172-3or ISO/IEC 13818-3 used or sold in combination with this product unit. The
license only covers the use ofthis product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3or ISO/IEC
13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3or
ISO/IEC 13818-3.
© 2009 Samsung Electronics Co., Ltd.All rights reserved.

User instructions
0Screen image retention
Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as itcan cause
screen image retention. This image retention is also known as"screen burn". To avoid such image retention, referto page 26 of this
manual to reduce the degree of brightness and contrast of the screen when displaying a still image.
Altitude
The PDP can only operate normally at heights under 6500ft.
Heat on the top of the Plasma TV
The topside of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole inthe upper
part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
The product is making a 'cracking' noise.
A'cracking' noise may occur when the product contracts or expands dueto a change in the surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.
@ Cell Defects
The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to
produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the
product.
Avoid operating the TV at temperatures below 41°F (5°0)
A still image displayed too long may cause permanent damage to the PDP Panel,
Watching the Plasma TV in 4:3 format for a long period of time may leave traces of borders displayed on
the left, right and center of the screen caused by the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effects to the screen.
Damages caused by the above effect are not covered by the Warranty.
J
After=images on the Screen,
Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.
To prevent this effect, reduce the 'brightness' and 'contrast' when displaying still images for a long time.
Warranty
Warranty does not cover any damage caused by image retention.
Bum-in is not covered by the warranty.

Contents !
,,, List of Features.......................................................................... 5
,,, Checking Parts .......................................................................... 5
,,, Assembling the Cables.............................................................. 5
,,, Viewing the Control Panel ......................................................... 6
,,, Viewing the Connection Panel................................................... 7
,,, Remote Control ......................................................................... 8
,,, Connecting VHF and UHF Antennas ......................................... 9
,,, Connecting Cable TV ................................................................ 9
,,, Connecting a DVD/Blu-ray Player or Cable Box /Satellite
receiver (Set-Top Box) via HDMI............................................. 11
,,, Connecting a DVD/Blu-ray Player or Cable Box /Satellite
receiver (Set-Top Box) via DVl ................................................ 11
,,, Connecting a DVD/Blu-ray Player or Cable Box /Satellite
receiver (Set-Top Box) via Component cables ........................ 12
,,, Connecting a Camcorder ........................................................ 12
,,, Connecting a VCR................................................................... 13
,,, Connecting a Digital Audio System ......................................... 14
,,, Connecting an Amplifier /DVD HomeTheater ........................ 14
m Connecting a PC..................................................................... 15
,,, Turning the TV On and Off ...................................................... 16
,,, Changing Channels ................................................................. 16
,,, Adjusting the Volume............................................................... 16
,,, Using the TOOLS Button......................................................... 17
,,, Using the Remote Control Backlight Buttons .......................... 17
,,, Viewing the Display ................................................................. 17
,,, Viewing the Menus .................................................................. 18
,,, Plug & Play Feature ................................................................ 19
,,, Storing Channels .................................................................... 20
,,, Managing Channels ................................................................ 21
,,, Changing the Picture Settings ................................................. 23
,,, Using Your TV as a Computer (PC) Display............................ 27
,,, Display Modes......................................................................... 27
,,, Setting up the TV with your PC ............................................... 28
,,, Changing the Sound Settings.................................................. 29
,,, Configuring the Setup Menu.................................................... 30
,,, Viewing the Picture in Picture (PIP)......................................... 33
,,, Setting the Time ...................................................................... 34
,,, Source List /Edit Name........................................................... 35
,,, Support .................................................................................... 36
,,, Connecting a USB Device ....................................................... 38
,,, Using the Media Play Function................................................ 39
Symbol A
!
Press Note
,,, Using and Sorting Photo List................................................... 40
,,, Viewing a Photo or Slide Show .............................................. 41
,,, Using and Sorting the Music List............................................. 43
,,, Playing a Music ...................................................................... 44
,,, Using and Sorting the Movie List............................................. 45
,,, Playing a Movie File ............................................................... 46
,,, Picture /Music Settings Using Media Play.............................. 48
= Usingthe Setup Menu ............................................................. 49
,,, Setting the DLNA Network....................................................... 50
,,, Installing the DLNAApplication ............................................... 50
,,, Usingthe DLNAApplication .................................................... 52
,,, Usingthe DLNA Function........................................................ 55
,,, Connecting Anynet+ Devices .................................................. 56
,,, Setting UpAnynet+ ................................................................. 57
,,, Switching between Anynet+Devices ....................................... 57
,,, Recording................................................................................ 58
,,, Listening through a Receiver................................................... 59
,,, Troubleshooting forAnynet + ................................................... 59
,,, Activating the Content Library ................................................. 60
m Usingthe Content Library........................................................ 61
,,, Network Connection ................................................................ 62
m Network Setup ......................................................................... 65
,,, Getting Started with Internet@TV ........................................... 69
,,, Editing Snippets in the Dock ................................................... 71
,,, Usingthe Profile Widget .......................................................... 71
,,, Usingthe Yahoo(@Widget Gallery.......................................... 73
,,, Usingthe Yahoo(@Weather Widget ........................................ 74
,,, Usingthe Yahoo(@News Widget ............................................ 74
,,, Usingthe Yahoo(@Flickr Widget............................................. 75
,,, Usingthe Yahoo!® Finance Widget......................................... 76
,,, Troubleshooting for internet@TV ........................................... 76
aHelp Website ........................................................................... 77
,,, Home Network Center ............................................................. 78
,,, Setting Up the Home Network Center ..................................... 79
,,, Usingthe Message Function................................................... 80
,,, Usingthe Media Function........................................................ 81
,,, Troubleshooting ....................................................................... 82
,,, Preparation before installing the Wall-Mount........................... 83
,,, How to attach the Stand-Base ................................................. 83
,,, Securing the TV to the Wall..................................................... 84
,,, Wall Mount Kit Specifications (VESA) ..................................... 85
,,, Specifications .......................................................................... 86
,,, Dimensions (PN50B650SlF) .................................................. 87
,,, Dimensions (PN58B650SIF) .................................................. 88
One-Touch Button TOOLS

Connecting and Preparing Your TV
List of Features
o
o
o
o
o
Adjustable picture settings that can be stored in the TV's memory.
Automatic timer to turn the TV on and off.
A special sleep timer.
V-Chip function.
Excellent Digital Interface & Networking :
With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with noCable Box/Satellite receiver (Set-Top Box)
needed.
HDMI/DVl connection of your PCto this TV.
Excellent Picture Quality
SRS TruSurround HD provides a virtual surround system.
Media Play:Allows you to play music files, pictures, and movies saved on a USB or DLNA device.
Internet@TV: You can use various intemet services and view useful information and entertaining content.
Home Network Center: Allows you to configure a mobile message server or a DLNA media render.
Checking Parts
Please make sure the following items are included with your TV, If any items are missing, contact your dealer.
The items' color and shape +nayvary depending on the model.
Remote Control Power Cord Owner's Instructions /Warranty Card /Cleaning Cloth Holder-Wire TV-Holder /Screw
(BN59-00854A)/ (3903-000144) Quick Setup Guide Safety Guide Manuat (BN63-01798B) Cable (BN96-10788A)
AAA Batteries (BN68-01923A) (Not available in all (Referto page 84)
(4301-000103) locations)
Program CD Ferrite Core for Ferrite Core for Cover-Bottom Cover-Bottom/Screw (2ea)
Power Cord Side-AV (Referto page83) (Referto page83)
(3301-001305) (3301-001201 ) (PN50B650S1F only) (PN58B650S1F only)
(PN58B650S1F only)
Holder-Ring(4ea) Screw (4ea)
(Refer to page83) (PN50B650S1Fonly)
Ferrite Core
The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core andclip it around the cable near the
plug.
Assembling the Cables
Enclose the cables in the Holder-Wire Cable so that the cables are not visible through the
transparent stand.

Viewing the Control Panel
The buttons on the lower-right panel control your TV's basic features, including the on-screen menu.
To use the more advanced features, you must usethe remote control.
The product color and shape may vary depending onthe model.
The front panel buttons can be activated by touching them with your finger.
O SOURCED
Toggles between all the available input sources
(TV, AVI, AV2, Component1, Conponent2, PC, HDMII, HDMI2/DVI, HDMI3, HDMI4, USB).
Inthe on-screen menu, use this button as you use the ENTER_ button on the remote control.
O MENU
Press to see an on-screen menu of your TV's features.
O + VOL =
Press to increase or decrease the volume. In the on-screen menu, use the + VOL - buttons as you would use the
and !_ buttons on the remote control.
ACHV
Presstochangechannels.Intheon-screenmenu,usetheA CH V buttonsas youwoulduse theA and T buttonsonthe
remotecontrol.
O POWER INDICATOR
Blinks and turns offwhen the power is on and lights up in stand-by mode.
O (5 (POWER)
PresstoturntheTVonandoff.
O REMOTE CONTROL SENSOR
Aim the remote control towards this spot onthe TV.
O SPEAKERS

Viewing the Connection Panel
Usethe connectionpaneljackstoconnectA/Vcomponentsthatwillbeconnectedcontinuously,suchas Blu-ray/DVDplayers
or aVCR.
The product color and shape may vary depending onthe model.
TV Rear Panel TV Side Panel
EX-I INK T
:ANT IN
®
0
m@
OPOWER IN
Connects the supplied power cord.
OLAN
Connect a LAN cable to this port to connect to the
Network(Internet@TV).
AUDIO OUT (R/L)
Audio outputs to external devices.
@ PCIN[PC]/[AUDIO]
Connects to the video and audio output jacks on your PC.
Ifyour PC supports an HDMI connection, you can
connect this to the HDMI IN I, 2, 3, or 4 terminal.
Ifyour PC supports a DVI connection you can connect
this tothe HDMI IN 2 /DVIAUDIO IN [R-AUDIO-L]
terminal.
DVI AUDIO IN (AUDIO-R/L)
Connect to the DVI audio output jack of anexternal device.
HDMI IN 1, 2(DVI), 3, 4
Connect to the HDMI jack of a device with an HDMI output.
Use an HDMI cable which is smaller than 14.4mm.
What is HDMI?
•HDMl(High-Definition Multimedia Interface), is an
interface that enables the transmission of digital audio
and video signals using a single cable.
• The difference between HDMI and DVI is that the
HDMI device is smaller in size and has the HDCP
(High Bandwidth Digital Copy Protection) coding
feature installed.
• We recommend that 14.4mm is proper for cable size.
This is smaller than standard.
@
0
0
@
@
@
ANT IN
Uses a 75£2Coaxial connector for an Air/Cable Network.
DIGITAL AUDIO OUT (OPTICAL)
Connects to a Digital Audio component.
COMPONENT IN 1, 2/AV IN 1
Connects Component video /audio. The COMPONENT IN I
jack is also used as the AV IN 1 jack.
@ Connect the video cable to the COMPONENT IN 1
[Y/VIDEO] jack and the audio cable to the COMPONENT
IN 1[R-AUDIO-L] jacks.
EX=LINK
Used for service only.
us8 1(aDD)/USB2
Connect a USB mass storage device to view photo files and
play audio files.
@ The USB 1port is also used as the HDD. HDD (Hard disk
drive) is device which stores digitally encoded data.
AM IN2
Video and audio inputs for external devices.

Remote Control
You can use the remote control up to a distance of about 23 feet from the TV.
The product color and shape may vary depending on the model.
The performance of the remote control may be affected by bright light.
O
0
0
O
0
0
@
POWER
Turns the TV on and off. @
TV
Setects the TV mode directly.
NUMERIC BUTTONS
Press to change the channel.
Press to select additional channels (digital
and analog) being broadcast by the same
station. For example, to select channel
"54-3", press "54", then press "_" and "3".
_MUTE
Press to temporarily cut off the sound.
+-VOL :,-_
Press to increase or decrease the volume.
SOURCE
Press to display and select the available
video sources.
Q OH LIST
Used to display Channel Lists on the screen. _)
QTOOLS
Use to quickly select frequently used
functions.
_) UP& /DOWNT /LEFT4 /_)
RIGHTII_ /ENTER_
Use to select on-screen menu items and
change menu values. _)
(1) INTERNET@
This function enables you to view _)
Internet@TV.
_) COLOR BUTTONS
Use these buttons in the Channel list, _)
Media Play, and Intemet@TV, etc.
_) MEDIA.P (Media play) _)
This function enables you to view and play
photo and music files from an external
device. (Refer to pages 40 (Photo), 43
(Music) and 45 (Movie))
INFO
Press to display information on the TV
screen.
_) Use these buttons in the DMA, Media Play
and Anynet+ modes.
(_: This remote can be used to control
recording on Samsung recorders with the
Anynet+ feature)
_) _ON/OFF
Press to backlight the buttons on the remote.
This function is convenient for using at night
or when the room is dark. (Using the remote
control with the ON/OFF(_'_) light button set
to On will reduce the battery usage time.)
e PRE-CH
Tunes to the previous channel.
J
Press to change channels.
@ MENU
Disptays the on-screen menu.
FAV.CH
Press to switch to your favorite channels.
RETURN
Returns to the previous menu.
EXIT
Press to exit the menu.
RSIZE
Picture size selection.
CONTENT
This function enables you to view Content
Library.
CC
Controls the caption decoder.
MTS
Press to choose stereo, mono or Separate
Audio Program (SAP broadcast).
[3 Installing Batteries inthe RemoteControl
1. Lift the cover at the back of the remote control upward as shown in the figure.
2. Install twoAAAsize batteries.
Make sure to match the "+" and "-" ends of the batteries with the diagram inside the
compartment.
3. Close the cover as shown in the figure.
Remove the batteries and store them in a cool, dry place if you won't be using the
remote control for a long time. (Assuming typical TV usage, the batteries should last
for about one year.)
Using the remote control with the ONIOFF(_) light button set to On will reduce the battery usage time.
Ifthe remote control doesn't work, check the following
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Isthere a power outage or is the power cord unplugged?
5. Isthere a special fluorescent light or neon sign nearby?

Connections
Connecting VHF and UHF Antennas
if your antenna has a set of leads that look like this, see "Antennas with 300 _Flat Twin
Leads" below.
if your antenna has one lead that looks like this, see "Antennas with 75 Q Round Leads".
if you havetwo antennas, see "Separate VHF and UHF Antennas".
i
C) Antennas with 300 QFiatTwinLeads
if you are using an off-air antenna (such as a roof antenna or rabbit ears) that has 300 Q
twin flat leads, follow the directions below.
1. Placethe wires from the twin leads under the screws on a 300-75 _ adapter (not supplied).
Use a screwdriver to tighten the screws.
2. Plug the adaptor into theANT IN terminal onthe back of the TV.
I
[3 Antennas with 75 QRoundLeads
Plug the antenna lead into theANT IN terminal onthe back of the TV.
C3 Separate VHF and UHF Antennas
if you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV.This
procedure requires an optional combiner-adaptor (available at most electronics shops).
1. Connect both antenna leads tothe combiner.
2. Plug the combiner into the ANT IN terminal on the bottom of the back panel. I
Connecting Cable TV
To connect to acable TV system, follow the instructions below.
C) Cable without a Cable Box
Plug the incoming cable into the ANT INterminal on the back of the TV.
@ Because this TV is cable-ready, you do not need a cable box to view unscrambled cable
channels.
C) Connecting to a Cable Box that Descrambles All Channels
1. Findthe cable that is connected to theANT OUT terminal on your cable box.
This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".
2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.
ANT IN ANT OU_
Continued...

Connectingto a CableBoxthatDescramblesSomeChannels
if your cable box descrambles only some channels (such as premium channels), follow the instructions below. You
will need atwo=way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most
electronics stores.)
1. Findand disconnect the cable thatis
connected to the ANT IN terminal on your
cable box.
This terminal might be labeled "ANT IN",
"VHF IN" or simply, "IN".
2. Connect this cable to a two-way splitter.
Incoming
cable Splitter
3. Connect an Antenna cable between the
OUTPUT terminal on the splitter andthe IN
terminal on the cable box.
4. Connect an Antenna cable between theANT
OUT terminal on the cable box andthe B-IN
terminal on the RF(A/B) switch.
cable Splitter _==== _ _ ]
Cable Box
Splitter , RF (A/B)
Cable Box Switch
6. Connect another cable between the other
OUT terminal on the splitter and the A-IN
terminal on the RF (A/B) switch.
Cable Box Switch
6. Connect the last Antenna cable between the
OUT terminal on the RF (A/B) switch and the
ANT IN terminal on the rear of the TV. IN CABLE OUT
cable Splitter _
_ _ TV Rear
RF (A/S)
Switch
After you have made this connection, set theA/B switch to the "A" position for normal viewing. Set theA/B switch to the "B" position
to view scrambled channels. (When you set theA/B switch to "B", you will need to tune your TV to the cable box's output channel,
which is usually channel 3 or 4.)

Connecting a DVD /Blu-ray Player or Cable Box /Satellite receiver
(Set-Top Box)via HDMI
This connection can only be made if there isan HDMI Output jack on the external device, This connection will provide the
highest quality picture,
1. Connect an HDMI Cable between the HDMI IN (I, 2(DVI), 3, or 4)jack on theTV andthe HDMIjack on the DVD /Blu-ray Player or
Cable Box /Satellite receiver (Set-Top Box).
DVD/Blu-ray Player or Cable
Box /Satellite receiver
TV Rear Panel TV Side Panel
_HDMI Cable (Not supplied)
What is HDMI?
•HDMI, or high-definition multimedia interface, isan interface that enables the transmission of digital audio and video signals
using a single cable.
• The difference between HDMI and DVl is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital
Copy Protection) coding feature installed.
Each DVD Player or Cable Box /Satellite receiver (Set-Top Box) has a different back panel configuration.
The TV may not output sound and pictures may be displayed with abnormal color when DVD/Blu-ray Player or Cable Box /
Satellite receiver supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no
sound, connect the HDMI cable to the HDMI IN 2(DVl)jack andthe audio cables to the DVl AUDIO IN [R-AUDIO-L] jacks on the
back of the TV. If this happens, contact the company that provided the DVD/Blu-ray Player or Cable Box tSatellite receiver to
confirm the HDMI version, then request an upgrade.
HDMI cables that are not 1.3 may cause annoying flicker or no screen display.
Connecting a DVD/Blu-ray Player or Cable Box /Satellite receiver
(Set-Top Box)via DVI
This connection can only be made if there isaDVlOutput jack on the external device,
1. Connect a HDMI/DVl Cable or DVI-HDMI Adapter between the HDMI IN 2(DVl) jack on the TV andthe DVl jack on the DVD/
Blu-ray Player or Cable Box/Satellite receiver (Set-Top Box).
2. Connect Audio Cables between the DVl AUDIO IN [R-AUDIO-L] jack on theTV and the DVD/Blu-ray Player or Cable Box/Satellite
receiver.
DVD/Blu-ray Player or Cable Box /TV Rear Panel
Satellite receiver
_.®, =9
Each DVD/Blu-ray Player or Cable Box /Satellite receiver (Set-Top Box) has a different back panel configuration.
When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match the color of the connection terminal to the
cable.
When using an HDMI /DVl cable connection, you must use the HDMI IN 2(DVl)jack.

Connecting aDVD /Blu-ray Player or Cable Box /Satellite receiver
(Set-Top Box) via Component cables
The rear panel jacks on your TV make it easy to connect aDVD/Blu=ray Player or Cable Box ISatellite receiver (Set-Top Box) to
your TV,
1. Connect Component Cable between the COMPONENT IN (1 or 2) [Y, PB,PR]jacks onthe TV andthe COMPONENT [Y,PB,PR]
jacks onthe DVD/Blu-ray Player or Cable Box /Satellite receiver(Set-Top Box).
2. Connect Audio Cables between the COMPONENT IN (1 or 2) [R-AUDIO-L] jacks on the TV and theAUDIO OUT jacks on the DVD /
Blu-ray Player or Cable Box /Satellite receiver (Set-Top Box).
"IV Rear Panel
DVD /Blu-ray Player or Cable Box
/Satellite receiver
Component video separates the video into Y (Luminance (brightness)), PB(Blue) and PR(Red)for enhanced video quality. Besure
to match the component video and audio connections. For example, ifconnecting the video cable to COMPONENT IN 1,connect
the audio cable to COMPONENT IN I also.
Each DVD /Blu-ray Player or Cable Box /Satellite receiver (Set-Top Box) has a different back panel configuration.
When connecting a DVD /Blu-ray Player or Cable Box /Satellite receiver (Set-Top Box), match the color of the connection terminal
to the cable.
Connecting a Camcorder
The side and rear panel jacks on your TV make it easy to connect acamcorder to your TV,
_3 Usingan Video /Audio Cable
1. Connect a Video Cable between the AV IN2 [VIDEO]jack onthe TV and the VIDEO OUT jack on the camcorder.
2. Connect Audio Cables between theAV IN 2 [L-AUDIO-R] jacks on the TV and the AUDIO OUTjacks on the Camcorder.
Each Camcorder has a different back panel configuration.
TV Side Panel
Camcorder
_ Video Cable (Not supplied) r .... i_ i
_Audio Cable (Not supplied} --=_ I_,J
When connecting a Camcorder, match the color of the connection terminal to the cable.

[3 Usingan HDMICable
1. Connect an HDMI Cable between the HDMI IN (1, 2(DVI), 3, or 4) jack on the TV and the HDMIjack onthe camcorder.
Camcorder
TV Rear Panel
_HDMI Cable (Not supplied) Or _
TV Side Panel
iiiii/_i /
Each Camcorder has a different back panel configuration.
Connecting a VCR
_3 VideoConnection
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the
instructions on pages 9_10). Skip step 1 ifyou have not yet connected to an antenna or a cable system.
1. Unplug the cable or antenna from the back of theTV.
2. Connect the cable or antenna to theANT IN terminal onthe back of the VCR.
3. Connect an Antenna Cable between theANT OUT terminal on the VCR andthe ANT INterminal on the TV.
4. Connect a Video Cable between the AV IN 1 [Y/VIDEO] or AVIN 2 [VIDEO] jack on the TV and the VIDEO OUTjack onthe
VCR.
6. Connect Audio Cables between theAV IN 1 (or AV IN2) [R-AUDIO-L] jacks on the TV and the AUDIO OUTjacks on the VCR
VCR Rear Panel
TV Rear Panel TV Side Panel
Ifyou have a "mono" (non-stereo) VCR, use a Y-connector (not supplied) to connect to the rightand left audio input jacks of the
TV.Alternatively, connect the cable to the "R"jack.
Ifyour VCR is stereo, you must connect two cables.
Each VCR has a different back panel configuration.
When connecting a VCR, match the color ofthe connection terminal to the cable.
When connecting toAV IN I, the color of theAV IN I [Y/VIDEO]jack (Green) does not match thecolor ofthe video cable (Yellow).

Connecting a Digital Audio System
The rear panel jacks on your TV make it easy to connect aDigital Audio System(Home theater/Receiver) to your TV,
1. Connect an Optical Cable between the DIGITALAUDIO OUT (OPTICAL)jacks on the TV and the Digital Audio Input(OPTICAL)
jacks onthe Digital Audio System.
When a Digital Audio System is connected to the DIGITALAUDIO OUT (OPTICAL)jack : Decrease the volume ofthe TV, and
adjust the volume level with the system's volume control.
Digital Audio System
TV Rear Panel
5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.
Each Digital Audio System has a different back panel configuration.
When the receiver (home theater) is set to On, you can hear sound output from the TV's Optical jack. When the TV is displaying a
DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such
as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
Ifyou want to hear 5.1 channel audio, connect the DIGITALAUDIO OUT (OPTICAL) jack on the DVD /Blu-ray player or Cable/
Satellite Box directly to anAmplifier or Home Theater, notthe TV.
Connecting an Amplifier /DVD Home Theater
Connect Audio Cables between theAUDIO OUT [R-AUDIO-L] jacks on the TV and AUDIO IN [L-AUDIO-R] jacks on the Amplifier/
DVD HomeTheater.
When an audio amplifier is connected to the AUDIO OUT [R-AUDIO-L]jacks terminals : Decrease the volume of the TV, and adjust
the volume level with theAmplifier's volume control.
Amplifier /DVD Home Theater
TV Rear Panel
(Not supplied)
EachAmplifier /DVD Home Theater has a different back panel configuration.
When connecting anAmplifier /DVD Home Theater, match the color of the connection terminal to the cable.

Connecting a PC
[_ Usinga D-SubCable
1. Connect a D-Sub Cable between PC IN [PC]jack on the TV and the PC output jack on your computer.
2. Connect a PCAudio Cable between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your
computer.
PC
TV Rear Panel
I1
i/_iii/
_PC Audio Cable (Not supplied}
_ D-Sub Cable (Not supplied)
Usingan HDMI/DVICable
1. Connect an HDMI/DVI cable between the HDMI IN 2(OVl)jack on the TV and the PC output jack on your computer.
2. Connect a 3.5 mm Stereo plug to 2RCA cablebetween the DVIAUDIO IN[R-AUDIO-L]jack onthe TV andtheAudio Out jack of
the sound cardon your computer.
TV Rear Panel
PC
3.5 mm Stereo plug to 2RCA Cable (Not supplied}
_ HDMI/DVI Cable (Not supplied)
Each PC has a different back panel configuration.
When connecting a PC, match the color of the connection terminal to the cable.
When using an HDMI/DVl cable connection, you must use the HDMI IN 2(DVl) terminal.

i Operation i
Turning the TV On and Off
Press the POWER button on the remote control, You can also use the POWER button
on the TV,
Itmay take a while for your TV to power on.
Changing Channels
C)
C)
C)
C)
Usingthe Channel Buttons
Press the CH l_ or CH _',-_ button to change channels.
When you press the CH [w or CH _j button, the TV changes channels in
sequence. You will see all the channels that the TV has memorized. (The TV must
have memorized at least three channels). You will not see channels that were either
erased or not memorized. See page 20 to memorize channels.
Using the Number Buttons
Press the number buttons to go directly to a channel. For example, to select channel "27",
press "2",then "7".
For quick channel change, press the number buttons, then press the ENTER_
button.
Using the "_ j" Button
The" -_" button is used to select stations that broadcast a digital signal.
For example, for Channel "7-1", press "7", then '",- ;",then "1".
For quick channel change, press the number buttons, then press the ENTER_
button.
Usingthe PRE-CHButton to select the Previous Channel
Use the number buttons to quickly tune to any channel. Press the PRE-CH button. The
TV will switch to the last channel viewed.
To quickly switch between two channels that are far apart, tune to one channel, then
use the number button to select the second channel. Then use the PRE-OH button
to quickly alternate between them.
= MUTE
Adjusting the Volume
C)
C)
Using the Volume Buttons
PresstheVOL -+ orVOLi= buttontoincreaseor decreasethevolume.
Usingthe MuteButton
At any time, you can cut off the sound using the =_<MUTEbutton.
1. Press AMUTE button and the sound cuts off.
will displayed onthe screen.
2. To turn mute off, press the AMUTE button again, or simply press the VOL +i or
VOL :- i button.
,"i.......................1............. I =,....................Ji"

Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes
depending on which external input mode you are viewing,
i. Press the TOOLS button. The Tools menu will appear.
2. Press the A/T button to select a menu, then press the ENTER_ button.
3. Press the A/T/_I/_/ENTER_ buttons to display, change, or use the selected items.
For a more detailed description of each function, refer to the corresponding page.
Anynet+ (HDMI-CEC), see page 57
Picture Mode, see page 23
Sound Mode. see page29
Sleep Timer, see page 34
SRS TS HD. see page 29
Add to Favorite (or Delete from Favorite), see page 21
Switch to Cable (or Air), see page 2C
PIP. see page 33
Auto Ac,ustment. see page 28
Using the Remote Control Backlight Buttons
Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.
1. Press the ON/OFF(_)light button
When ON, the button backlight is turned on for a moment.
Pressing a remote control button when the remote control is on turns the button backlight on for a moment.
Ifyou touch or move the remote control andthe motion is detected by the sensor of the remote control, the button backlight will
beturned on for a moment.
@ The button backlight will not beturned on when the remote control is turned off.
Viewing the Display
The display identifies the current channel and the status of certain audio-video settings,
1. Press the mNFObutton on the remote control. The TV will display the channel, the type of
sound, and the status of certain picture and sound settings.
Press the INFO button once more or wait approximately 10 seconds and it disappears
automatically.

Viewing the Menus
Before using the TV,follow the steps below to learn how to navigate the menu in order to select and adjust different functions.
1. Press the MENU button.
The main menu is displayed on the screen. Its left side has the following icons: Picture, Sound, Channel, Setup, Input,
Application, Support.
2. Press the A or T button to select one of the icons.
Press the _ or _- button to access the icon's sub-menu.
3. Press the A or T button to move to items in the menu.
Press the ENTERIC, button to enter items in the menu.
4. Press the A/T/_/_- button to change the selected items.
Press the RETURN button to return to the previous menu.
6. Press the EXiT button toexit from the menu.
Using the remote control buttons
[_ Example:Setting the TV's Brightnessinthe PictureMenu
Adjusting the Brightness to 80
1. Press the MENU button to display the menu.
2. Press the ENTERIC, button to select Picture.
3. Press the ,_.or Vbutton to select Brightness.
4. Press the ENTER[_q_button.
6. Press the 4 or _. button until the Brightness changes to 80.
6. Pressthe ENTERIC, button.
Press the EXIT button to exit from the menu.

Plug & Play Feature
1.
The first time you turn on your new TV, choose your basic settings for language, input source and channels, and time of day
using the plug &play feature. The TV will store these settings in memory. Storing the channels in memory will allow you to
scan the stored channels rather than have to enter their digits each time you want to change channels.
The Screen Saver is activated if there is no remote control key input for longer than I minute while Plug & Play is running.
The Screen Saver is activated if there is no operating signal for longer than 15 minutes.
6.
7.
8.
Press the POWER button on the remote control.
Select Language of the OSD menu is automatically displayed. Select the appropriate
language by pressing the ,& or T button. Pressthe ENTER_ button to confirm your
choice.
Press the _ or _ button to select Store Demo or Home Use, then press the
ENTER_ button.
We recommend setting the TV to Home Use mode for the best picture in your home
environment.
Store Dome mode is only intended for use in retail environments.
Ifthe unit is accidentally set to Store Dome mode and you want to return to Home
Use (Standard): Press the Volume button on the TV.When the volume OSD is
displayed, press and hold the MENU button on the TV for 5 seconds.
Press the A or T button to select the Antenna source to memorize. Press the
ENTER_ button to select Start.
•Air: Air antenna signal.
• Cable: Cable antenna signal.
•Auto: Air and Cable antenna signals.
In Cable mode, you can select the correct signal source among STD, HRC, and
IRC by pressing the A, _r, 4 or _- button, then press the ENTERI_ button. If
you have Digital cable, select the cable system signal source for bothAnalog and
Digital. Contact your local cable company to identify the type of cable system that
exists in your particular area.
The TV will begin memorizing all of the available channels.
To stop the search before it has finished, press the ENTER_ button with Stop
selected.
After all the available channels are stored, it starts to remove scrambled channels. The Auto program menu then reappears.
Press the ENTERI_ button when channel memorization is complete.
The message Set the Clock Mode, is displayed. Press the ENTER_ button.
Press the A or T button to select Auto, then Press the ENTER_ button. The message Set to daylight saving time, is displayed.
Ifyou select Manual, Set current date and time is displayed. For detailed descriptions about the Manual, refer to page 34.
Press the A or V button to select Off, On, or Auto, then press the ENTER_ button.
The image to select time zone in which you live is automatically displayed.
Press the A or _' button to Select the time zone, then press the ENTERIC, button.
Ifyou have received a digital signal, the time will be set automatically. If not, see page 34to set the clock.
The brief instruction on How to get the best performance from your new HDTV is displayed.
Press the ENTERIC, button.
You can change to the previous or next page by pressing the 4 or _, button.
You can access the HD Connection Guide in the Support menu.
The message Enjoy your TV, is displayed.
Ifyou want to view the TV immediately, select the Watch TV.
Ifyou want to view the See Product Guide, press the ENTERIC, button.
If you want to reset this feature...
1. Press the MENU button to display the menu. Pressthe ,i, or T button to select Setup,
then press the ENTERI_q_button.
2. Press the ENTERI__}j button again to select Plug & Play. For further details on setting up
options, press the ENTERI_q_button again.
The Plug &Play feature is only available in the TV mode.

Channel Control
Storing Channels
[3 Antenna_Air/Cable
Before your television can begin memorizing the available channels, you must specify
the type of signal source that is connected to theTV (i.e. anAir or a Cable system).
_3
_3
_3
You can also switch the airtcable by selecting Tools -_ 8witch to Cab!e (orAir)
AutoProgram
• Air: Air antenna signal.
• Cable: Cable antenna signal.
• Auto: Air and Cable antenna signals
When selecting the Cable TV system: Selects the cable system. 8TD, HRC and IRC identify various types of cable TV systems.
Contact your local cable company to identify the type of cable system that exists in your particular area.At this point the signal
source has been selected.
After all the available channels are stored, it starts to remove scrambled channels.
The Auto program menu then reappears.
Ifyou want to stop Auto Programming, press the ENTER_ button.
The Stop Auto Program? message will be displayed. SelectYes by pressing the 4 or i_ button, then press the ENTERIC,
button.
ClearingScrambled Channel (Digitalchannelsonly)
The Clear Scrambled Channel function is used to filter out scrambled channels after Auto Program is completed.
This process may take up to 20~30 minutes.
To stop searching scrambled channels: Press the ENTERIC, button to select Stop.
Press the _1button to select Yes, then press the ENTER_ button.
This function is only available in Cable mode.
FineTune(Analogchannelsonly)
Ifthe reception is clear, you do not have to fine tune the channel, as this is done
automatically during the search and store operation. If the signal is weak or distorted,
you may have to fine tune the channel manually.
Finetuned channels that have been saved are marked with an asterisk * on the
right-hand side of the channel number in the channel banner.
Ifyou do not store the fine-tuned channel in memory, adjustments are not saved.
To reset the fine tuning setting, press the T button to select Reset, then press the ENTER_ button.