• Allow your refrigerator to operate and
cool down for 24 hours (1 full day) be-
fore the ice maker starts producing ice.
• To ll the ice bucket to maximum ca-
pacity, dispense a few cubes 8 and 16
hours after installation.
• If ICE OFF is lit, the ice maker will not make ice.
• To activate the ice maker, press the ICE OFF but-
ton on the control panel so it is no longer lit.
• If you have the model RF268, RFG238 or
RFG298, the gure may differ slightly from your
refrigerator. For details, refer to the “Using the
Control Panel” section of the User Manual.
3 sec
• Recommended Temp Settings
: -2°F for freezer and 38°F for refrigerator.
• Filter indicator : The lter Indicator will be Red
when you have used your water lter for 6 months,
Reset the indicator (it will be Blue) after replacing
the lter by holding the "Alarm/Hold 3 sec for
Filter Reset" button for 3 seconds.
• Ice off : Press the "Ice Off" button to turn the ice
making function off.
• Cooling Off (Show Room) mode : If the Display
shows the "0F 0F" code, it means that the Cool-
ing Off function is activated and the refrigerator is
not cooling. To cancel the Cooling Off mode, hold
the Energy Saver + Freezer buttons together for
3 seconds.
Display
• When installing, servicing or cleaning behind the
refrigerator, be sure of the following:
• To protect your oor's nish when moving the
refrigerator, cut a large section of the cardboard
carton and place under the refrigerator where
you are working.
• Pull the unit straight out and push back in straight
after nishing.
Moving and Installing
PUSH
• Check if the ice bucket is completely
inserted.
• Freezer temp may not be enough;
set it to -2°F or lower.
Slow Ice cube freezing
• If the water lter is clogged, small or bubbled ice
cubes may be produced.
• Replace the water lter cartridge with a new one.
Small or bubbled ice cubes or Slow
water dispensing
After installation or when replacing the
water lter, dispense at least a gallon
(2~3minutes) of water to remove trapped
air from the water line. Otherwise, water
may drip after dispensing water.
• Slowly turn the water lter 90°
clockwise so it is aligned with the
printing mark on the cover, locking
the lter in position.
Make sure to align the water lter
label mark with center of cover l-
ter printing as illustrated.
Water filter replacement
• The rst glass of water may not be cold enough
because the stored water in the water valve has
not cooled completely. Dispense several glasses
of water and then it would be cool.
Water is not cool enough
• Allow your refrigerator to operate and cool down
for 24 hours (1 full day) to reach to the set tem-
perature.
• Also, when you put room temperature or warmer
food into your refrigerator, it may need an addi-
tional 24 hours for the fridge to reach the set tem-
perature.
Refrigerator or freezer Compartments
are warm
• If food with too much moisture is stored near the
cooling vents, it may get frozen. Be sure to keep
moist food away from the cooling vents.
Food stored in refrigerator is frozen
• Wipe off the condensation with a dry towel (This
may occur during hot and humid seasons.)
• If the condensation occurs on the doors, turn off
the Energy Saving function.
• If you open the doors frequently or for too long, it
may cause moisture inside the fridge.
Moisture forms on outside/inside of
refrigerator
• These noises may be heard occasionally inside
the refrigerator. This is normal. This sound occurs
when various items contract or expand while
temperatures are changing; especially during
defrosting. This may also occur when electronic
devices including the ice maker are operating.
Noise Clicks, Pops, Cracks, Snaps
• You can select your Pantry temperature from
among the following.
Fresh(38°F[3°C])
Chilled(34°F[0°C])
Deli(41°F[5°C]) modes.
Cool Select Pantry (on some models)
• Insert a at-blade screwdriver into a slot on the
control lever, turn it clockwise or counter-clock-
wise to level the
door.
Control Lever
Screwdriver
• Open the freezer drawer to gain an access to the
adjustable hinge pin. Next, adjust the refrigerator
door using the provided 0.16 inch wrench.
RAISE
• If you need to add more height to the door, insert
the provided snap rings.
Leveling & Door Alignment
• If the water line is not inserted into the coupler
properly, air could penetrate into the water line
causing water dripping from the water dispenser.
• CAUTION : Insert the water line into the coupler
completely and slide in the clip at the end of the
coupler.
Water dispenser dripping
Red Clip
(1/4")
Dispenser
Door Tube
Cabinet
Tube
If you have RF265, RF266F, RF268 or RFG299,
the gure may differ slightly from your Refrigerator.
For details, refer to the user manual “Using the
control panel”
DA99-01900A REV(0.4)
PUSH
