45
MAINTENANCE & CLEANING
Interior parts
Dismantle all shelfs, doorframes, trays, covers and drawers
and clean with a soft cloth that is soaked with water or medium
detergent (for bowl or chopstick wash).If detergent is used,
please clean with water first,then wipe with a piece of dry cloth.
Door gasket
If the door gasket contacts the oil or sauce etc.,it will be
impaired after a long time, especially for the gasket of the
door up and down.Make sure to cleanthe gasket carefully.
The recess shall be cleaned by the chopstick shrouded by
cotton piece.When embed thegasket, fit four corners first
and embed the gaskets section by section.
Defrost method
When the frost layer gets thick, it may impair the cooling effect. You may take out and pack
the foods. Pull out the power plug and wipe off the water with soft cloth when the frost layer
vanishes. Then connect to the power and restart the appliance to setup the temperature.
Generally once or twice defrost is required per year.
NOTES 1.Plug off the power first, then clean the freezer after defrost;
2.The best time to defrost is when the freezer is empty or half empty;
3.Do not use metal or sharp tools for defrost to prevent damage;
4.No electric heater is allowed for defrost;
Cleaning precautions
Pull out theplug from thesocket before cleaning,the interval between
plug in andout shall beover 5 minutes;
No water isallowed in thelamp and PCBcover during cleaning;
Wipe with softtowel dipped overwater or mediumdetergent, then clean
with dry cloth;
Do not usethe detergent withabrasive(e.g. Toothpaste),acid,chemical
solvent(e.g.alochol) or puttyagent.
NOTES
The following checks shall be made after maintenance:
Any chaps or scars are found on the power cord.
Plug in the socket reliably
The power plug gets hot or otheraccidents.
8
Change the lamp
Screw off the lamp cover, then hold the cover and pull left to remove the cover.
Plug out the power cord.
Turn off the bulb counterclockwise.
Turn on the bulb clockwise.
Push the right side of the lamp cover into the left recess of the temperature
controller, then turn on the screws.
Bulb parameters: ~220V-240V,25W,E14
INSTALLATION & SETUP
Place the refrigerator
1.Remove the footcushion prior touse.
2.If the applianceis placed unsteadily, you may adjust the front leg in the bottom to stablize
the appliance (liftby turning left).Thereis a adjusthole in thefront leg.You may adjustit
with a crossheadscrewdriver (see rightfigure).
3.The ground underthe appliance shallbe flat andsolid.
Otherwise noise andoscillation will arise.
The noise willgrow stronger ifthe
appliance is puton the softground;
Please put asolid plate onthe blanket,
to avoid miscoloror heat blocking;
Tostablize the appliance,please leave
the foot contactingthe ground closelyand
keep the applianceleaning back foreasy closing ofthe door.;
Packaging & handling
5
1.Unpacking, repacking andhandling
2.Do not holdthe door duringtransportation.
3.Avoid clash or acute shaking during handling.
Do remember wherethe packages areduring unpacking andexamining.
The products cannot be transporteduntil they arerepacked after examining.
Do not position the appliance reversely or horizontally.
If tilting is required, the tilting angle shall be less than45
Please handle the applianceas per the instructionsto
prevent from noise orsome other problems.
4.Vertical handling to avoid clash
WARNING - Keep ventilationopenings, in theappliance enclosure orin the build-instructure,
clear of obstruction.
- Do notuse mechanical devicesor other meansto accelerate thedefrosting process,
other than thoserecommended by themanufacturer.
- Do notdamage the refrigerantcircuit.
- Do notuse electrical appliancesinside the foodstorage compartments ofthe
appliance, unless theyare of thetype recommended bythe manufacturer.