Samsung SOC-4020 SERIES User manual

SAMSUNG CCD CAMERA
SOC-4020SERIES
LENS BUILT INCOLOR CCDCAMERA
INSTRUCTION MANUAL
About this manual
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
P/No. : 6806-0438-01B
VAN 04. 9
•SAMSUNG TECHWIN CO., LTD.
Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,
Jungwon-Gu,Sungnam,Kyungki-Do,Korea462-703
TEL:[phone]~41 FAX:[phone]
•SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)
Closed Circuit Division 40 Seaview Drive, Secaucus NJ 07094,
U.S.A
TEL: [phone] FAX:[phone]
•SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)
Samsung House, 1000 Hillswood Drive Hillswood Business
ParkChertseySurreyKT16OPS
TEL:[phone] FAX:[phone]
•
TIANJINSAMSUNGOPTO-ELECTRONICSCO.,LTD(TSOE)
7PingchangRd,NankaiDist, Tianjin, P.R China
PostCode:300190
TEL: [phone] FAX: [phone]
SALES NETWORK
www.samsungtechwin.com
www.samsungcctv.com

This installation should be made by a qualified service
person and should conform to all local codes.
INFORMATION -This equipment has been tested and
found to comply with limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly
approved by the manufacturer could void the user’s authority
to operate the equipment.
CAUTION -
To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
WARNING- TO PREVENT ELECTRIC SHOCK AND RISK OF FIRE HAZARDS,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Thank you for purchasing a SAMSUNG CCD CAMERA. Before
operating the camera, confirm the camera model and proper
input power voltage. In order that you can understand this
manual thoroughly, we'll introduce our model description.
SOC-4020 Series (410,000 pixels)
• NTSC models • PAL models
SOC- 4020ND SOC- 4020PD
SOC- 4020NA SOC- 4020PA
SOC- 4020NDW SOC- 4020PDW
SOC- 4020NAW SOC- 4020PAW
Model Description
SOC- 4020 X X X
• Signal System
N NTSC Model
P PAL Model
• Power Source
D DC 12V
A AC 24V ~
• Lens Type
Blank 3.8~9.5mm
W 2.5~6.0mm
Power Source
Signal System
Lens Type

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual
54
Features Contents
Auto Iris Vari-focal Lens Built-in
The focal length of lens is 3.8 to 9.5mm,
equivalent to 2.5x zoom.(2.5 to 6.0mm,
equivalent to 2.4x zoom) The built-in
lens allows the camera to have a Wider
Dynamic Range, therefore you can use
in various applications.
Fashionable and Stylish Design
Fashionable design is best suited to many
modern places moreover silver color adds
lusterto that.
High Resolution
The horizontal resolution of 480 TV lines
can be achieved by using a high density
CCD having effective 410,000 pixels,
which provides clean, noiseless and
reliablepictures.
Backlight Compensation
The backlight compensation technology
allows the camera to find the best picture
conditions in any environment and
automatically gives a necessary light level
compensation, so that you can always
obtain the clear picture, the finest detail
andperfect lightcontrast.
High Sensitivity
DSP LSI technology provides best picture
with min illumination of 0.5Lux / F1.2
(30IRE).
White Balance (ATW)
ATW function allow the camera to
adjust the white balance automatically
in response to light conditions.
SYNC. System
Youcan selectINT(Internal Synchronization)
modeor L.L(Linelock Synchronization)mode.
(SOC-4020SERIES)
Front
Back
Bottom
6
Lens
Connecting To Monitor
Connecting To Power
Precautions
8
Composition
9
14
14
15
10
9
13
Name and Function of Each Part
14
Connection
17
Troubleshooting
18
Specification

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual
76
Precautions
Do not install the camera in
extreme temperature conditions.
Only use the camera under conditions
where temperatures are between -10˚C
and +50˚C. Be especially careful to provide
ventilation when operating under high
temperatures.
Do not install or use the camera in an
environment where the humidity is high.
Itcancausetheimagequalitytobepoor.
Do not install the camera under
unstable lighting conditions.
Severe lighting change or flicker can
cause the camera to work improperly.
Do not touch the front lens of
the camera.
It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.
Do not drop the camera or
subject them to physical shocks.
It can cause malfunctions to occur.
Never keep the camera face to
strong light directly.
It can damage the CCD.
Do not expose the camera to
rain or spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.
• If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.
• Please check that the power satisfies the normal specification before connecting
the camera.
Notes

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual
98
Composition
1. Color CCD Camera SOC-4020
2. Instruction Manual
Front
Lens Built-in
Vari-focal Lens built-in camera.
Control Cover
Used to access focus or zoom handle. After access, be sure to close it.
Focus Handle
Used to providefor accurate focusing of an objectwithinthelensfieldofview.
Zoom Handle
Used to adjustzoommagnification by turning.
Name and Function of Each Part

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual
1110
Back
Video Out Jack
Connecttothevideo input connector of monitor. Thisjackoutputsa
composite video signal. Use a coaxial cable for connection.
DC Level Adjustment V.R
Used to adjust video output level of DC driven auto iris lens. When the
brightness control of the monitor does not operate correctly, you can get the
optimum picture by controlling the DC level of camera.
V. PHASE Adjustment V.R: AC type
If the camera is to be used in the LL mode, the vertical phase may require
adjustment to synchronize the vertical phase of the camera with other camera
in the system. Make this adjustment when the vertical phase of the camera
does not match with other cameras or systems. For correct adjustment, use a
multi-channeloscilloscope. The V. PHASE adjustment canbereadjusted.
Power Input Terminal
UsedtoconnectAC/DC power source.
Power Lamp
Thepowerlampturns on when power is properlysupplied.
Function Selection Switch
(1) BLC(Backlight Compensation) ON/OFF Switch
This switch improves an image that is darkened because of backlighting.
When the lighting source is in the rear of an object, the object might be seen
somewhat dark. If you want to see the object clearly, turn this switch ON.
The effective area where backlight compensation is activate is fixed in the
centerof the screen.
Monitor Picture Adjustment direction
To make it brighter Turn clockwise
Monitor Picture Adjustment direction
To make it darker
Turn counterclockwise
• This adjustment is necessary only when linelock is performed.
• There is no V. PHASE adjustment VR on the rear of DC power type.
Notes
Name and Function of Each Part
* Use the select switches on the rear of camera.
*This diagram is based on SOC-4020Series

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual
1312
Name and Function of Each Part
(2) White Balance Control Mode
•ATW(Auto Tracing White balance): The camera automatically controls the
white balance in any environment.
•AWC(Auto White balance Control): The white balance is automatically
adjusted in a specific environment.
(3) Sharpness
Theswitch emphasize the sharpness. Tosoften the edgeturn this switch off.
(4) Flickerless
Flickerless function. In this function, electronic shutter is fixed in 1/100sec
(1/120sec: PAL model). FL function can compensate the flicker caused by
power frequency, but set OFF in the area not using a 60Hz (50Hz: PAL
model)AC Power.
(5) INT/LL Switch: SOC-4020Series
Used to choose INT or LL mode.
•INT(Internal) mode :The camera may be operated independently with its
internal crystal control.
• LL(Linelock) mode : It synchronizes the video signal between cameras using
thefrequencyofthe AC power supply without external synchronousgenerator.
(6) Not Used
• The LL mode can be used in the areas of 60Hz(NTSC models), 50Hz(PAL models).
Notes
Bottom
You can remove and install this bracket on the top of
the camera. You must use the supplied screw or the
equivalent (within 6mm). If not, the bracket may not
be fixed properly.
Tripod Mounting Hole
Usedto install the camera onan optional tripod.
Thetripod must be equipped withthe screw
specifiedas shown below.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
L

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual
1514
Connection
LENS
TheDC lens is supplied withthis camera.
•Ifthe lensis markedwith fingerprintsor othermarks,the imagequality mightbe poor.
•It is recommended to use the built-in iris lens to improve the image quality under low
illumination.
Notes
Connect the VIDEO out jack to the monitor video in jack.
Connecting to Monitor
CCD Camera Monitor
•As the connecting method varies with the instruments, refer to the manual
supplied with the instrument.
• Connect the cable after power is turned off.
• Setthe75Ω/ Hi-Z selection switch asshown below ifyou have anintermediate device.
CCD Camera Intermediate End monitor
Connecting to Power
Each model has different power specification, please check the name of the model
and power specification before connecting to power source.
Please refer to the sticker identifying the model, which is attached on the product,
for power specification.
• The wire is polarized. Be careful of polarity.
• Use DC 12V power source for SOC-4020SERIES
Resistance of copper wire [at 20C˚ (68˚F)]
•As voltage may drop according to the length of electric cord as above table, a
cameramay malfunction if too longoutput line ofadaptor is connected to the
camera.
* Voltage for camera operation: DC 12V ± 10%
* Voltage drops on above table are variable according to types of electric cord and makers.
For DC Power Type
Copper wire size (AWG) #24(0.22mm2)#22(0.33mm2)#20(0.52mm2)#18(0.83mm2)
Resistance ( Ω/ m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual
1716
Connection
• The wire is non-polarized.
• Use AC24V ~ 60Hz power source for SOC-4020NA/W
• Use AC24V ~ 50Hz power source for SOC-4020PA/W
For AC Power Type
• Be sure to connect power after all the installation is done.
• Note that AC adaptor is not supplied with camera.
• Use only AC 24V UL listed class 2 power supply.
• Since the wire of DC power type is polarized, be careful when connecting it.
• Do not use power sources other than that specified.
• To prevent fire or electric shock hazard, use a UL listed cable (VW-1, Style 1007).
Notes
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
Problem
Nothing appears on
the screen.
The image on the
screen is dim.
The image on the
screen is dark.
The camera is not working
properly, and the surface
of the camera is hot.
The image on the
screen flickers.
L/L mode isn’t able to
be selected.
Solution
•Check that the power cord and line connection
betweenthe camera andmonitorare fixedproperly.
•Check that you have properly connected VIDEO
cabletothecameraVIDEO output jack.
•Is lens stained with dirt? Clean your lens with soft,
clean cloth.
• Set the monitor to proper condition.
•If the camera is exposed to too strong light, change
the camera position.
• Adjust the lens’ focus properly.
•Adjustthecontrastfeatureofthemonitor.
•If you have an intermediate device, set the 75Ω/ Hi-z
properly.(refer topage14)
•AdjustDCLevel,VR Level properly (refer to page 10)
•Check that you have properly connected the camera
to an appropriate power source. (refer to page 15)
• Is the camera facing to direct sunlight or fluoresent
lighting? Change the camera position.
•Have you connected your camera to DC power
source? Connect it to AC power source.
(SOC-4020Series)
Troubleshooting

COLORCCD CAMERA User’s Manual
18
COLORCCD CAMERA User’s Manual
18
Specifications
SOC-4020NA/W SOC-4020ND/W SOC-4020PA/W SOC-4020PD/W
Item
Power Source
Power Consumption
Synchronization
Image Pick-up Device
Total Pixels
Effective Pixels
Scanning
Min. Illumination
Resolution
Video Output
Scanning Frequency
AGC
White Balance
BLC Function
Sharpness
Flickerless
Lens Type
S/N Ratio
Operating Temperature
Dimention
Weight (Without Lens)
INT/LL Selectable
(0~270˚ Adjustable)
INT
INT/LL Selectable
(0~270˚ Adjustable)
INT
AC 24V, 60Hz DC 12V AC 24V, 50Hz DC 12V
3.5W (Max) 2.5W (Max) 3.5W (Max) 2.5W (Max)
1/3” Color Interline-Transfer CCD
816(H) x 494(V) 798(H) x 584(V)
771(H) x 492(V) 753(H) x 582(V)
2:1 Interlace
0.5Lux / F1.2 (30IRE)
480 TV Line
VBS ; 1Vp-p, 75Ωunbalanced
15.734KHz(H) / 60Hz(V) 15.625KHz(H) / 50Hz(V)
Built in
ATW / AWC Selectable
ON / OFF Selectable
High / Normal Selectable
ON / OFF Selectable (ON: 1/100sec) ON / OFF Selectable (ON: 1/120sec)
more than 48dB (weight ON)
-10˚C ~ +50˚C [14˚F~122˚F] / 30% ~ 90%RH
62(W) x 58(H) x 165(D)mm
300g 290g 300g 290g
* Design and specifications are subject to change without notice
DECLARATION OF CONFORMITY
Application of Council Directive(s) 89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment CCTV Camera
Model Name SOC-4020Series
Beginning Serial NO. S3900001
Year of Manufacture 2003. 9. 1
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms
totheaboveDirective(s).
Manufacturer SAMSUNGTECHWINCO.,LTD
LegalRepresentativeinEurope
Signature Signature
FullName YOUNGTAEKSON FullName
Position QUALITYCONTROLMANAGER Position
Place CHANGWON,KOREA Place
Date 2003.9.1 Date
Blank : X2.5 vari-focal, f=3.8~9.5, F=1:1.3~2.0
W Series : X2.4 vari-focal, f=2.5~6.0, F=1:1.3~2.0
(DC Iris Lens adjustable)