Samsung MM-L2 User manual

MICRO COMPONENT
SYSTEM
CD-R/RW PLAYBACK
MM-L2
Instruction Manual

Safety Warnings
GB
2
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product.
Use of controls adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTER LOCKS DEFEATED, AVOID EXPOSURE TO
BEAM.
This symbol indicates that dan-gerous voltage
constituting of a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and main-tenance instructions in the
owners manual accompanying this unit.
WARNING: To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER, NO USER
SERVICEABLE PARTS INSIDE, REFER SER-
VICING TO QUALIFIED SERVICE
PERSONNEL.
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION
Wiring the Mains Power Supply Plug(UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of
the plug and, if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover omitted. If the cover is detachable. If a replacement fuse cover is required, it must be of the same colour
as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a
suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do NOT connect the plug to a
mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:–
BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured
BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY
THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1

GB
3
Contents
INSTALLING YOUR MICRO COMPONENT SYSTEM
Safety Warnings .......................................................................................................... 2
Front Panel View ......................................................................................................... 4
Rear Panel View .......................................................................................................... 4
Remote Control ........................................................................................................... 5
Connecting the Loudspeakers .................................................................................... 6
Inserting the Batteries in the Remote Control ............................................................. 6
Connecting Your System to the Power Supply ........................................................... 6
Connecting the AM(MW)/LW Aerial ............................................................................. 7
Connecting the FM Aerial ............................................................................................ 7
Setting the Clock ......................................................................................................... 8
CD PLAYER
Listening to a Compact Disc ....................................................................................... 8~9
Precautions When Using Compact Discs ................................................................... 9
Shuffle Play Function .................................................................................................. 9
Repeat Funtion ............................................................................................................ 9
CD Repeat A B Function ......................................................................................... 9
Programming the Order of Playback ...........................................................................10
Checking and Changing Programmed Tracks ............................................................10
TUNER
Searching for and Storing the Radio Stations .............................................................10
Selecting a Stored Radio Station ................................................................................11
Improving Radio Reception .........................................................................................11
TAPE DECK
Listening to a Cassette ................................................................................................11
Maintaining the Sound Quality ....................................................................................11
Recording a Radio Programme ...................................................................................12
Recording a CD ..........................................................................................................12
Recommendations for Recording ................................................................................12
Function to skip through 10 tracks at a time ...............................................................12
OTHER FEATURES
Timer Function .............................................................................................................13
Cancelling the Timer ...................................................................................................13
Sleep Timer .................................................................................................................14
Mute Function ..............................................................................................................14
Bass Amplification System (Super Bass) ....................................................................14
Equalizer.......................................................................................................................14
Microphone Function (option) .....................................................................................15
Connecting Headphones .............................................................................................15
Connecting to an External Source ..............................................................................15
Technical Specifications...............................................................................................16

GB
4
Front Panel View
Rear Panel View
On/Standby
Volume
CD Repeat
A B
Band
Tuning Mode Up
Down
Timer
Clock
Mute
EQ
S.Bass
TUNER
TAPE AUX
CD
Push Open
On/Standby button
CD Repeat (A B) button
TUNER/Band
TAPE button
Timer/Clock button
Mute button
Skip Down/Up buttons
Fast-Rewind button
Playbak button
Record button
CD Push Open button
CD button
Volume button
AUX button
Equalizer Preset button
Super Bass button
Fast-forward button
Stop/Eject button
Pause button
MIC JACK CONNECTOR(OPTIONAL)
HEAD PHONES JACK CONNECTOR
AM AERIAL CONNECTOR TERMINALS
FM AERIAL COAXIAL CONNECTOR
TERMINALS
AUX INPUT
LOUDSPEAKERS CONNECTOR
TERMINALS

GB
5
Remote Control
CD
CDCD
VOL.
VOL.
Tuning
Mode
On/Standby Timer
on/off
EQ Preset S.Bass Mute
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
Function
Timer
Clock
On/Standby button
Super Bass button
Equalizer Mode selection button
Sleep button
Program/Set button
CD Repeat button
CD Repeat A B button
Stop button
CD Track or radio
station search button
Timer/Clock Setting button
Timer setting/
Timer on/off button
Function selection button
Sound cut-off button
Tuner band selection button
Mono/Stereo button
+10(CD) button
Shuffle button
Play and pause button
Volume increase button
Tuning Mode button
Volume decrease button

GB
6
The loudspeaker connector terminals are located on the rear of both
the system and the loudspeakers (red and black tabs in both cases).
There are four terminals:
Two for the left speaker (marked L on the system)
Two for the right speaker (marked R on the system)
To achieve the correct sound quality, connect the:
Red cable to the + terminal
Black cable to the
- terminal
1To connect a cable to a terminal, push the tab as far as it will go:
To the left on the system
2Insert the cable up to the plastic sheathing, in the opening.
3Release the tab.
To the left on the system, until it clicks into place
Result: The cable is pinched and held firmly in place.
4Repeat the operation for each end of the cables.
Connecting the Loudspeakers Connecting Your System to the Power Supply
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when you:
Purchase the micro component system
Find that the remote control is no longer operating
correctly
1Place your thumb on the position marked on the battery
compartment cover (rear of the remote control) and push the
cover in the direction of the arrow.
2Insert two AAA, LR03 or equivalent batteries, taking care to
respect the polarities:
+ on the battery against + on the remote control
- on the battery against - on the remote control
3Replace the cover by sliding it back until it clicks into position.
When replacing the batteries, use a new set.
To achieve optimum performance, make sure
that the batteries are of the same type.
The power cord lead must be plugged into an appropriate socket.
Before plugging your system into an outlet, you must check
the voltage setting (OPTIONAL). If the voltage of the socket
does not correspond to the setting on the rear of the unit,
you may seriously damage your system.
1Check the position of the voltage selector on the bottom of the
system (OPTIONAL).
2Plug the power cord (marked AC CORD on the rear of the
system) into an appropriate socket.
3Press the On/Standby button to switch your Micro component
system on.
(Bottom)
(Rear)
RL

GB
7
Connecting the AM(MW)/LW Aerial
The AM(MW)/LW aerial (for long and middle waves) can be:
Placed on a stable surface
Fixed to the wall (you must first remove the base)
The AM aerial connector terminals are located on the rear of the
system and are marked AM ANT.
To avoid noise interference, check that the
loudspeaker wires do not run close to the aerial
wires. Always keep them at least 2 inches (5 cm)
away.
Connecting the FM Aerial
There are two types of aerials, follow the instructions below
(depending on option chosen).
How to connect a SCREW TYPE wire aerial.
The FM aerial connector terminals are located on the rear of the
system and marked FM(75Ω).
Spread the T.form FM aerial out and attach the ends to a wall,
in the position providing the best reception.
How to connect a COAXIAL TYPE areial (optional).
Connect a 75Ωantenna to the FM aerial terminal.
Plug the connector on the FM aerial supplied into the coaxial
socket (75Ω) marked FM on the rear of the system.
Follow the instructions given on Page 8 to tune into a radio
station, and determine the best position for the aerial.
If reception is poor, you may need to install an outdoor aerial.
To do so, connect an outdoor FM aerial to the FM socket on the
rear of the system, using a 75Ωcoaxial cable (not supplied).
FM FM
FM AERIAL
(supplied)
75ΩCOAXIAL CABLE
(not supplied)
On/Standby
Volume
CDRepeat
AB
Band
TuningMode Up
Down
Timer
Clock
Mute
EQ
S.Bass
TUNER
TAPE AUX
CD

Your system is equipped with a clock which allows you to turn
your system on and off automatically. You should set the clock:
When you purchase the Micro component system
After a power failure
After unplugging the unit
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1Switch the system on by pressing On/Standby.
2Press Timer/Clock twice.
Result: CLOCK is displayed.
3Press Program/Set.
Result: The hour flashes.
4To... Press...
Increase the hours
Decrease the hours
5When the correct hour is displayed, press Program/Set.
Result: The minutes flash.
6To... Press...
Increase the minutes
Decrease the minutes
7When the correct time is displayed, press Program/Set.
Result: The clock starts and is displayed, even when the
system is in standby mode.
You can display the time, even when you are using another
function, by pressing Clock once.
This unit has been designed to playback the CDs: Audio CD, CD
Text, CD-R and CD-RW.
When you have loaded at least one compact disc into the
player, you can start listening to it.
Continued use of irregular shape CDs (heart-shape, octagonal,
etc.) can damage the unit.
1Select the CD function by pressing CD on the front panel.
2Open the compact disc compartment by pressing down and
releasing the cover.
3Place your disc in the compartment, with the label on the disc
facing upwards.
4Close the compartment by pushing down on the cover until it
clicks into place.
Result: The display indicates the number of tracks on the
disc.
5Press the PLAY/PAUSE ( ) button.
Result: The first track on the disc plays and the track
number is displayed.
6To stop playback temporarily, press the PLAY/PAUSE ()
button. Press PLAY/PAUSE ( ) again to continue playing
the disc.
7To start playing Press...
at the beginning of...
The next track SKIP/SEARCH once
The current track SKIP/SEARCH once
The previous track SKIP/SEARCH twice
The track of your choice SKIP/SEARCH or
the appropriate number of times
8To search through Press and hold down...
the tracks...
Forwards SKIP/SEARCH until you
reach the required point
Backwards SKIP/SEARCH until you
reach the required point
You are advised to turn the volume down before using
this function.
9Press the STOP ( ) button when you have finished.
GB
8
CD
CDCD
VOLl.
VOL.
Tuning
Mode
CD CD
Setting the Clock
CDCD
VOLl.
VOL.
Tuning
Mode
On/Standby
Timer
on/off
EQ Preset S.Bass Mute
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
Function
Timer
Clock
CD CD
2
1
74
46 6
35
Listening to a Compact Disc
On/Standby
24
Band
Tuning Mode Up
Down
Timer
Clock
Mute
EQ
S.Bass
TUNER
TAPE AUX
CD
1 5 6
956
78
78
When playing a CD-R or CD-RW
User-edited CD-Rs (Recordable) and CD-RWs (Rewritable) can be
played back only if they are already “finalized”.
You can play back your original CD-Rs or CD-RWs recorded in
music CD format. (However, they may not be played back
depending on their characteristics or recording conditions.)
Some CD-Rs or CD-RWs may not be played back on this unit
because of their disc characteristics, damage or stain on them,
or if the player’s lens is dirty.
CD-RWs may require a longer readout time. (This is caused by
the fact that the reflectance of CD-RWs is lower than for
regular CDs.)
CD
9

GB
9
To guarantee hours of enjoyable listening with your compact
discs:
Always hold them by the edges to avoid leaving
fingerprints on the shiny surface
Always replace them in their cases after listening to
them
Do not fix paper or adhesive tape to the discs and do
not write on the label
Clean the player with a special cleaning disc
You can listen to the tracks on a compact disc in a different order
each time, as the various tracks will be selected automatically in a
random sequence.
1Press the Shuffle button.
Result: The Shuffle indication appears and all the tracks
are played in a random order. Both the track
number and the playing time are displayed.
2When playing tracks in a random order, you can:
Move on to the next track (selected at random) by
pressing / .
Search quickly for a specific point in the current track by
pressing /.
3 When you have finished the random playback, press or
press the Shuffle button again.
You can repeat:
A specific track on a compact disc
All tracks on the compact disc
This function is not available in the CD STOP mode.
1Press the Repeat button.
To repeat the... Press Repeat...
Current track indefinitely Once (REPEAT 1 is displayed)
Disc Twice (REPEAT ALL is displayed)
2When you wish to stop the Repeat function, press Repeat
once more.
Result:REPEAT is no longer displayed.
When you select CD Repeat A B playback, the music
passages to which you were listening is repeated five times.
1Press PLAY/PAUSE button.
Result: The CD player starts playing.
2Press CD Repeat A B button.
Result: The indications appear: START.
The flashes appear: AB
A Time is memorized.
3Press CD Repeat A B button.
Result: The indications appear: END.
B Time is memorized.
Your selected passages are repeated five times.
4When you have finished the Repeat playback,
Press CD Repeat A B.
Precautions When Using Compact Discs
Shuffle Play Function
Repeat Function
CD Repeat A B Function
CD
VOLl.
Repeat
CD A B
+10 CD Repeat Shuffle
Band
CD
CDCD
VOLl.
VOL.
Tuning
Mode
Repeat
CD A B
+10 CD Repeat Shuffle
CD CD
2
2
3
13
AB
34
2
1
CD
VOLl.
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
CD
2
1

GB
10
You can decide for yourself:
The order in which you listen to the tracks
The tracks to which you do not wish to listen
This feature can be combined with the Repeat function.
1If necessary, stop the player by pressing STOP ().
2Press Program/Set.
Result: PROGRAM and P - 01-- are displayed.
3Select the required track by pressing the SKIP buttons:
to move backwards through the tracks
to move forwards through the tracks
4Press Program/Set.
Result:P - 02 -- is displayed.
5To select other tracks, repeat Steps 3and 4.
You can programme up to 15 tracks.
6When you have finished selecting the tracks, press
PLAY/PAUSE ( ) to start listening to the selection, in the
order in which the tracks were programmed.
7Press STOP ( ) twice to cancel the selection when the disc is
playing.
You can check and change your selection of tracks at any time.
You must have selected at least one track.
1 Press STOP ( ) once if you have started listening to the selection.
2Press Program/Set.
Each time you press Program/Set, the next selection
is displayed.
3Press Program/Set one or more times until the track to be
changed is displayed.
4Press SKIP or to select the new track.
5Press Program/Set.
6Press PLAY/PAUSE ( ) to start listening to the selection.
Result: The first track selected is played.
You can change one or more tracks in your initial
selection.
You can store up to:
15 FM stations
8 MW stations (optional)
7 LW stations (optional) 15 AM stations (optional)
1 Switch the system on by pressing On/Standby.
2 Press TUNER to select the radio function
3 Select the required frequency band by pressing Band.
Result: The appropriate indication is displayed:
FM Frequency Modulation
MW Medium Wave or AM (Amplitude Modulation)
LW Long Wave
4 Select the station to be stored by pressing TUNING
and to increase or decrease the frequency respectively.
To search for a station Press the appropriate button...
Manually One or more times.
Result: The station changes each time
you press the button.
Automatically And hold it down for at least one seconds.
Result: The next station is found auto-
matically.
The automatic search function may stop on a frequency that
does not correspond to a radio station. If this happens, use the
manual search function.
Result:TUNED is displayed when a station is received.
5 Adjust the volume by pressing Vol. + and Vol. - .
6 If there is noise interference on an FM stereo station, press the
Mono/ST button once to select the mono mode. This may improve the
reception. Press the Mono/ST button again to return to the stereo
mode.
If a preset station is displayed when you are searching for a radio
station, press Tuning Mode to select the MANUAL mode and
continue searching.
7 If you do not want to store the radio station found, revert to Step 3to
search for another station.
Otherwise:
aPress Program/Set.
Result: The programme number and PROG are displayed
for a few seconds.
bPress TUNING and to assign a programme number
between 1 and 20 (for FM).
Result: The programme number is displayed. For the FM
frequency band, the over symbol is displayed to
indicate two-digit station numbers.
cPress Program/Set to store the radio station.
Result:PROG is no longer displayed and the station is
stored.
8 To store any other radio stations required, repeat Steps 3to 7.
This function can be used to assign a new station to an existing
programme number.
Programming the Order of Playback
Checking and Changing Programmed Tracks
Searching for and Storing the Radio Stations
CDCD
VOLl.
VOL.
Tuning
Mode
CD
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
CD CD
4
2
6
7
1
CDCD
VOLl.
VOL.
Tuning
Mode
CD
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
CD CD
35
2
6
1
3
3
4
4
CD
CDCD
VOLl.
VOL.
Tuning
Mode
On/Standby
Volume
CD Repeat
A B
Band
TUNER CD
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
P
rogram
/Set
TUNER
VOL.
VOL.
CD CD
3
2
3
2
1
6
7
5
5
44
PROG
PROG

GB
11
You can listen to a stored radio station as follows:
1Switch the system on by pressing On/Standby.
2Press TUNER to select the radio function.
3Select the required frequency band by pressing Band.
4Select the radio station as follows.
To listen to... Press...
A stored station aTuning Mode to select the
PRESET mode.
bTUNING and to select
the required station.
Another station TUNING and to increase or
decrease the frequency respectively
until the required station is found.
Press Tuning Mode again to exit the stored station
selection function.
You can improve the quality of radio reception by:
Rotating the FM or MW (AM), LW (optional) aerial
Testing the positions of the FM and MW (AM) , LW
(optional) aerials before fixing them to the wall
If reception from a specific FM radio station is poor, press
Mono/ST button to switch from stereo mode to mono. The
quality of the sound will be improved.
You can listen to any type of audio cassette with this player.
1Press the TAPE button to select the cassette function.
2Open the cassette deck by pressing the STOP/EJECT ()
button.
3Insert the pre-recorded cassette with the open edge of the tape
facing downwards.
4Close the deck by pushing on it until it clicks into place.
5Press the PLAY ( ) button.
Result: The cassette starts playing.
6To stop the playback temporarily, press the PAUSE ( II ) button.
Press the PAUSE (
II ) button to continue listening to the
cassette.
7When you have finished, press the STOP/EJECT ( ) button.
8To... Press the...
Rewind the cassette REW ( ) button
Fast-forward the cassette F.FWD ( ) button
Stop the player STOP/EJECT ( ) button
The rewind or fast-forward functions stop automatically
when the beginning or end of the cassette is reached.
9To open the deck, press the STOP/EJECT ( ) button.
To obtain the best possible results from your cassette player, you
must clean it regularly (heads, roller and drive capstan).
Open the deck by pressing the STOP/EJECT ( ) button. Use a
cotton bud and a special cassette cleaning agent to clean the:
Heads ( )
Roller ( )
Drive capstan ( )
To guarantee hours of enjoyable listening with your cassettes:
Check that the tape in the cassette is always sufficiently taut
Store your cassettes in a clean place, out of direct sunlight,
where they will not be exposed to high temperatures
Avoid using 120-minute cassettes as they are extremely fragile
Selecting a Stored Radio Station
Improving Radio Reception
Listening to a Cassette
Maintaining the Sound Quality
CD
EQ Preset S.Bass Mute
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
Function
Band
Tuning Mode Up
Down
r
k
TUNER
TAPE AUX
CD
TAPE
156
8
7
29
8 8
On/Standby Timer
on/off
EQ Preset S.Bass Mute
Sleep Mono/ST TUNER
Band
Program
/Set
Function
Timer
Clock
2
1
3
CD
CDCD
VOLl.
VOL.
Tuning
Mode
CD
Tuing
Mode
CD
44
4

GB
12
You can record a radio programme of your choice and listen to it
at a later date.
1Insert a blank cassette in the cassette deck.
2Press TUNER to select the radio function.
3Select the radio station that you wish to record.
4To start recording, press the RECORD ( ) button.
Result: Recording starts immediately.
5To stop recording temporarily, press the PAUSE ( II ) button.
6When you wish to stop recording, press the STOP/EJECT
( ) button.
You can record a compact disc on a cassette.
1Insert a blank cassette in the cassette deck.
2Press the CD button to select the CD function.
3Load the compact disc (see page 8).
4Press the RECORD ( ) button.
Result: The first track on the disc is played and the player
starts recording automatically
If you wish to record a specific track, select it before
pressing the RECORD ( ) button.
5If you wish to stop recording temporarily, press the PAUSE ( II )
button.
6When you have finished recording, press the STOP/EJECT
( ) button.
Record on normal bias cassettes only.
To prevent erasing a cassette that you wish to keep,
remove the safety tabs on the upper edge of the
cassette. To re-record a cassette, where the tabs have
been broken, simply cover the openings with
adhesive tape.
It is an infringement of copyright laws to copy
records and pre-recorded cassettes or to re-record
them in any form without the permission of the
owners of the corresponding copyright.
Recording a Radio Programme
Recording a CD
Recommendations for Recording
Tuning Mode Up
Down
Timer
Clock
Mute
EQ
S.Bass
TAPE AUX
TUNER
2
465
465
Band
Timer
Clock EQ
TUNER
TAPE AUX
CD
CD
2
Press the +10 button briefly while playing back a CD .
The track 10 tracks after the current one will then be
played back.
Example: If you want to select track 23 during playback of
track 5, press the +10 button two times, and then
press the button three times.
Function to skip through 10
tracks at a time
5 ➝ 10 ➝ 20 ➝ 21 ➝ 22 ➝ 23
CD CD CD
+10 +10

GB
13
The timer enables you to switch the system on or off at specific times.
Example: You wish to wake up to music every morning.
If you no longer want the system to be switched on or off
automatically, you must cancel the timer.
Before setting the timer, check that the current
time is correct.
For each step, you have a few seconds to set
the required options. If you exceed this time,
you must start again.
1Switch the system on by pressing On/Standby.
2Press Timer/Clock until TIMER is displayed.
3Press Program/Set.
Result: ON TIME is displayed for a few seconds, followed
by any switch-on time already set; you can set the
timer switch-on time.
4Set the timer switch-on time.
aSet the hour by pressing TUNING and .
bPress Program/Set.
Result: The minutes flash.
cSet the minutes by pressing TUNING and .
dPress Program/Set.
Result:OFF TIME is displayed for a few seconds,
followed by any switch-off time already set; you
can now set the timer switch-off time.
5Set the timer switch-off time.
aSet the hour by pressing TUNING and .
bPress Program/Set.
Result: The minutes flash.
cSet the minutes by pressing TUNING and .
dPress Program/Set.
Result:VOL XX is displayed, where XX corresponds to the
volume already set.
6Press TUNING and to adjust the volume level and
press Program/Set.
Result: The source to be selected is displayed.
7Press TUNING and to select the source to be played
when the system switches on.
If you select... You must also...
TAPE (cassette) Insert a recorded cassette in the
decks before setting the system to
standby.
TUNER (radio) aSelect the FM or AM frequency
band by pressing TUNING
and .
bPress Program/Set.
cSelect a preset station by pressing
TUNING and .
CD (compact disc) aLoad compact discs.
8Press On/Standby to set the system to standby mode.
Result: is displayed to the middle right of the time,
indicating that the timer has been set. The system will
switch on and off automatically at the required times.
If the timer switch on and off times are identical, the word
ERROR is displayed.
After having set the timer, it will start automatically as shown by
the indication on the display. If you no longer wish to use the
timer, you must cancel it.
You can stop the timer at any time (system on or in
standby mode).
To... Press Timer On/Off
Cancel the timer Once.
Result: is no longer displayed.
Restart the timer Twice.
Result: is displayed again.
Timer Function
On/Standby Timer
on/off
EQ Preset S.Bass Mute
Sleep Mono/ST TUNER
Band
Program
/Set
Function
Timer
Clock
CD
CDCD
VOLl.
VOL.
Tuning
Mode
On/Standby Timer
on/off
EQ Preset S.Bass Mute
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
Function
Timer
Clock
CD
CD
Cancelling the Timer
66 77 44 55
67435
2
18

GB
14
You can turn the sound off temporarily on your system.
Example: You wish to answer a telephone call.
1Press Mute on the remote control.
Result:MUTE is displayed and the sound is switched off.
2To switch the sound back on at the same volume as before,
press Mute again.
Your micro component system is equipped with a bass amplification
system called Super Bass. This function makes the sound more
powerful and true-to-life.
1Press S. Bass on the front panel.
Result: is displayed
2To cancel this function, press S. Bass again.
Your micro component system is equipped with a preset
equalizer that enables you to choose the most appropriate
balance between treble and bass frequencies, according to
the type of music to which you are listening.
Press the EQ Preset button one or more times until the required option
is selected.
To obtain a... Select...
Standard balance (linear) PASS
Balance suitable for classical music CLASSIC
Balance suitable for pop music POP
Balance suitable for rock music ROCK
Result: The corresponding indication is displayed.
Sleep Timer
Equalizer
Mute Function
Bass Amplification System (Super Bass)
EQ Preset S.Bass Mute
Sleep
Repeat
CD A B
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
Function
EQ Preset S.Bass Mute
Sleep Mono/ST TUNER
Band
Program
/Set
Function
On/Standby Timer
on/off
EQ Preset S.Bass Mute
Sleep
Repeat
+10 CD Repeat Shuffle
Mono/ST TUNER
Band
Program
/Set
Function
Timer
Clock
12
12
3
2
1
Band
Tuning Mode Up
Down
Timer
Clock
Mute
EQ
S.Bass
TUNER
TAPE AUX
CD
Tuning Mode Up
Down
Timer
Clock
Mute
EQ
S.Bass
TAPE AUX
12
90 MIN 60 MIN 45 MIN
OFF 15 MIN 30 MIN
You can set the system to switch off automatically.
Example: You wish to fall a sleep to music.
1Press Sleep.
Result: The following indications are displayed:
2Press Sleep one or more times to indicate how long the
system should continue playing before it switches off:
At any time, you can:
Check the remaining time by pressing Sleep
Change the remaining time by repeating Steps 1 and 2
3To cancel the sleep timer function, press Sleep one or more
times until OFF is displayed and the word SLEEP disappears.
SBS

The auxiliary input can be used to take advantage of the sound
quality of your micro component system when listening to other
sources.
Example: A television
A video disc player
A DAT or DCC cassette player
A Hi-Fi stereo video cassette recorder
To connect an external source, the source to be connected
must have an audio output. In addition, you must have an
RCA connection cable.
1Before connecting the external source, set the system to standby
mode and disconnect it and the external source from the mains.
2Connect the audio cable to the rear of the system.
Connect the... To the connector marked...
Red jack R(right)
White jack L(left)
For optimum sound quality, do not invert the right and left
channels.
3Press On/Standby switch it on.
4Press AUX.
Result:AUX is displayed.
5Switch the external source on.
6Adjust the volume and balance as required:
Volume
Equalizer
S. BASS
Example: You can watch a film and take advantage of stereo
sound as if you were at the cinema (provided that the
original sound track is in stereo).
GB
15
Connecting Headphones
Connecting to an External Source
On/Standby
Volume
CD Repeat
A B
Band
Tuning Mode Up
Down
Timer
Clock
Mute
EQ
S.Bass
TUNER
TAPE AUX
CD
AUX
3
4
You can connect a set of headphones to your micro component
system so that you can listen to music or radio programmes without
disturbing other people in the room. The headphones must have a 3.5
mm jack or appropriate adapter.
Connect the headphones to the Phones connector on the front panel
(or top right coner).
Result: The loudspeakers are no longer used for sound output .
Prolonged use of headphones at a high volume may
damage your hearing.
The microphone enables the user to mix in his or her vocals to
sing-along with the music.
Preparation
Plug the microphone with a 3.5mm mic jack into microphone terminal.
Microphone Function (option)

GB
16
Technical Specifications
SAMSUNG strives to improve its products at all times. Both the design specifications and these user instructions are thus subject to
change without notice.
TUNER
FM
Signal/noise ratio 55 dB
Usable sensitivity 15 dB
Total harmonic distortion 1 %
AM (MW)
Signal/noise ratio 40 dB
Usable sensitivity 56 dB
Total harmonic distortion 2%
LW (optional)
Signal/noise ratio 32 dB
Usable sensitivity 63 dB
Total harmonic distortion 2%
COMPACT DISC PLAYER
Frequency range 20 Hz - 20 KHz (±54 dB)
Signal/noise ratio 85 dB (at 1 KHz) with filter
Distortion 0.1% (at 1 KHz)
Channel separation 75 dB
Disc sizes Diameter: 120 or 80 mm. Thickness: 1.2 mm
TAPE DECK
Frequency range 125 Hz ~ 8 KHz
Signal/noise ratio 45 dB
Channel separation 33 dB
Erasing effect 40 dB
GENERAL
Output power 2 x 5 Watts (total hamonic distortion:10%)
Power supply AC mains: See the label
Dimensions 137(W)x225(H)x250(D)mm.

MEMO

ELECTRONICS
THIS APPLIANCE IS MANUFACTURED BY:
AH68-00954B