Samsung WS32Z46VSGXXEC User manual

COLOR TELEVISION RECEIVER
Chassis : K55A(P)
Model : WS32Z46VSGXXEC
WS32Z46VSGXXEU
COLOR TELEVISION RECEIVER CONTENTS
Precautions
Reference Information
Specifications
Alignment and Adjustments
Troubleshooting
Exploded Views and Parts List
Electrical Parts List
Block Diagrams
Schematic Diagrams
1.
2.
3.
4.
5.
6.
7.
8.
9.

Alignment and Adjustments
Samsung Electronics 4-1
4. Alignment and Adjustments
4-1 Adjustments
4-1-1 General Alignment Instructions
Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic
characteristics such as vertical size, horizontal size, and focus. Observe the picture and check for
good black and white details. There must be no objectionable color shading: If color shading is
present, demagnetize the receiver. If color shading persists, re-do purity and convergence adjustments.
Note :
1. This ‘4. Alignment and Adjustments’ applies to K55A chassis applications.
2. AC Power Supply: 160~300V or 100~240V, 50Hz
3. This service manual has been written on the basis of domestic remote-control model adopting K55A
chassis. Depending on sales location and product specifications, some of specifications herein may
be changed.
4-1-2 Focus Adjustment
K55A contains a dynamic focus circuit. When CRT PCB, FBT or CRT is replaced, be sure to adjust in the
following sequence:
Dynamic Focus Adjustment
1. Input a crosshatch pattern.
2. Select “Standard” from the menu,
3. Turn the Static Focus VR clockwise to set it to its maximum.
4. Turn the Dynamic Focus VR counterclockwise to set it to its
maximum.
5. Turn the Static Focus VR counterclockwise slowly for the clearest
center vertical line.
6. Turn the Dynamic Focus VR clockwise slowly for the clearest third line.
7. Check for the FOCUS of entire screen. If necessary, re-do adjustments 3~6.
After Adjustment
1
2
3

Alignment and Adjustments
4-2 Samsung Electronics
4-1-3 Screen Voltage Adjustment
1. Input a Toshiba pattern.
2. Use an oscilloscope to identify RK, BK, GK. And then adjust FBT Screen VR so that the voltage of
pedestal level doesn’t exceed 160V.
If a Toshiba pattern is not available, cancel the blue screen and input “No Signal” to AV IN so the voltage
of pedestal level doesn’t exceed 175V.
If an oscilloscope is not available, use a DC multi-meter in No Signal (black screen) to adjust RK, BK, GK
so that the highest voltage becomes 160Vp-p.
4-1-4 White Balance Adjustment
1. Warm up the TV set for at least 30 minutes.
2. Enter the Service Mode by pressing the remote control keys in the following sequence:
Power Off ➞Display ➞ Menu ➞Mute ➞Power On
3. Initialize all set data.
4. Input a Toshiba pattern.
5. Using a probe(CA100), do the White Balance adjustments.
(1) Adjust Low-Light.
- Adjust Sub Brightness to set Y.
- Adjust B Cutoff to set y.
- Adjust R Cutoff to set x.
(2) Adjust High-Light.
- Adjust Sub Contrast to set Y.
- Adjust B Drive to set y.
- Adjust R Drive to set x.
(3) Check the value of Low-Light. If necessary, readjust Low-Light.
(4) Check the value of High-Light. If necessary, readjust High-Light.15

Alignment and Adjustments
Samsung Electronics 4-3
4-1-5 When adjusting Screen Voltage and White Balance
1. Screen Voltage and White Balance are related each other. Make sure both adjustments are correct.
2. Adjust Screen Voltage before White Balance Adjustments. Make sure Screen Voltage is correct.
3. If White Balance has been readjusted, re-check Screen Voltage.
4. After adjustments are complete, check the following.
- If spots appear on the screen after pressing the Power On/Off key, readjust Screen Voltage.
- If flyback lines appear on the screen, readjust Screen Voltage.

ASSIGNMENT
RESET Control jack during E2PROM latch UP(Function:Low)SERIAL H
E2PROM only SDA LINE
E2PROM only SDA LINE
Automation and after-sales service related BUS STOP(STOP : LOW)
CXA2165 /CXA2151Q/VSP940X/BA7654F/MSP34XX/TUNER Control jack
CXA2165 /CXA2151Q/VSP940X/BA7654F/MSP34XX/TUNER Control jack
Reset when MSP34XX IC(SOUND PROCESS IC)has an error(Active : LOW)
Reset when VSP940X IC(1-chip IC)has an error
Analog GND
TTX and USA Caption Input source line(1V p-p)
Main AFT Control jack(0 ~ 3.3V)
MICOM “H-SYNC” Input, POSITIVE Input(3.3V p-p)
MICOM “V-SYNC” Input, POSITIVE Input(3.3V p-p)
OPEN
TV/VIDEO switching control jack
Function : LOW
Remote Control Input Jack
STAND BY : Hight, OFF : LOW
TIME ON : H TIME OFF : L
DEGAUSSIGN COIL CONTROL:Based on standard specifications
H : IN1, L : IN2(BA7657F) PIN(#16) Control jack
Reset active : HIGH
Crystal oscillation input jack
Alignment and Adjustments
4-4 Samsung Electronics
4-2 MICOM PORT
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
33
34
35
FUNCTION
W-PORT
ROM SDA
ROM SCL
BUS-STOP
MAIN SDA
MAIN SCL
S-RESET
V-RESET
VDD 2.5V
GND
VDD3.3V
CVBS IN
VDD2.5V
GND
AFT
SC1-ID
SC2-ID
KEY-1
H-SYNC
V-SYNC
KEY-3
KEY-2
X-RAY
IR-IN
STD-LED
TIM-LED
RELAY
SW1
GND
VDD 3.3V
RESET
X-IN
X-OUT
FIRST STATE
HIGH
SERIAL H
SERIAL H
HIGH
SERIAL H
SERIAL H
HIGH
HIGH
HIGH
HIGH
IV p-p
HIGH
HIGH
POSITIVE
POSITIVE
HIGH
HIGH
HIGH
HIGH
LOW
HIGH
HIGH
LOW
RANGE
TV MODE
0 ~ 2V
16 : 9 MODE
4.5 ~ 7V
4 : 3 MODE
9.5 ~ 12V
AV MODE
16 : 9 MODE
0 ~ 2V
MEMU
0~0.1V
VOL-
0.1~0.7V
VOL+
07~13V
CH-
1.3~1.9V
CH+
0.9~2.4V

Alignment and Adjustments
Samsung Electronics 4-5
ASSIGNMENT
OSD R-OUT Output jack (0.38V p-p), half tone : 0.9V p-p
OSD G-OUT Output jack (0.38V p-p), half tone : 0.9V p-p
OSD B-OUT Output jack (0.38V p-p), half tone : 0.9V p-p
OSD F/B-OUT Output jack (Clamped at STAND PULSE, Half Tone : LOW)
LOW : GNDHIGH : OPEN STATUS
Initially, these pins select an input source at LOW state
System (NTSC/PAL) MUST be separated
Active “LOW”
1080i control jack : 1080i (LOW), RF (Hight)
Magnetic field control
PIN
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
FUNCTION
GND
VDD 2.5V
OSD-R
OSD-G
OSD-B
CPRE
VDD 2.5V
GND
VDD 3.3V
PX, Y
PX, Y
SW3
SW2
S-MUTE
POWER
H,P-ID
TILT
FIRST STATE
HIGH
1.2V p-p
1.2V p-p
1.2V p-p
0.9V p-p
HIGH
HIGH
HIGH
HIGH
H
L
HIGH
F1
L
M
F0
M
L
fH
1.75KHz (480i/480P)
33.75KHz (1080i)

Alignment and Adjustments
4-6 Samsung Electronics
4-3 Factory Adjustment
4-3-1 Factory Adjustment values
SERVICE
Deflection
480P Offset
1080i Offset
Video Adjust1
Video Adjust2
Video Adjust3
Option
YC Delay
EEPROM
Reset
4-3-2 EUROPE & CIS Factory Data
ITEMS
V-AMP
V-SHIFT
H-EW
H-SHIFT
V-LIN(Fix)
UP-LIN(Fix)
LOW-LIN(Fix)
V-SC(Fix)
H-PAR
UP-COR
LOW-COR
H-TRA
BOW
ANGLE
V-POSI(Fix)
50
2.5
29” CIS
SDI CRT
33
28
26
0
9
9
4
3
38
25
31
18
33
28
35 -> 40
45
2
32” CIS
SDI CRT
33
28
32
0
9
9
3
1
38
25
31
18
33
28
40
50
2.5
34” CIS
TOS CRT
26
24
17
26
9
9
2
3
51
35
36
42
31
30
40
37
1.8
29” EUR
SDI CRT
33
28
26
0
9
9
4
3
38
25
31
18
33
28
35 -> 40
37
1.5
32” EUR
PHI CRT
41
26
36
21
11
9
1
0
19
33
33
43
33
28
40
H/L : 285/285 29” CIS, EU W/B COORDINATE
L/L : 285/285
REMARK
Vertical AMP adj(Gain Control)
Vertical Position adj(DC bias adj)
Horizontal AMP adj(Gain Control)
Horizontal Position adj(DC bias adj)
Vertical Linearity adj(Top/Bottom adj)
Vertical Linearity adj(Top adj)
Vertical Linearity adj(Bottom adj)
Vertical S correction adj
Horizontal pin distortion adj
Horizontal pin distortion up adj
Horizontal pin distortion low adj
Horizontal Tapezium distortion adj
Vertical line slope adj(parabola)
Vertical Linearity adj(sawtooth)
V-Position adj as to CRT inch
DEFLECTION : PAL

Alignment and Adjustments
Samsung Electronics 4-7
ITEMS
V-AMP
V-SHIFT
H-EW
H-SHIFT
V-LIN
UP-LIN
LOW-LIN
V-SC
H-PAR
UP-COR
LOW-COR
H-TRA
BOW
ANGLE
V-POSI
29” CIS
SDI CRT
-7
-4
5
30
-4
-1
3
0
8
7
3
7
-1
-1
0
32” CIS
SDI CRT
-7
-4
5
30
-4
-1
3
0
8
7
3
7
-1
-1
0
34” CIS
TOS CRT
-7
-4
5
30
-4
-1
3
0
8
7
3
7
-1
-1
0
29” EUR
SDI CRT
-7
-4
5
30
-4
-1
3
0
8
7
3
7
-1
-1
0
32” EUR
PHI CRT
0
-1
1
3
-4
-1
3
0
1
2
-1
0
0
0
0
REMARK
Vertical AMP adj(Gain Control)
Vertical Position adj(DC bias adj)
Horizontal AMP adj(Gain Control)
Horizontal Position adj(DC bias adj)
Vertical Linearity adj(Top/Bottom adj)
Vertical Linearity adj(Top adj)
Vertical Linearity adj(Bottom adj)
Vertical S correction adj
Horizontal pin distortion adj
Horizontal pin distortion up adj
Horizontal pin distortion low adj
Horizontal Tapezium distortion adj
Vertical line slope adj(parabola)
Vertical Linearity adj(sawtooth)
V-Position adj as to CRT inch
DEFLECTION : NTSC

Alignment and Adjustments
4-8 Samsung Electronics
ITEMS
R-Cutoff
G-Cutoff(Fix)
B-Cutoff
Color on/off
CR offset
CB offset
R-Drive
G-Drive(Fix)
B-Drive
Sub-Bright
Sub-Contrast
Sub-Color(Fix)
Sub-TInt(Fix)
CTI-Level(Fix)
COL AXIS(Fix)
LTI-Level(Fix)
VSU(Fix)
Merody Volume(Fix)
29” CIS
SDI CRT
41
25
28
1
32
32
37
32
32
32
7
15
28
1
1
1
2
7
32” CIS
SDI CRT
41
25
28
1
32
32
37
32
32
32
7
15
28
1
1
1
2
7
34” CIS
TOS CRT
46
32
18
1
32
32
46
32
26
40
7
10
28
1
1
1
2
7
29” EUR
SDI CRT
41
32
28
1
32
32
37
32
32
32
7
15
28
1
1
1
2
7
32” EUR
PHI CRT
41
32
38
1
32
32
40
32
38
47
7
15
28
1
1
1
2
7
REMARK
R-cutoff control adj
G-cutoff control adj
B-cutoff control adj
initial : “0” -> 1
DC-offset canceling adjust
DC-offset canceling adjust
R-Drive control adj
G-Drive control adj
B-Drive control adj
Sub-Bright control
Sub-Contrast control
color gain control(PAL SETTING AGAIN)
HUE control
Chrominance Transient Improvement
color detection axis setting(NTSC/USA)
Luminance Transient Improvement
vertical osd position
Volume gain control
Video Adjust 1

Alignment and Adjustments
Samsung Electronics 4-9
ITEMS
ABL Mode
Gamma
DPIC Level
DC Trans
ABL-TH
VM-Level
VM-Coring
VM-f0
VM-Limit
VM-Delay
SHP CD
SHP f0
SHP f1&p/o
AKB Time
Bandpass
Highpass
29” CIS
SDI CRT
3
2
3
3
14
1
2
2
2
3
1
0
8
13
17h
23h
32” CIS
SDI CRT
3
2
3
3
15
1
2
2
2
3
1
0
8
13
17h
23h
34” CIS
TOS CRT
3
2
3
3
14
1
2
2
2
3
1
0
8
13
17h
23h
29” EUR
SDI CRT
3
2
3
3
14
1
2
2
2
3
1
0
8
13
17h
23h
32” EUR
PHI CRT
3
2
3
3
14
1
2
2
2
3
1
0
8
13
17h
23h
REMARK
Rpicture/bright ABL gain control
RGB output correction control
Dynamic picture black expansion control
Y-System DC transmission ratio
Threshold voltage adj ABL-IN
VM-OUT Level control
VM-OUT coring control
VM-f0 control
VM-Limit level control
VM-OUT phase control(reference to R-OUT)
Sharpness gain control(color satuation)
Sharpness f0 control (3Mhz)
Sharpness gain control(PAL SETTING AGAIN)
AKB Bch reference pulse time control
VSP9407B Band pass filter
VSP9407B High pass filter
Video Adjust 2
ITEMS
H comp
V comp
PIN comp
AFC comp
sync phase
NR Value
29” CIS
SDI CRT
7
4
2
0
0
6
32” CIS
SDI CRT
8
5
2
0
0
6
34” CIS
TOS CRT
4
4
7
0
0
6
29” EUR
SDI CRT
7
4
7
0
0
6
32” EUR
PHI CRT
6
4
2
0
0
6
REMARK
H-EHT compensation setting(PAL SETTING AGAIN)
V-EHT compensation setting(PAL SETTING AGAIN)
PIN-EHT compensation setting(PAL SETTING AGAIN)
AFC-EHT compensation
WHEN USED 74HC123
PAL SETTING AGAIN
Video Adjust 3