Samsung WW60J3283 Assembly instructions

useful tips for your drum washing machine
✔ The descriptions and images in this document may differ from your actual
purchased product. For more information, refer to the user manual.
INSTALLING YOUR WASHING MACHINE
• Installing your washing machine in the location which is slippery
or uneven, will result in vibrations and noise.
• If there is too much noise or vibration, check whether the four
levelling adjustment legs are evenly and firmly on the floor.
• If the washing machine is not level, lift the washing machine
slightly and adjust the lowest of the four levelling adjustment legs.
✔ Before using your washing machine, you must remove the
shipping bolts from the back of the unit.
For more information on removing the safety devices, refer to the user manual.
LEVELLING YOUR WASHING MACHINE WITH THE LEVELLING FEET
✔ Refer to the descriptions appropriate to your washing machine.
1. Level your washer by turning the
adjustable nut in and out, as shown
in the figure.
2. When your washing machine is
level, tighten the locking nut using
the (-) driver.
1. Unfasten the locking
nut by turning it to the
left using a spanner.
2. Level your washing
machine by turning
the adjustable feet in
and out as necessary
by hand.
3. Fasten the locking
nut by turning it to the
right using a spanner.
CLEANING THE FILTER
Cleaning the water supply filter
✔ If the filter net is not installed, it may cause a water leakage and operating error. Make sure to install it.
1. Pull and remove the filter net. 2. Clean the filter. 3. Insert the filter net and fasten
its connector firmly.
Cleaning the debris filter
✔ When water does not drain well or ‘5E’ blinks on the display, clean the debris filter. The product appearance
may differ from your washing machine. (However, the cleaning descriptions are the same.)
1. Open the filter
cover using a coin
or a key.
4. Unscrew the
emergency drain
cap by turning it
counter clockwise.
2. Unscrew the
emergency drain
cap and pull out the
emergency drain
tube to drain off the
remaining water.
5. Clean the debris
filter and the inside
of the drain hose.
3. Hold the cap on
the end of the
emergency drain
tube and allow all
the water to flow
into a bowl.
6. Replace the
debris filter, the
emergency drain
cap and tube and
then close the filter
cover.
✔ If you open the debris filter when water remains inside the tub, water may flow out.
✔ If the debris filter is assembled incorrectly or not installed, it may cause a water leakage or operating error.
Therefore make sure to assemble it correctly.
MAKE SURE YOU KNOW...
Adding the
laundry
• Adding laundry
➲ Press the Add laundry(Stop&Add) button and add the laundry when the Add
laundry lamp turns on.
• If you add the laundry during a spin cycle, it starts again with the initial set time
regardless of the remaining time.
Washing
bedding
• Wash bedding using only the Bedding course.
➲ You can wash acrylic, mixed spinning and woolen bedding.
➲ When washing general clothes, the washing machine may
not operate in the optimal status.
• Wash only one bedding item at a time regardless of size.
➲ Insert bedding rolled up into a ball.
The center of gravity is distributed evenly causing less
vibrations and noise.
✔ Do not wash electric blankets or carpets.
✔ When spinning blankets, cotton bedding, and woolen bedding,
too much noise and vibrations may occur and the wash cannot
be completed as spinning is not performed.
Locking nut
Adjustable nut
Spanner
(-) Driver
Nut
Adjustable feet
Spanner
Inside
Debris
filter
Wash
individually.
Make sure that the leveling feet
legs are level with the floor.
DC68-02209B_EN_DE_FR_ES_IT_PT_RU.indd 1 2008-03-19 ¿ÀÈÄ 3:03:50

TRY THE FOLLOWING...
When the door does
not open
The door does not open when the temperature inside your washing machine is
high or when the tub is filled with water.
• When the internal air temperature after a wash is higher than 70 °C or the water
temperature is more than 55 °C.
Wait until the internal temperature has dropped.
• When the tub is filled with water.
➲ Select Spin to drain the water. Then you will be able to open the door.
For some models, you can open door when “End” is displayed or the end
melody is played.
✔ If you open the door by force, it may result in damage to the product or safety
issues.
When selecting the
Dry function
For the Drying capacity, 1/3 of the wash capacity is reasonable. The maximum
drying rate is 95%.
• If you insert more than the maximum drying capacity specified in the user
manual, the drying performance may decrease.
Remove and shake out the laundry. Heat and moisture is removed and the
laundry will be dry.
When inserting
fabric softener
If fabric softener is inserted above the reference line (MAX) of the
fabric softener compartment, fabric softener may enter directly
into the tub.
• Insert fabric softener only up to the reference line (MAX) so
that it does not overflow.
If the rinse cap (hereafter cap) is not inserted correctly or there
is foreign material in the cap when using concentrated fabric
softener (liquid fabric softener of a high viscosity), fabric softener
or water may remain.
• Check whether the cap is correctly inserted into the detergent
compartment where the fabric softener is inserted.
• Open the detergent compartment and press the removal
button inside. Remove and clean it.
When the wash time
increases
The wash time may increase if an unbalance is detected with the load, the
machine will automatically try to balance the load. This process may extend
the wash program time.
• Press the Start/Pause button and then check the laundry status. Spread the
laundry evenly and perform the course again.
SELF-TEST
✔ If any error message other than the following error messages is displayed, refer to the user manual.
Indication Symptom Action
When the door is
opened
Is the door opened?
➲ Make sure to operate your washing machine after closing the
door.
When no water is
supplied
Is the tap closed?
➲ Turn on the tap.
Is the filter net of the water supply hose connector blocked?
➲ Remove and clean the filter net of the water supply hose.
When the water does
not drain
Is the drain filter blocked?
➲ Clean the drain filter.
Is the washing machine frozen because of the cold weather?
➲ Add hot water into the tub and let it defrost for about one hour.
When the internal
temperature of the
drum is high
Did the washing machine pause while drying or performing an air
wash?
➲ The cooling fan operates automatically. Therefore wait until the
‘Hot’ indication disappears.
✔ Only the Power and Start/Pause buttons operate while the ‘Hot’
indication displays.
✔ When the internal temperature of the drum is high, the door
does not open. If you open the door by force, it may result in
product damage and safety issues. Therefore wait until the
temperature has dropped.
When water does not
drain because the
internal temperature
does not drop below
55 °C even if thirty
minutes has passed
after the wash has
finished
Have the cold and hot water supply hoses been mixed up?
➲ Connect the cold and hot water supply hoses correctly.
✔ Operate your washing machine again by pressing the Start/
Pause button.
Rinse
cap
MAX
DC68-02209B_EN_DE_FR_ES_IT_PT_RU.indd 2 2008-03-19 ¿ÀÈÄ 3:03:51