Samyung N560 User manual

S
Sa am my yu un ng g N N5 56 60 0 / / N NF F5 56 60 0

Installation and Operation Manual
2

Installation and Operation Manual
3
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
FCC Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a normal installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1- Reorient or relocate the receiving antenna
2- Increase the separation between the equipment and receiver
3- Connect the equipment into an output on a circuit different from that to which the
receiver is connected
4- Consult the dealer or an experienced technician for help
5- A shielded cable must be used when connecting a peripheral to the serial ports
Important
It is the owner‟s sole responsibility to install and use the unit in a manner that will not cause
accidents, personal injury or property damage. The user of this product is solely responsible for
observing safe boating practices.
Global Positioning System: The Global Positioning System (GPS) is operated by the US
government which is solely responsible for its operation, accuracy and maintenance. The GPS
system is subject to changes which could affect the accuracy and performance of all GPS
equipment anywhere in the world.
Installation: If installation is not correct, the unit can not perform at its designed potential. If in
doubt, consult your Samyung ENC dealer. Ensure that any holes made are in a safe position and
will not weaken the boat‟s structure. If in doubt, consult a qualified boat builder.
SAMYUNG ENC DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY
CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW.
Governing language: This statement, any instruction manuals, user guides and other
information relating to the product (documentation) may be translated to, or has been translated
from, another language (translation). In the event of any conflict between any translations of the
documentation, the English language version of the documentation will be the official version of
the documentation. This manual represents the installation procedures as at the time of printing.
Samyung ENC reserves the right to make changes to specifications without notice.
Copyright © 2009 Samyung ENC, Republic of Korea, all rights reserved.
Presentation
Thank you for having purchased a Samyung ENC product. This handbook contains an explanation
of how to install, operate and maintain your unit.

Installation and Operation Manual
4
SAFETY INSTRUCTIONS
Electronic charts displayed by the chart plotter are believed to be
accurate and reliable, but they are not intended to replace official
charts which should remain your main reference for all the matters
related to the execution of a safe navigation. For this reason we would like to
remind you that you are required to carry on board and use the officially published
and approved nautical chart.
Please read through this manual before the first operation. If you have any
questions, please contact the customer service or your local dealer or distributor
Extensive exposure to heat may result in damage to the chart plotter.
Connection to the power source with reversed polarity will damage the chart
plotter severely. This damage is not covered by the warranty.
Do not disassemble. The chart plotter contains dangerous high voltage circuits
which only experienced technicians must handle
Exposure of the display to UV rays may shorten the life of the liquid crystals used
in you plotter. This limitation is due to the current technology of the LCD display.
Avoid overheating which may cause loss of contrast and, in extreme case, a
darkening of the screen. Problems which occur from over heating are reversible
when temperature decreases.
Screen Cleaning Precautions
Cleaning your chart plotter screen is a very important operation and must be done
carefully. The following is the cleaning procedure.
You use a tissue or lens tissue and a cleaning spray containing Isopropanol (a
normal spray cleaner sold for PC screens. Fold the tissue or lens tissue into a
triangular shape, moisten the tip and use the index finger behind a corner to
move the tissue across the surface, in overlapping side to side strokes. If the
tissue is too wet, a noticeable wet film will be left in its path and you will need to
repeat the process. If too dry, the tissue won‟t glide easily, and may damage the
surface.
If you require technical advice or assistance, contact your nearest Samyung ENC
office or visit our website, www.samyungenc.com.

Installation and Operation Manual
5
1 Introduction
1-1 General Information................................................................9
1-2 Specification...........................................................................9
1-3 Packing List .......................................................................... 11
1-4 Optional Accessories ............................................................. 11
2 Getting Started
2-1 Mounting the Unit ................................................................. 12
2-1-1 Bracket Mounting...............................................................................12
2-1-2 Flush Mounting ..................................................................................12
2-2 Keys .................................................................................... 13
2-3 C-MAP MAX Secure Digital (SD) Card ...................................... 14
2-4 Chart Selection ..................................................................... 14
2-5 Simulate Mode...................................................................... 14
2-6 Data Bar .............................................................................. 15
2-7 Compass.............................................................................. 16
2-8 Multi window displays ........................................................... 17
2-9 Man overboard (MOB)........................................................... 19
3 General Operation
3-1 Manual / Auto Power on and off............................................. 20
3-2 Brightness, night mode and Background ................................. 20
3-3 The page window ................................................................. 21
3-4 Chart ............................................................................ 23
3-4-1 Chart window ....................................................................................23
3-4-2 Perspective view ................................................................................23
3-4-3 Latitude and longitude........................................................................24
3-4-4 Chart scale ........................................................................................24
3-4-5 Finding a chart symbol .......................................................................24
3-4-6 S-Map search ....................................................................................25
3-4-7 Chart symbols and information ............................................................25
3-4-8 Introduction to navigating...................................................................25
3-4-9 Going to a waypoint or to a point on the chart ......................................26
3-4-10 Following a route .............................................................................26
3-4-11 Goto Key .........................................................................................26
3-4-12 Distance and bearing calculator .........................................................27
3-4-13 Projected course ..............................................................................27
3-5 Sonar ........................................................................... 28
3-5-1 Interpreting the display ......................................................................28
3-5-2 Mode ................................................................................................28
3-5-3 Single and Dual frequency fish finding .................................................29
3-5-4 Range...............................................................................................29
3-5-5 Gain .................................................................................................30
3-5-6 Sonar window display.........................................................................31

Installation and Operation Manual
6
3-5-7 No split .............................................................................................31
3-5-8 Split zoom and Full Screen zoom .........................................................32
3-5-9 Split bottom ......................................................................................32
3-5-10 Split 50/200.....................................................................................33
3-5-11 Split A-Scope ...................................................................................33
3-6 Highway ....................................................................... 34
3-7 Gauges ........................................................................ 34
3-8 Waypoints..................................................................... 35
3-8-1 Creating a new waypoint ....................................................................35
3-8-2 Moving a waypoint .............................................................................35
3-8-3 Editing an existing waypoint................................................................35
3-8-4 Deleting a waypoint ...........................................................................36
3-8-5 Find a waypoint .................................................................................36
3-8-6 Sort Waypoints ..................................................................................36
3-8-7 Deleting all waypoints ........................................................................36
3-9 Routes.......................................................................... 37
3-9-1 Managing a route from the chart window .............................................37
3-9-2 Managing a route from the route window .............................................38
3-10 Satellites ..................................................................... 39
3-10-1 Satellite information .........................................................................39
3-11 Tides........................................................................... 40
3-12 AIS ............................................................................. 41
3-12-1 Viewing AIS Vessels..........................................................................41
3-12-2 AIS Windows ...................................................................................41
3-13 DSC .......................................................................... 43
3-13-1 distress ...........................................................................................43
3-13-2 Poll .................................................................................................44
3-14 NAVTEX..................................................................... 45
3-15 Engine Faults.............................................................. 45
4 Advance Settings
4-1 System Configuration Settings ........................................ 46
4-1-1 Language ..........................................................................................46
4-1-2 Chart Selection ..................................................................................46
4-1-3 Beep volume .....................................................................................46
4-1-4 Auto power .......................................................................................46
4-1-5 Features............................................................................................46
4-1-6 Factory reset .....................................................................................46
4-1-7 About ...............................................................................................46
4-2 Chart Settings................................................................ 47
4-2-1 Rotation............................................................................................47
4-2-2 Palette ..............................................................................................47
4-2-3-1 General(C-MAP) ..............................................................................47
4-2-3-2 General(S-MAP) ..............................................................................48
4-2-4-1 Land & Sea (C-MAP)........................................................................48

Installation and Operation Manual
7
4-2-4-2 Land & Sea (S-MAP)........................................................................48
4-2-5 Map datum........................................................................................48
4-2-6 NMEA datum offset ............................................................................49
4-2-7 Map shift...........................................................................................49
4-2-8 Restore default ..................................................................................49
4-3 Sonar Settings .............................................................. 50
4-3-1 Frequency .........................................................................................50
4-3-2 Palette ..............................................................................................50
4-3-3 Scroll speed.......................................................................................50
4-3-4 Digit size ...........................................................................................50
4-3-5 Fish ..................................................................................................50
4-3-6 Advance Settings ...............................................................................50
4-3-7 Restore default ..................................................................................50
4-4 GPS Settings ................................................................. 51
4-4-1 GPS Source .......................................................................................51
4-4-2 DGPS Source .....................................................................................51
4-4-3 Static Navigation................................................................................51
4-4-4 Speed Filter and Course Filter .............................................................51
4-4-5 Lat/Lon d.p‟s .....................................................................................51
4-4-6 Ship speed ........................................................................................51
4-4-7 Magnetic Variation .............................................................................51
4-5 Track & Log Settings...................................................... 52
4-5-1 Track ................................................................................................52
4-5-2 Logs .................................................................................................52
4-6 Memory Settings ........................................................... 53
4-6-1 Save .................................................................................................53
4-6-2 Load .................................................................................................53
4-6-3 Delete...............................................................................................53
4-6-4 Format..............................................................................................54
4-6-5 Screen snap shot ...............................................................................54
4-7 AIS Settings .................................................................. 54
4-7-1 Display filter ......................................................................................54
4-7-2 Alarm option......................................................................................55
4-7-3 Display options ..................................................................................55
4-7-4 Restore default ..................................................................................55
4-8 Alarms......................................................................... 56
4-8-1 Fish ..................................................................................................56
4-8-2 Deep ................................................................................................56
4-8-3 Shallow.............................................................................................56
4-8-4 Temperature......................................................................................56
4-8-5 Temperature rate ...............................................................................56
4-8-6 Low battery.......................................................................................56
4-8-7 Navigation alarms ..............................................................................56
4-8-8 AIS...................................................................................................56
4-8-9 DGPS................................................................................................56
4-8-10 Restore default ................................................................................56
4-9 Others.......................................................................... 57
4-9-1 Simulate ...........................................................................................57
4-9-2 Waypoint ..........................................................................................57
4-9-3 GPS ..................................................................................................57

Installation and Operation Manual
8
4-9-4 Units.................................................................................................57
4-9-5 Comms .............................................................................................57
4-9-6 Calibrate ...........................................................................................57
4-9-7 Time.................................................................................................57
4-9-8 Restore default ..................................................................................57
4-9-9 Calendar ...........................................................................................57
5 INSTALLATION
5-1 Options and Accessories ........................................................ 58
5-2 Connections ......................................................................... 59
5-3 Power/data cable.................................................................. 59
5-4 Alarm .................................................................................. 60
5-5 GPS antenna ........................................................................ 61
5-5-1 Internal antenna ................................................................................61
5-5-2 External antenna ...............................................................................61
5-5-3 The antenna using NMEA....................................................................61
5-6 NMEA 0183 .......................................................................... 62
5-7 NMEA 2000 .......................................................................... 63
5-8 Sonar Transducers ................................................................ 64
5-9 Setup and test...................................................................... 65

Installation and Operation Manual
9
1-1 General Information
The chart plotter is a precision-crafted GPS
chart Plotter with high-performance receiver
for the Global Positioning System
constellation of satellites, providing precise
location data with a host of navigation
features. Some functions require optional
units and sensors installed on your boat.
The chart plotter can be connected to
external devices with NMEA0183 and
NMEA2000 interface and display information.
Following are the examples.
•NAVTEX
•AIS receiver
•DSC VHF radio
•Transducer & sensors
•Autopilot
1-2 Specification
[N560]
GENERAL
Category
Detail
Size
164 mm(H) x 183 mm(W) x 74 mm(D)
Display
5.6” diagonal, TFT color, 480 x 640 pixels.
Supply voltage
10 to 34 V DC
Supply current
13.8 V
350 mA min - no backlighting.
480 mA max - full backlighting.
External beeper or light
output
Switched to ground to sound alarm, 30V DC, 200 mA maxmum
Operating temperature
-10° to 50°C
ALARMS
User set:Arrival radius, anchor, XTE, danger, low battery, loss of DGPS fix, dangerous AIS vessels.
GPS NAVIGATION
Chart card
C-MAP™ SD Card (NT-MAX, NT+ or NT)
User card
SD Card
Waypoints
Up to 10,000, with default or user defined alphanumeric names up to
eight characters.
Routes
100 Routes, with up to 100 points each
Tracks
By time or distance, 10 track of 15,000 points
Chart datums
216 Chart datums, One user-defined map shift.
Chart scale
0.2 to 500 nm for chart (chart dependent) down to 0.005 nm in plotter
mode.
COMMUNICATIONS
NMEA
NMEA 0183 4800, 9600, 38400 baud, NMEA 2000
NMEA 0183 Inputs from
compatible instruments
DBK, DBS, DBT, DPT, GGA, GLL, GNS, GGA, GSV, HDG, HDT, MDA,
MTA, MTW, MWD, MWV, RMC, RPM, VHW, VTG, VWT, ZDA
NMEA 2000 Inputs from
compatible instruments
System date and time(PGN126992),Vessel
Heading(PGN127250),Engine parameters/Rapid Update(PGN127488),
Engine parameters/Dynamic(PGN127489),Trip
parameters/Engine(PGN127497),Engine
parameters/Static(PGN127498),Fluid level(PGN127505),Water
Speed(PGN128259),Water depth(PGN128267),Position/Rapid
Update(PGN129025),COG & SOG/Rapid Update(PGN129026),GNSS
Position Data(PGN129029),GNSS DOPs(PGN129539),GNSS Sats in
View(PGN129540),Wind Data(PGN130306),Environmental Parameter-
Water temp(PGN130310),Environmental Parameter(PGN130311)
NMEA 0183 Outputs, for
APA, APB, BWR, GGA, GLL, GSA, GSV, RMB, RMC, VTG, XTE, DBT,
1 Introduction

Installation and Operation Manual
10
compatible instruments
DPT, MTW, VHW, XDR
NMEA 2000 Outputs, for
compatible instruments
Water Speed(128259), Water depth(128267), XTE(129283), NAV.
data(129284), NAV. data(129285), COG & SOG(129026), GNSS
position(129029), Water temp.(130310)
[NF560]
GENERAL
Category
Detail
Size
164 mm(H) x 183 mm(W) x 74 mm(D)
Display
5.6” diagonal, TFT color, 480 x 640 pixels.
Supply voltage
10 to 34 V DC
Supply current
13.8 V
800mA min - no backlighting.
1000mA max - full backlighting.
External beeper or light
output
Switched to ground to sound alarm, 30V DC, 200 mA maxmum
Operating temperature
-10° to 50°C
ALARMS
User set:Arrival radius, anchor, XTE, danger, too shallow, too deep, fish, temperature, temperature rate,
low battery, loss of DGPS fix, dangerous AIS vessels.
GPS NAVIGATION
Chart card
C-MAP™ SD Card (NT-MAX, NT+ or NT)
User card
SD Card
Waypoints
Up to 10,000, with default or user defined alphanumeric names up to
eight characters.
Routes
100 Routes, with up to 100 points each
Tracks
By time or distance, 10 track of 15,000 points
Chart datums
216 Chart datums, One user-defined map shift.
Chart scale
0.2 to 500 nm for chart (chart dependent) down to 0.005 nm in plotter
mode.
COMMUNICATIONS
NMEA
NMEA 0183 4800, 9600, 38400 baud, NMEA 2000
NMEA 0183 Inputs from
compatible instruments
DBK, DBS, DBT, DPT, GGA, GLL, GNS, GGA, GSV, HDG, HDT, MDA,
MTA, MTW, MWD, MWV, RMC, RPM, VHW, VTG, VWT, ZDA
NMEA 2000 Inputs from
compatible instruments
System date and time(PGN126992),Vessel
Heading(PGN127250),Engine parameters/Rapid Update(PGN127488),
Engine parameters/Dynamic(PGN127489),Trip
parameters/Engine(PGN127497),Engine
parameters/Static(PGN127498),Fluid level(PGN127505),Water
Speed(PGN128259),Water depth(PGN128267),Position/Rapid
Update(PGN129025),COG & SOG/Rapid Update(PGN129026),GNSS
Position Data(PGN129029),GNSS DOPs(PGN129539),GNSS Sats in
View(PGN129540),Wind Data(PGN130306),Environmental Parameter-
Water temp(PGN130310),Environmental Parameter(PGN130311)
NMEA 0183 Outputs, for
compatible instruments
APA, APB, BWR, GGA, GLL, GSA, GSV, RMB, RMC, VTG, XTE, DBT,
DPT, MTW, VHW, XDR
NMEA 2000 Outputs, for
compatible instruments
Water Speed(128259), Water depth(128267), XTE(129283), NAV.
data(129284), NAV. data(129285), COG & SOG(129026), GNSS
position(129029), Water temp.(130310)
SONAR FISHFINDING
Depth range
0 m to 600 m
Sonar output
Power:Variable, up to 600 W RMS
Dual frequency:50 khz and 200 kHz
Temperature
Range 0° to 37.7°C (32°F to 99.9°F)
Resolution of 0.1° unit.
Speed (from paddlewheel
transducer)
1 to 96.6 kph (57.5 mph, 50 kn).

Installation and Operation Manual
11
1-3 Packing List
Item List
Part
number
Model
N560
NF560
Display
N560-E
Ο
Ο
Bracket
N560-DB
Ο
Ο
Display Cover
N560-CC
Ο
Ο
Power Cable
LTW-1750-8 (N560)
LTW-2000-8 (NF560)
Ο
Ο
Bracket mounting screw
N560-BP
Ο
Ο
Flush mount Kit (Including screw)
N560-TK
Ο
Ο
Protection Cover
N560-CB
Ο
Ο
User’s Manual(Eng)
N560-ME
Ο
Ο
CD-ROM(Multi-language)
N560-MCD
Ο
Ο
Quick Reference (Multi-language)
N560-QSG
Ο
Ο
Cable tie
N560-CK
Ο
Ο
P58 Transducer
P58
X
Ο
1-4 Optional Accessories
Model
Part number
Item List
GPS Antenna +
GPS Antenna Support
SAN-60-10
GPS antenna + BNC Plug
GPS antenna support
GPS antenna cable(10m)
GPS Antenna Stand type
Support
57745
GPS Antenna Stand type
Support
Y cable
NF560-YC
Y cable(see section 5-8)
B45 Transducer
B45
Option
P39 Transducer(NMEA 2000)
P39
Option(for only N560)

Installation and Operation Manual
12
2-1 Mounting the Unit
The chart plotter is supplied with bracket and flush mounting kit. You can choose a method of
installation according to your preference.
2-1-1 Bracket Mounting
Before installing ensure the area the bracket is mounted to is strong enough to support the
weight of the GPS chart plotter. After the location is found, attach the mounting base to the
area using the supplied hardware.
Mounting the display Unit:
1 Hold the display unit and find a groove
joint between the display unit and bracket.
2 Gently push the display unit into the
groove of bracket and turn the knob to
clockwise to lock
Removing the display unit:
1 Turn the unit off
2 Turn the knob to counter clockwise
3 Pull the display unit out.
Note
The chart plotter with internal GPS antenna is
designed to be bracket mounting and flush mounting.
However, if you flush mount inside of your boat, GPS
performance can be reduced.
2-1-2 Flush Mounting
1 Find a location for flush mounting.
2 Drill a hole in the area of the cutout area
for the blade of jig saw.
3 insert and cut out the area on the panel
using the jig saw
4 Drill four holes for mounting studs.
5 Install the mounting studs on the chart
plotter and insert them into the mounting
hole.
6 Attach the chart plotter to the mounting
location by attaching the supplied
hardware to the mounting studs.
Note
1 If you flush mount, you need the optional external
GPS antenna.
2 Before Drilling holes make sure there is enough
space to mount the chart plotter there is no
obstructions.
2 Getting Started

Installation and Operation Manual
13
2-2 Keys
ESC –Exit from menu and return to
previous menu or window. In chart
window, it places own ship at center.
PAGE –Show main windows and allow you to
setup displays as you like.
CURSOR –Moves the cursor on the display
screen. In sonar window, you can
review sonar history.
MENU –Access to setting menu - Show
available options of current window.
-,+ –zoom in and zoom out to multiple chart
level
GOTO - Start navigating to a destination
point such as a MOB waypoint,
waypoint.
POWER –Turns power on/off. Opens display
Brightness, Night mode and
background settings.
SD Card –Open the cover to install
SD card
MOB –Places a MOB waypoint on the chart
window under the boats position.
WPT –Create a waypoint.
ENT –Select the desired option or to
confirm selection
-,+ –zoom in and zoom out to multiple chart
level
FUNC –Screen snap shot

Installation and Operation Manual
14
2-3 C-MAP MAX Secure Digital (SD) Card
This section provides instructions for inserting and removing C-MAP MAX SD card procedure.
Inserting the SD Card
1 Hold the SD card so that you can
see the C-Map label.
2 Open the door, gently push the SD card
into the slot; push the SD card in as far as
you hear click sound, then close door.
Removing the SD Card
1 Turn off the unit.
2 Open the door and push in on the SD card
until it is released.
3 Close the door.
Insert C-MAP SD card
correctly.
(DO NOT FORCE)
Close SD card door firmly all
the times.
Do not remove SD card
during reading and writing.
2-4 Chart Selection
A user can select a map between C-MAP and
S-MAP.
Chart Selection
1 Press and hold .
2 Select the system setting icon.
3 Select Chart then a chart you prefer.
S-MAP is a pre-
installed chart but
optional C-Map Max
can be used. Please
contact your nearest
Samyung ENC office
for purchasing the C-
Map
2-5 Simulate Mode
Simulate Mode is great for practicing the actual use of a product when the satellites signals
and internal alarms are not available. In the simulate mode, the unit turns the GPS receiver off
and ignores data from all optional devices.
Two simulate modes are available as below.
•Normal: Allows a user to practicing the
actual use of a product without satellites
connection.
•Demo: boat travel alone given route at
given speed and show different function of
the unit.
Do not try to navigate in a
simulate mode. While the
simulate mode is turned on,
the GPS receiver is not
active.

Installation and Operation Manual
15
2-6 Data Bar
Data bar displays useful navigation
information at the top of the display.
Displaying Data bar
1 Press and select Data bar.
2 Select Data bar.
Setting the data displayed in data bar
1 Press and select Data bar.
2 Select Data bar then Data bar setup.
3 Move the cursor key to highlight the data
field you want to change then press .
4 Select Data type.
5 Select a desired data you want to display in
the field then press .
6 Repeat above steps if necessary.
Selecting the Data bar size
1 Press and select Data bar.
2 Select Data bar then Data bar size.
3 Select the desired size of data bar.
[Large]
[Small]
Tip:If you select None for all data fields,
the data bar will disappear to save space for
the chart.
Tip: Even though you setup a data bar
for specific window, the data bar is not apply
to all other window.

Installation and Operation Manual
16
2-7 Compass
The chart plotter computes compass direction
from the constellation of GPS satellites. For
the GPS chart plotter to compute direction
the vessel must be moving through the
water.
For easy reading and recognition, there is a
compass needle at top right side.
When the compass is displayed, COG is
always displayed in data field.
Also when you are navigating to a point, COG
and BRG is always displayed in data bar.
Tip
COG(Course Over Ground) –The course you
vessel is heading.
BRG(Bearing) –The direction from your
current position to a destination point.
To turn the compass off or on:
1 Press and select Data bar.
2 Select Compass.

Installation and Operation Manual
17
2-8 Multi window displays
The Chart plotter can display up to four
windows at the same time.
Adding a window
1Press and select Add icon.
2 Select an icon you want to add.
3 Repeat above steps if necessary.
Changing window size
1 Press and select Split icon on
bottom.
2 Press or to change the height of
the windows if there is only two windows. If
the unit is displaying more that three
windows, press , , or to
change the height of the windows.
Deleting a window
1 Press and hold to select a window
you want to delete.
2 Press and select Remove icon to
remove.
Replacing two windows on the
display
1 Press and hold to active desired
window you want to replace.
2 Press , select Replace icon.
3 Select icon you want to display then press
.

Installation and Operation Manual
18
The active window
To distinguish an active window among windows, an orange border indicates the active
window. To change the active window to the next window, press and hold .
Favorite displays
The most commonly used windows are called favorite displays and up to six favorite windows
can be saved. Also each favorite display can have data bar and compass.
Displaying a favorite display
1 Press twice.
2 when above window pops up select a desire display you want.
Adding a favorite display
1 Organize a window as you want.
2 Press to show the main window.
3 Select Save icon at the bottom
4 Select an icon where you want to add your favorite display. If you add the new favorite
display on existing favorite display new display will overwrite the old display.

Installation and Operation Manual
19
2-9 Man overboard (MOB)
During navigation, the “MOB” feature
provides a one-touch method of storing a
location, such as point where a crew member
fell overboard. In this mode, the chart plotter
places a MOB point on the chart page and all
the navigation data shown is related to
navigating back to this point, allowing you to
retrace your path to the MOB point
efficiently.
MOB will not work if the
unit does not have a GPS
fix.
1 When you press , a MOB waypoint is
created.
2 When is pushed not in the Chart
window, the screen automatically is
changed to Chart window and MOB
waypoint is at the center of the chart.
3 If autopilot is connected, the unit sets the
MOB waypoint to be the destination and
start to navigate.
This might result in a
sudden and dangerous turn.
Tip:Even though navigation to MOB
waypoint is canceled, the MOB waypoint is
not be removed from the waypoint list. To
delete the MOB waypoint, you need to delete
it manually.

Installation and Operation Manual
20
3-1 Manual / Auto Power on and off
Manual power on
Press and hold until the display shows
the start up page. When the Warning screen
appears, press to accept.
Manual power off
Press and hold for 5 seconds. A counter
timer appears on the screen, if you release
the button before the countdown timer
reaches zero, the chart plotter will remain On.
Auto power
If the unit is wired for auto then:
•The unit turns on automatically when you
turn on the boat‟s ignition.
•You can not turn off the unit if the ignition
is turned on.
•If Auto power off is set, the unit turns off
automatically when you turn off the boat‟s
ignition.
•If Auto power off is set, the unit will not be
turned off even though the boat‟s ignition is
turned off. To turn off, you need to turn off
the unit manually.
3-2 Brightness, night mode and Background
You can change the screen setting for the
display. To change settings, shortly press .
Brightness
To change the brightness, select
Brightness, and press to dim or to
brighten.
Press to return to the previous
screen.
Night mode
The chart plotter has preprogrammed
settings allowing you to customize the look of
the Chart window. The default is daytime
view. Select Night mood depending on what
mode the display is in at the time of
selection.
To change mode:
1 Highlight Night mode.
2 Press or .
Tip:The screen will be difficult to read if
the chart plotter is in night mood when the
sun is too bright
Background
You can Changes the background color if
necessary. This selection is a personal
preference. Select the option that gives you
the clearest viewing in your weather
conditions and viewing angle.
3 General Operation