Sancon SAMCOM FPAN10A User manual

1
Instruction Manual
Two Way Radio Transceiver SAMCOM FPAN10A
www.sanconsales.com Sancon Inc.

2
SANCON
□ SANCON assumes no responsibility of any damages or loss
resulting from the use of this Manual.
□ SANCON assumes no responsibility for any loss or claims by third
parties which may arise through the use of the FPAN10A.
□ SANCON assumes no responsibility for any damage or loss caused
by deletion of data as a result of malfunctions, repair or battery
replacement.

3
CONTENTS
1. Get Acquaint
■ Installing Battery
■ Installing Antenna
■ Installing Belt Clip
■ Installing optional Speaker/Micrphone
2. Basic Operation
■ Turn Transceiver on
■ Control Volume
■ Select the channel
■ Receiving operation
■ Transmit operation
■ Battery Low alert
3. Battery Charging
4. Additional functions
■ Time out Timer

4
■ Scan
■ Voice Prompt
■ Voice Operated Transmission ( VOX )
■ Battery Saving
■ Busy Channel Lockout ( BCL )
■ CTCSS / DCS
5. Important Precaution

5
1. Getting Acquaint

6
■ Installing the battery.
■ Installing the Antenna
Screw the Antenna into the antenna connector on the top of transceiver.
■ Installing the Belt Clip
Belt clip need to be fixed by 2 pcs of screws on the back side of transceiver.

7
■ Installing the optional Speaker/Microphone
Firstly Pull up the jack cover on the right side of transceiver and connect the
Speaker/Microphone.
Please note that when connecting the Speaker/Microphone, the performance
of shower resistance may reduce its performance.

8
2. Basic Operation
■ Turn transceiver ON.
When delivering the transceiver, transceiver should be powered off. To
power on the transceiver, turning clockwise the Power switch/Volume control
knob. You can hear the turn on message automatically to indicate that
transceiver is power on condition.
■ Control Volume
Press and hold the Monitor button to listen the audio noise. Then adjust the
Power- switch/Volume control knob to set the proper sound level.
Turn clockwise to increase the volume and turn counterclockwise to decrease
the volume.
■ Select the channel.
To select channel, turn the Channel Switch to set the desired channel.
No. 16 channel is the scanning channel.

9
■ Receiving operation.
The LED indicator lights green to indicate the transceiver is under reception
mode. Transceiver equipped with the Squelch function. If field strength is very
weak, transceiver can not generate the audio to keep communication smooth.
But if you want to listen the voice even in the weak field strength, press
Monitor button and hold to listen the noisy voice.
To press the Function button LED torch will light up. If press one time, Touch
will continuously light on and press 2 times to flash Torch.LED.
■ Transmit operation
To transmit the transceiver, press and hold the Press to Talk ( PTT ) button.
Holding the PTT button, you can speak to microphone.
To keep the better condition to transmit the voice, mouth should be away from
the microphone around 2-3 inches.
When transceiver is under transmission LED will light RED color.
Battery low alert
If battery is very low level, Battery low alert will be generated to indicate that
you need to charge the battery.

10
3. Battery Charging
To charge the Transceiver, following are the instructions,
1. Plug the AC power to the Charger unit.

11
2. Check the Charger LED turns green to standby the charger.
3. Insert the Transceiver into the Charger pocket.
4. Check the Charger LED turns red to indicate that charging is operating.
5. After 3 hours from the charging start, LED turns green to indicate the
charging has been successfully done.
6. Remove the Transceiver unit from the charger pocket
4. Additional function
■ Time out timer ( TOT )
TOT is the optional function set by programmer. If TOT is available,
transmission time ( hold the PTT button ) will be limited on certain period of
time. TOT is useful for preventing from the thermal damage when Transceiver
is under long time transmission.
■ Scan
Scan is the optional function set by programmer. If scan function is available,
transceiver can stop the any of channel which are busy.

12
This scan function can be set only for No.16 channel, so you can monitor
maximum of 15 channel with scanning mode.
When channel is stop at certain channel, you can press the PTT button to
transmit. Also press and hold the Monitor button to stop scan operation.
■ Voice message ( Prompt )
Voice prompt function can be valid or invalid by programmer.
If Voice prompt is valid, you can listen the voice when changing the channel or
power switch on.
To activate the Voice prompt function on, keep holding Monitor button and PTT
button together and turn the Transceiver power on.
■ Voice Operated Transmission ( VOX )
VOX is the optional microphone set. If you have VOX function, you do not
need to PTT mode by manual, VOX circuit automatically switch on the
transmission mode
VOX sensing level is bit critical to set. You need to adjust the sensor level at
actual environment and voice level.

13
To activate the VOX function, press and hold monitor button and PTT button
together and turn Transceiver power on at channel 1 to 5.
■ Battery Saving
This is a standard function. To increase the battery life ( decrease battery
consumption ) , Transceiver has battery saving mode Battery saving mode
will start after 10 seconds from the busy condition off.
■ Busy channel Lockout ( BCL )
BCL function is the optional function that can be set by programmer.
If BCL is on, Transceiver can not transmit when Transceiver is under busy
condition. If press PTT button, generate the short beep to indicate that
Transceiver can not transmit due to busy condition.
■ CTCSS / DCS
CTCSS can be set by programmer.
If equipped with CTCSS or DCS, your group can not listen other group
conversation. This function is useful to listen the voice within the group even

14
other group are using same channel.
5. Important Precaution
□ This Transceiver contains precious electronic components. Avoid
temperature extremes during use storage, and do not subject it to strong
impact.
□ Avoid using it in area where it might come into direct contact with liquids
and avoid very high humidity.
□ Never try to open Transceiver or take it apart. Doing so can lead to
serious damage and malfunctions.
□ Clean the Transceiver by wiping it with a soft dry cloth. You can also use
a soft cloth moistened with a weak solution of a mild neutral detergent
and water. Wiping as much liquid as possible from the cloth before
wiping the pager. Never use thinner, benzene, or other volatile agents,
or alcohol to clean the body.

15
□ Do not use allow the Transceiver to be exposed to direct sunlight, heat
from the heaters, or other source from heat ( greater than 60 degree C ).
□ Never expose batteries to direct heat or incinerate them. Doing so may
cause the battery to explode.