S&T embedded Rail-PC-5101 User manual

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Table of contents
Introduction.....................................................................................................................................2
Symbols used in this Manual........................................................................................................................ 2
Important Instructions................................................................................................................................... 2
Note on the Warranty..................................................................................................................................... 2
Technical Short Information ..........................................................................................................2
Order Information...........................................................................................................................2
Dimensions.....................................................................................................................................3
Mounting options............................................................................................................................5
Open the housing...........................................................................................................................7
CPU inside ....................................................................................................................................................... 8
Internal Connector List:.................................................................................................................................... 9
Panel Connector List:..................................................................................................................................... 10
Jumper List:.................................................................................................................................................... 10
Jumper Settings............................................................................................................................................. 11
BIOS Power Setting ..................................................................................................................................... 12
Panel Connector Pin Assignments ................................................................................................................ 14
Internal Connector Pin Assignment ............................................................................................................... 17
24V-to-12VDC – Converter............................................................................................................................ 23

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Introduction
Symbols used in this Manual
This symbol point out to especially information.
Important Instructions
This chapter contains instructions which must be observed when using your Flatman Monitor.
The manufacturer’s instructions provide useful information on your device.
Note on the Warranty
Due to their limited service life, parts which by their nature are subject to a particularly high degree of wear
(wearing parts) are excluded from the warranty beyond that provided by law. This applies to the CMOS
battery, for example.
Technical Short Information
Housing Interfaces
RAL 70 1 powder coated 4x USB3.0
(WxDxH) 180 x 134 x 68mm (Heatsink included) 3x GbE LAN
Weight: 1300g x Display Port
Integrated SBC x COM (RS 3 , RS4 , RS485, BIOS configurable)
CPU Intel® Haswell ULT i5-4300U (option: w/ i7-4650) Power
4GB RAM (option up to 8GB) 16-30V
DC
Input via Phoenix Connector PSC 1,5/ 3-F
Storage: 64GB mSATA SSD (option: up to ?GB) OS Support
Hardware Monitor Windows7, Windows8, Linux
Voltages, Temperature Environment
Fanless passive cooling
EMC Operating temp.: 0 °-50°C ambient
EN550 class B Humidity: 10%-90% @ 39°C, non condensing
Power Consumption U
IN
I
IN
P
IN
Standby 4 V 0,0 0 A 0,5 W
Windows IDLE 4 V 0,308 A 7,4 W
Windows typical workload (BurnIn with max. load) 4 V 0,800 A 19, W
Windows with CPU at TDP (Thermal Design Power selected in Thermal-analysis-tool) 4 V 0,990 A 3,8 W
Windows with max. workload & max. Graphics adjusted in Thermal-analysis-tool &
turbo mode (max. current consumption) 4 V 1,440 A 34,6 W
Test Setup: Windows 7 pro. 64bit; 4GB RAM ; 60GB mSATA
Order Information
Order# escription
EN00-004001-01 RAIL-PC-5101; Intel Haswell i5-4300U, 4GB RAM, 64GB mSATA
EN00-004002-01 RAIL-PC-5101; Intel Haswell i5-4300U, 8GB RAM, 128GB mSATA
EN00-004003-01 RAIL-PC-5101; Intel Haswell i5-4300U, 8GB RAM, 256GB mSATA
EN00-004004-01 RAIL-PC-5101; Intel Haswell i5-4300U, 4GB RAM, 32GB mSATA
EN00-004005-01 RAIL-PC-5101; Intel Haswell i5-4300U, 4GB RAM, 128GB mSATA

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Dimensions

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Mounting options

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Always make sure to mount the DIN rail retaining clamp in upper position
The heatsink is flippable according to the Rail PC mounting. Make sure that the airflow always works in
upright direction.
Important note: For operating mode has to be inserted a thermal grease between heatsink
and mounting plate
(example for heatsink mounting and airflow:)
The small milling boundary of the heatsink has to be mounted to the small rim of the Box housing
mounted with two M4x8 (max. length)
counter sunk bolds

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Open the housing
To open the housing just remove five screws:

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
CPU inside
TPM
(optional)
Speaker Out
3 X RJ45
Connectors
Audio AMP
IS31AP2010B
1 X USB2.0
PIN Header
SPI
4-DI/4-DO
Wafer
USB2.0
Watch Dog
Timer
Super I/O
Fintek
F81803U
2 X COM
Ports
IntelI210-AT
GbE Controller
DP
IntelI210-AT
GbE Controller
2 X Mini-PCIE
Sockets
2 X Speaker
Connectors
2 X Display Port
Connectors
Audio Codec
Reltek
ALC662
USB3.0
1 X DDR3 SO-DIMM
Sockets
1 X LVDS
Connector
GbE PHY
IntelI218-LM
Haswell
ULT
Processors
IN/OUT/MIC
CHRONTEL
CH7511B
4 X USB3.0
Ports
PCIE x1
Block Diagram
SPI Flash
ROM
H/W
Monitor
Audio
PIN Header
DDR3LLVDS eDP
SATA
HD
LPC
2 X SATA
Connector
DI/DO
1x mPCIE / mSATA
1x mPCIE

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Top View:
Internal Connector List:
Label Function
BAT1 Battery Power Input Wafer
BZ1 Onboard Buzzer
CN1 SATA HDD Power Output Wafer
CN5 USB .0 Port 4, 5 Pin Header
CN7 Right Channel 3W Audio AMP Output Wafer
CN8 Left Channel 3W Audio AMP Output Wafer
CN9 Audio Pin Header
CN10 Digital Input / Output Pin Header
CN14 P80_Header LPC
CN15 RS- 3 / 4 / 485 Port 1 Wafer
CN16 RS- 3 / 4 / 485 Port Wafer
CN17 SIM Interface Wafer for MPCIE
CN18 Backlight Power Output Wafer for LVDS1
DIMM1 DDR3 Memory SO-DIMM Socket
FAN1 CPU FAN Wafer
FP1 Front Panel 1 Pin Header
FP Front Panel Pin Header
LVDS1 Primary 4-bit, -channel LVDS Panel Connector
mPCIE1 Mini-PCIE Express v1. Socket / mSATA
mPCIE Mini-PCIE Express v1. Socket
SATA1 Serial ATA Port 0 Connector
SATA Serial ATA Port 1 Connector
/ mSATA

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Panel Connector List:
Label Function
CN USB3.0 Port 0,1 Connector
CN3 USB3.0 Port ,3 Connector
CN11 GbE LAN1 RJ-45 Connector
CN1 GbE LAN RJ-45 Connector
CN13 GbE LAN3 RJ-45 Connector
DP1 DP Connector
DP DP Connector (Dual Mode)
X1 COM1
X COM
PWR Input Power Connector (3pin Phoenix)
Jumper List:
Label Function
JP1 Panel & Backlight Power Selection for LVDS1
JP AT_ATX Mode / MPCIE1 mSATA / mPCIE Selection
JP3 Backlight Power Enable Selection for LVDS1
JP4 MPCIE Activity LED Indication
JP5 USB POWER Selection
JP6 Flash Description Security Over-ride
JP7 RTC Reset Selection
JP8 SRTC Reset Selection

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Jumper Settings
JP1: Panel & Backlight Power Selection for LVDS1 (Pitch 2.54mm)
(not used for Rail-PC-System !!)
Jumper Setting Status
1 1-3 Backlight Power = +1 V
3-5 Backlight Power = +5V
-4 Panel Power = +3.3V
4-6 Panel Power = +5V
JP2: AT_ATX Mode / MPCIE1 mSATA / mPCIE Selection (Pitch 2.54mm)
Jumper Setting Status
1 1-3 ATX Mode
3-5 AT Mode (Default)
-4 mPCIE1 mSATA Selected (Default)
4-6 mPCIE1 mPCIE Selected
21
65

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Importent note:
There is no „power-on-button“ on the device available:
Therefore the jumper JP2 (AT/ATX Mode) has always set to „AT-Mode“!
According to this the BIOS setting for Power Mode is „Power Off“!
(Default settings ex factory)
BIOS Power Setting
Control Group Structure Name BIOS efaults Possible Setting
ACPI Sleep State S3 (Suspend to Ram) Suspend Disabled - S3 (Suspend to Ram)
Restore AC Power LOSS Power OFF Power Off - Power On - Last State
Power Saving Mode Disabled Disabled - Enabled
Resume Event Control
Resume from S3 By PS/ Keyboard Disabled Disabled - Enabled
Resume from S3 By PS/ Mouse Disabled Disabled - Enabled
Resume By PCIE Device Disabled Disabled - Enabled
Resume By RingRTC Alarm Disabled Disabled - Enabled
Resume By RTC Alarm Disabled Disabled - Enabled
► WatchDog Timer Configuration
JP3: Backlight Power Enable Selection for LVDS1 (Pitch 2.00mm)
(not used for Rail-PC-System !!)
Jumper Setting Status
1 1-3 Backlight
Enable Voltage = +3.3V
3-5 Backlight Enable Voltage = +5V
-4 Active High
4-6 Active Low
JP4: mPCIE Activity LED Indication (Pitch 2.54mm)
(not used for Rail-PC-System !!)
Pin escription
1 LED+
LED-
JP5: USB Power Selection (Pitch 2.00mm)
Jumper Status
1- Short USB power will be cut off in S4 & S5 state.
-3 Short USB power will be cut off in Deep S5 state.
21
65
1
2
2
3
1

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
JP6: Flash Description Security Over-ride (Pitch 2.54mm)
Jumper Status
1- Open Disabled
1- Short Enabled
JP7: RTC Reset Selection (Pitch 2.54mm)
Jumper Status
1- Open Normal Operation
1- Short Clear RTC CMOS
JP8: SRTC Reset Selection (Pitch 2.54mm)
Jumper Status
1- Open Normal Operation
1- Short Clear ME Registers
1
2
1
2
1
2

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Panel Connector Pin Assignments
PWR: Input Power Connector
Pin Signal Mating connector
1 GND Phoenix Contact
PSC 1,5/ 3-F
Order# 1841909
Shield
3 VCC
X1: COM1 RS-232/422/485 (via internal cable connection to CN15)
X2: COM2 RS-232/422/485 (via internal cable connection to CN16)
Pin RS-232 RS-422 Half uplex
RS-485
Full uplex
RS-485
1
DCD Tx- DATA- Tx-
RxD Tx+ DATA+ Tx-
3
TxD Rx+ - Rx+
4
DTR Rx- - Rx-
5
GND GND GND GND
6
DSR - - -
7
RTS - - -
8
CTS - - -
9
RI - - -
CN2: USB3.0 Port-0,1 Type-A Connector
Pin Signal Name Pin Signal Name
1 +USBA_VCC 10 +USBB_VCC
USBA_D- 11 USBB_D-
3 USBA_D- 1 USBB_D-
4 GND 13 GND
5 USBA_RX- 14 USBB_RX-
6 USBA_RX+ 15 USBB_RX+
7 GND 16 GND
8 USBA_TX- 17 USBB_TX-
9 USBA_TX+ 18 USBB_TX+
*：The power source of +USBVCC can be selected by JP5.
3
2
1

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
CN3: USB3.0 Port-2,3 Type-A Connector
Pin Signal Name Pin Signal Name
1 +USBA_VCC 10 +USBB_VCC
USBA_D- 11 USBB_D-
3 USBA_D- 1 USBB_D-
4 GND 13 GND
5 USBA_RX- 14 USBB_RX-
6 USBA_RX+ 15 USBB_RX+
7 GND 16 GND
8 USBA_TX- 17 USBB_TX-
9 USBA_TX+ 18 USBB_TX+
*：The power source of +USBVCC can be selected by JP5.
CN11: GbE LAN1 RJ-45 Connector
Pin Signal Name Pin Signal Name
1 TX1+ 5 TX3-
TX1- 6 TX -
3 TX + 7 TX4+
4 TX3+ 8 TX4-
CN12: GbE LAN2 RJ-45 Connector
Pin Signal Name Pin Signal Name
1 TX1+ 5 TX3-
TX1- 6 TX -
3 TX + 7 TX4+
4 TX3+ 8 TX4-
CN13: GbE LAN2 RJ-45 Connector
Pin Signal Name Pin Signal Name
1 TX1+ 5 TX3-
TX1- 6 TX -
3 TX + 7 TX4+
4 TX3+ 8 TX4-
LED Diagram of LAN Connectors:
(front view)
left LE : activity / link right LE : 10/100/1000
off No LAN connectivity off 10 Mbit
yellow link green 100 Mbit
blinking activity orange 1 GbE
left
right

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
DP1: DisplayPort Port-1 Connector
Pin Signal Pin Signal
1 TX0+ 11 GND
GND 1 TX3-
3 TX0- 13 GND
4 TX1+ 14 GND
5 GND 15 AUX+
6 TX1- 16 GND
7 TX + 17 AUX-
8 GND 18 HPD
9 TX - 19 GND
10 TX3+ 0 PWR
DP2: Dual Mode DisplayPort Port-2 Connector *
Pin Signal Pin Signal
1 TX0+ 11 GND
GND 1 TX3-
3 TX0- 13 GND
4 TX1+ 14 GND
5 GND 15 AUX+
6 TX1- 16 GND
7 TX + 17 AUX-
8 GND 18 HPD
9 TX - 19 GND
10 TX3+ 0 PWR
* The Dual-Mode DisplayPort source automatically detects the presence of a plugged-in Dual-Mode DisplayPort cable
adaptor and provides the DVI or HDMI signal, as required, to support the connected DVI or HDMI monitor

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
Internal Connector Pin Assignment
BAT1: Battery Power Input Wafer
Pin Signal Name
1 +VBAT
GND
CN1: SATA HDD Power Output Wafer
Pin Signal Name
1 +1 V
GND
3 GND
4 +5V
CN4: Power Input Wafer (internal cable connection to DC-DC-Converter)
Pin Signal
1 +Vin
GND
3 GND
4 +Vin
CN5: USB2.0 Port 10, 11 Pin Header
(not used for Rail-PC-System !!)
Pin Signal Name Pin Signal Name
1 +USBVCC +USBVCC
3 USB_A- 4 USB_B-
5 USB_A+ 6 USB_B+
7 GND 8 GND
9 KEY 10 GND
*：The power source of +USBVCC can be selected by JP7
CN7: Right Channel 2W Audio AMP Output Wafer
(not used for Rail-PC-System !!)
Pin Signal Name
1 Speaker+
Speaker-
CN8: Left Channel 2W Audio AMP Output Wafer
(not used for Rail-PC-System !!)
Pin Signal Name
1 Speaker+
Speaker-
3
4
1
2
6
1
3
10
4
5
2
87

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
CN9: Audio Pin Header
(not used for Rail-PC-System !!)
Pin Signal Name Pin Signal Name
1 MIC_IN_L MIC_IN_R
3 MIC_IN_JD 4 GND
5 LINE_IN_L 6 LINE_IN_R
7 LINE_IN_JD 8 GND
9 LINE_OUT_L 10 LINE_OUT_R
11 LINE_OUT_JD 1 GND
CN10: Digital Input / Output Wafer
(not used for Rail-PC-System !!)
Pin Signal Name
1 +5V
Digital Input 0
3 Digital Output 0
4 Digital Input 1
5 Digital Output 1
6 Digital Input
7 Digital Output
8 Digital Input 3
9 Digital Output 3
10 GND
CN15 / CN16: RS-232/422/485 Port 1 / 2 Wafer
CN17: SIM Interface Wafer for MPCIE2
(not used for Rail-PC-System !!)
Pin Signal Name
1 UIM_PWR
UIM_DATA
3 UIM_RESET
4 UIM_VPP
5 UIM_CLK
6 GND
12
1 2
11

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
CN18: Backlight Power Output Wafer for LVDS1
(not used for Rail-PC-System !!)
Pin Signal Name
1 BL_ADJ_PWM *
BL_ADJ_VOL *
3 GND
4 +5V / +1 V **
5 +5V / +1 V **
6 GND
7 BL_EN***
*：BL_ADJ can be setting in BIOS setup.
**：Backlight Power can be selected by JP1.
***：BL_EN can be selected by JP3.
DIMM1: DDR3 Memory SO-DIMM Socket
FAN1: CPU FAN Wafer
(not used for Rail-PC-System !!)
Pin Signal
1 GND
+1 V*
3 FAN_RPM
*：PWM Fan control supported.
FP1: Front Panel 1 Pin Header
Pin Signal Pin Signal
1 Reset Button + Speaker +
3 Reset Button - 4 NC
5 HDD LED + 6 Internal Speaker-
7 HDD LED - 8 Speaker -
Note：Internal Buzzer is enabled when Pin6-8 is shorted.
FP2: Front Panel 2 Pin Header
Pin Signal Pin Signal
1 Power LED + Power Button +
3 NC 4 Power Button -
5 Power LED - 6 SMBALERT#
7 BATLOW# 8 SMBus Data
9 GND 10 SMBus Clock
1
3
2
-+
SPKR
+
78
HLED
21
-
+
RSTBTN
-

Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. – 85737 Ismaning - Germany
Phone: [phone] – 0 Fax: [phone]
Mail to: [email protected]
www.snt-embedded.de V1.1
LVDS1: Primary 24-bit, 2-channel LVDS Panel Connector
(not used for Rail-PC-System !!)
Pin Signal Name Pin Signal Name
1 LVDS_A0- 16 LVDS_B1+
LVDS_A0+ 17 GND
3 LVDS_A1- 18 LVDS_B -
4 LVDS_A1+ 19 LVDS_B +
5 LVDS_A - 0 LVDSBCLK-
6 LVDS_A + 1 LVDS_BCLK+
7 GND LVDS_B3-/NC
8 LVDS_ACLK- 3 LVDS_B3+/NC
9 LVDS_ACLK+ 4 GND
10 LVDS_A3-/NC 5 DDC_DATA
11 LVDS_A3+/NC 6 VDDEN
1 LVDS_B0- 7 DDC_CLK
13 LVDS_B0+ 8 +3.3V / +5V *
14 GND 9 +3.3V / +5V *
15 LVDS_B1- 30 +3.3V / +5V *
*：Panel Power can be selected by JP1.