Sanshin SS40E Series User manual

S
S
Sa
a
an
n
nh
h
hs
s
si
i
in
n
n
Patents：
1. U.S. Invention Patent－US 7839035 B2
2. R.O.C. Invention Patent－I 357400
3. R.O.C. Utility Model Patent－M329633 , M329100
4. China Invention Patent－CN 101304205 B
5. China Utility Model Patent－CN 201087053 Y
B
B
B
r
r
ru
u
us
s
sh
h
hl
l
le
e
es
s
ss
s
s
D
D
DC
C
CT
T
Tu
u
ub
b
bu
u
ul
l
la
a
ar
r
rM
M
Mo
o
ot
t
to
o
or
r
rf
f
f
o
o
or
r
r
M
M
M
o
o
ot
t
to
o
or
r
ri
i
iz
z
ze
e
ed
d
d
B
B
Bl
l
li
i
in
n
nd
d
ds
s
s
S
S
Sy
y
ys
s
st
t
te
e
em
m
m
Operation Manual
Apply on：
SS40E series motor
SSRC05E remote control
Thank you for purchasing this product.
To protect your right, please contact the distributor for warranty card.
In the warranty card, be sure to fill the date of purchase and the distributor's name.

- 2 -
Table of Content
Before Using
Safety recautions 3
Name of Each Part 4
Installation 6
Settings
Switch Setting Mode / User Mode 10
Switch blind system 12
Set Connection Between Motor and Remote Control 13
Cancel the Connection 14
Switch Between Forward and Reverse Rotations 15
Set Upper and Lower limits 16
Duplicate Remote Control 18
Cancel『Other』Remote Control 19
Set \ Cancel Preferred Position 20
Operate Preferred Position 21
Quick Command Guide 22
Miscellaneous
Troubleshooting 24
Appendix 25

- 3 -
Before using this product , please read the manual carefully.
After reading , please keep this manual properly for future reference.
In this manual, the precautions indicated as Warnings and Cautions. Please observe the
following precautions to ensure safety.
Warning
This indicates " Possible death or serious injury
may occur ".
Caution
This indicates " Possible injury or material damage
may occur".
Warning
The appliance is not to be used by children or persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction.
Children being supervised not to play with the appliance.
Important safety instructions. Follow all instructions, since incorrect installation can lead
to severe injury.
Do not allow children to play with fixed controls. Keep remote controls away from
children

Frequently examine the installation for imbalance and signs of wear or damage to cables
and springs. Do not use if repair or adjustment is necessary.
Full all-pole disconnection from the supply mains must be provided in the
fixed wiring in accordance with the wiring rules.
Caution
To reduce the fire risk of electric shock or product damage:

Do not expose the equipment to rain, moist, water dripping or water splashing
environment; and do not place objects fully filled with water next to the equipment.
Do not disassemble this equipment.
Do not use any power supply with a voltage not complying with the rated voltage of the
equipment.

If there is any abnormal condition or when it needs repair, please contact your
distributor or the original dealer.
If you find any errors in this manual, or if you are not clear about the
description in this manual, please contact the distributor. Thank you!
Safety Precautions
！
！
！
！

- 4 -
SS40E series Tubular Motor
1. Driving Wheel：
It connects the tubular motor to the aluminum tube so that the motor may drive the aluminum tube
to rotate.
2. Code Button：
It is for setting the communication code between the remote control unit and the tubular motor.
3. Crown.
4. Antenna：
It is for receiving instructions from the remote control unit.
5. AC Power Cord
Name of Each Part
1
2
34 5

- 5 -
SSRC05E remote control unit
（Front） （Real）
6. Up button：
It controls the blinds to move upwards.
7. Stop button：
It controls the blinds to stop, or to switch rotations between forward & backward（P.15）, or to stop
at preferred positions.
8. Down button：
It controls the blinds to move downward.
9. LED channel indicators：
It indicates the window channel – from the left to the right: 1、2、3、4、5;
if all indicators are lit, it is ready to control all windows in a group (group control mode)。
The cycle of indicators is 1→2→3→4→5→all indicators →1.
In the setting mode, only single indicator is lit.
10.Channel selection button：
To select the window channel individually or select the group control mode.
11.Battery cover
6
7
8
9
10
11

- 6 -
1. Select a suitable aluminum tube
2. Insert the tubular motor into tube
Installation
Installation of motorized blinds：
Cylindrical
Aluminum Tube
Inside d
iameter φ40
5㎜13 ㎜
Slot size
Molded
Aluminum Tube
ATD46
Molded
Aluminum Tube
ATD50
a "plastic ring for ATD50"
is required
Molded
Aluminum Tube
ATD51
a "plastic ring for ATD51"
is required
Molded
Aluminum Tube
ATO43
specified tube for venetian
blinds

- 7 -
3. Position the Crown pin into the slot.
4. Fasten the tube at the motor end with screws (not a necessity, may
skip this step).
5. Inset the idler wheel onto tube.
Cylindrical
Aluminum Tube
Molded
Aluminum Tube
Position for inserting the Positioning Pin of the Crown
Positions for
mounting the
screws

- 8 -
6. Fasten the tube at the idler wheel end with screws (not a necessity,
may skip this step)
7. Install the brackets:Measure a suitable distance for installing the brackets to the target
position (in the curtain box or on the wall).
8. Install the motorized blinds:Install the motorized blinds onto the brackets.
9. Connect to the electric power: Connect power cord to AC power before setting and
operation.
N
otice！The positioning slot should be firmly
fixed into the bracket.
Positions for
mounting the
screws

- 9 -
Battery installation
1
3
2
1. Open the battery cover
2. Insert the battery (notice the polarity ○
＋/○ －)
3. Close the battery cover
4. Battery specification: DC 3V (CR2430)
※Notice:
About the battery
The battery provided with the product is prepared for your initial use.
For the battery replacement, please use a battery with the same specifications.
If the remote control is not going to be used for a long time, please take the battery out.
About the remote control:
Please do not install the socket at a location that may be exposed to direct sunlight.
If the Remote Control activates other electronic appliances, please contact the distributor.
Caution:
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s
authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the device.

- 10 -
1. Please switch the remote control to【Setting Mode】when the motor needs settings, and
switch to【User Mode】when the motor is ready to be operated.
2. To switch between【Setting Mode】and【User Mode】should be achieved on the remote
control.
3. Mode check：
Press【Channel】several times. If all five indicators are not lit at the same time, it is in the
【Setting Mode】.
Press【Channel】several times. If all five indicators are lit at the same time, it is in the【User
Mode】.
Switch Setting Mode / User Mode
【Setting Mode】
Press the button 6 times or more,
and only single LED is lit.

Channel
Button
Channel
Button
【User Mode】
Press the button several
times to make sure all LED
are lit .

- 11 -
4. Mode switch:
Open the battery cover on the remote control.
Toggle the【Mode Selection Switch】located above the battery.
Note: It is necessary to use a thin rod to toggle the switch.
After finish toggling【Mode Selection Switch】, close the battery cover immediately.
Schematic Diagram of
Mode Selection Switch
Setting Mode
The switch is at
the right position
User Mode
The switch is at
the left position
2. Toggle the Mode Selection Switch
※Notice:
Unless the motor requires reset, please keep the 【Mode Selection Switch】in【User Mode】.
1. Open the battery cover.
3. After the mode selection is
completed, close the battery
cover immediatel
y
.

- 12 -
1. The tubular motor could operate either【Roller system】or【Venetian system】.
【Roller system】:It could not adjust by degrees on User Mode, but only could on Setting Mode.
【Venetian system】:It could adjust by degrees both on User Mode and Setting Mode.
2. How to switch:
Switch the remote control to【Setting Mode】.
To enter【Roller system】, press both【UP】&【Channel】for 2 seconds until the LEDs lit .
To enter【Venetian system】, press both【DOWN】&【Channel】for 2 seconds until the LEDs
lit
Switch blinds system
Roller system
（Default）
Venetian system
Press the【Up】button
and【Channel】button
simultaneously
Press the【DOWN】button
and【Channel】button
simultaneously
※Notice:
Once the system has been chosen, all channels are in the same system.
Roller System is the initial setting from factory.

- 13 -
1. Switch the remote control to【Setting Mode】（P11）.
2. Channel Selection:
Press【Channel】button to select the channel needs to be connected.
3. Code:To establish a connection between the motor and the remote control.
Press【Code】on the motor for 1 second, the motor will respond “beep “.
Set connection between motor
an
d
r
e
m
o
t
e
co
ntr
o
l
Press the【Code】to start code identification.
Channel
Button

- 14 -
Press【Up】and【Down】simultaneously ; when the motor responds with a “beeping” sound, the code
identification process is complete and the remote control is ready to control this motor.
1. Cancel Connection:
Press 【Code】on the motor for 5 seconds; when the motor responds with a “beeping”
sound, the connection to all remote controls has been cleared.
Beep
Press the【Up】
and【Down】
simultaneously
Press【Code】for 5 seconds to cancel the onnection.
※Notice:
Unless it is necessary to establish connection again, please do not press the【Code】for more than 2
seconds.
To avoid interference, please set the connection one by one in the same building.
Cancel Connection

- 15 -
1. Switch the remote control to【Setting Mode】（P11）.
2. Switch Between Forward and Backward Rotations:
3. Press【Stop】for 3seconds; when the motor responds with a “beeping” sound, the
process for switching between forward and backward rotation is complete.
Switch Between Forward and Backward
Beep
Press 【Stop】
for 3seconds.
※Notice:
Unless it is necessary to change the rotation direction , please do not press 【Stop】for more than 3
seconds.
It requires to reset the upper/lower limit again if the rotation direction has been changed after the
upper/lower limit is set.

- 16 -
1. Switch the remote control to【Setting Mode】（P11）.
2. Enter the Upper Limit Setting Mode:
Press【Up】and【Stop】simultaneously; when the motor responds with a “beeping”
sound, it enters the Upper Limit Setting Mode。
3. Set the Upper Limit:
Use remote control to lift blinds at the target position for setting the upper limit.
During this operation, please perform【Switch Between Forward and Backward
Rotations】if necessary.（P17）.
Press【Stop】and【Channel】simultaneously; when the motor responds with a
“beeping” sound, the upper limit setting is complete.
Set Upper/Lower Limit
Press【Stop】
and【Channel】
simultaneously
Beep
Press【Up】
and【Stop】
simultaneously.
Beep

- 17 -
4. Enter the Lower Limit Setting:
Press【Stop】and【Down】simultaneously, when the motor responds with a “beeping”
sound, it enters the Lower Limit Setting Mode.
5. Set the Lower Limit
Use remote control to lift blinds at the target position for setting the lower limit.
Press【Stop】and【Channel】simultaneously; when the motor responds with a
“beeping” sound, the lower limit setting is complete.
6. If need to reset the upper/lower limit again, please repeat『Step 2~3』or
『Steps 4~5』.
※Notice:
After the【Upper/Lower Limit Setting】is complete, please toggle the【Mode Selection Switch】
back to【User Mode】.
If need to reset the limit position, either upper limit setting or lower limit setting could be executed
separately.
Press【Stop】
and【Down】
simultaneously
Beep
Press【Stop】
and【Channel】
simultaneously
Beep

- 18 -
This function allows to duplicate codes from a remote control to another
without pressing the "Code" button on motor
1. Switch the original remote control (RM-A) and the duplicate one (RM-B) to
【Setting Mode】（P11）.
2. Select the channel needs to be copied on RM-A.
3. Open the battery cover on RM-A, use a thin rod to press shortly on the 【Copy】
button located above the battery, when the motor responds with a beep sound then the
motor is ready to be connected.
4. Select a channel on RM-B which will connect to the motor.
5. Press【Up】and【Down】on RM-B simultaneously, it completes receiving codes when
the motor responds with beep sound.
Use a thin rod to press shortly on the
【Copy】button：
To start "code" function on
motor, allow other remote
controls to connect.
Duplicate Remote Control
Beep
Press the【Up】
and【Down】
simultaneously

- 19 -
This function works if there are many remote controls connect to one motor, to
preserve only one remote control and to cancel the connections between motor
and the other remote controls.
1. Switch the preserved remote control to【Setting Mode】（P11）.
2. Select the channel needs to be preserved.
3. Open the battery cover on preserved remote control, use a thin rod to press for 3
seconds on the【Copy】button located above the battery, when the motor responds
with a beep sound then the connections between motor and the other remote controls
has been deleted except for the preserved one.
Cancel Other Remote Controls
Use a thin rod to press for 3 sec. on
the【Copy】button
※Notice:
Each time to duplicate or delete remote controls, only one channel is allowed. Please repeat the
steps if necessary.
After the【Duplicate codes / Delete codes】is complete, please toggle the 【Mode Selection
Switch】back to【User Mode】.

- 20 -
1. Switch the remote control to【User Mode】（P11）。
2. Each motor could set 2preferred positions exclude the upper and lower
limit.
3. Set preferred position:
Use remote control to lift blinds to target positions.
Press【Stop】and【Channel】simultaneously, it is complete when motor responds with
beep sound.
4. Cancel preferred position:
Use remote control to lift blinds to target preferred positions.（P21）
Press【Stop】and【Channel】simultaneously, it is complete when motor responds
with beep sound.
5. Notice! If 2 preferred positions are configured, the motor will not receive
the command【Set the Preferred Position】any more.
6. If need to change the preferred position, please cancel one of the preferred
position first.
Set / Cancel the Preferred Positions
Press【Stop】
and【Channel】
simultaneously
※Notice:
Before setting the Preferred Position, please make sure that the【Mode Selection Switch】has been
toggled to【User Mode】.
Beep