Oriental motor K II Series User manual

1
Introduction
 Before using the motor
Only qualied personnel should work with the product. Use the product
correctly after thoroughly reading the section “Safety precautions.” In addition,
be sure to observe the contents described in warning, caution, and note in this
manual.
The product described in this manual has been designed and manufactured
to be incorporated in general industrial equipment. Do not use for any other
purpose. Oriental Motor Co., Ltd. is not responsible for any damage caused
through failure to observe this warning.
 Overview of the product
Products described in this manual are induction motors of the KⅡSeries.
Use a pinion shaft type motor in combination with a parallel shaft GV gearhead.
Safety precautions
The precautions described below are intended to prevent danger or injury to
the user and other personnel through safe, correct use of the product. Use the
product only after carefully reading and fully understanding these instructions.
WARNING
Handling the product without observing the
instructions that accompany a "WARNING" symbol
may result in serious injury or death.
CAUTION
Handling the product without observing the
instructions that accompany a "CAUTION" symbol
may result in injury or property damage.
Note
The items under this heading contain important
handling instructions that the user should observe
to ensure safe use of the product.
WARNING
•Do not use the product in explosive or corrosive environments, in the
presence of ammable gases, in places subjected to splashing water, or near
combustibles. Doing so may result in re, electric shock or injury.
•Only qualied and educated personnel should be allowed to perform
installation, connection, operation and inspection/troubleshooting of the
product. Handling by unqualied and uneducated personnel may result in
re, electric shock, injury or damage to equipment.
•Do not transport, install, connect or inspect the product while the power is
supplied. Always turn o the power before carrying out these operations.
Electric shock or damage to equipment may result.
•Turn o the power in the event the overheat protection device (thermal
protector) is triggered. Failure to do so may result in injury or damage to
equipment, since the motor will start abruptly when the overheat protection
device (thermal protector) is automatically reset.
•The motor is ClassⅠequipment. Install the motor so as to avoid contact with
hands, or ground it to prevent the risk of electric shock.
•Keep the input power voltage within the specied range. Failure to do so may
result in re or electric shock.
•Securely connect the cables in accordance with the connection diagram.
Failure to do so may result in re or electric shock.
•Do not forcibly bend, pull or pinch the lead wire or cable. Doing so may result
in re, electric shock or damage to equipment.
•Be sure to insulate the connection terminal of the capacitor. Failure to do so
may result in electric shock.
•Turn o the power in the event of a power failure. Or the motor may suddenly
start when the power is restored and may cause injury or damage to
equipment.
•Do not touch the connection terminal of the capacitor immediately after the
power is turned o (for a period of 30 seconds). The residual voltage may
cause electric shock.
•Do not disassemble or modify the motor. This may result in electric shock,
injury or damage to equipment. Refer all such internal inspections and repairs
to the branch or sales oce from which you purchased the product.
CAUTION
•Do not use the motor beyond the specications. Doing so may result in re,
electric shock, injury or damage to equipment.
•Do not lift up the motor by holding the output shaft, lead wire or cable. Doing
so may result in injury.
•Do not touch the motor output shaft (end or pinion) with bare hands. Doing
so may result in injury.
•Keep the area around the motor free of combustible materials. Failure to do
so may result in re or a skin burn(s).
•Do not leave anything around the motor that would obstruct ventilation.
Doing so may result in damage to equipment.
•Provide a cover over the rotating part (output shaft). Failure to do so may
result in injury.
•Do not touch the motor while operating or immediately after stopping. The
surface of the motor is hot and it may cause a skin burn(s).
•Do not touch the rotating parts (output shaft, cooling fan) while operating
the motor. Doing so may result in injury.
•When an abnormality is noted, turn o the power immediately. Failure to do
so may result in re, electric shock or injury.
•The motor surface temperature may exceed 70 °C (158 °F)
even under normal operating conditions. If the operator
is allowed to approach the motor in operation, attach a
warning label in a conspicuous position as shown in the
gure. Failure to do so may result in a skin burn(s). Warning label
Preparation
 Checking the product
Verify that the items listed below are included. Report any missing or damaged
items to the branch or sales oce from which you purchased the product.
zMotor
Motor ................................................................................... 1 unit
Capacitor ............................................................................ 1 piece
Capacitor cap.................................................................... 1 piece
Instructions and Precautions for Safe Use.............. 1 copy
zParallel shaft GV gearhead (sold separately)
Gearhead............................................................................ 1 unit
Screw set ............................................................................. 1 set
Hexagonal socket head screw, plain washer, spring washer: 4 pieces each
Hexagonal socket head screws for assembling motor: 2 pieces
Parallel key: 1 piece
HM-9441
OPERATING MANUAL Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety
precautions.
•Please read it thoroughly to ensure safe operation.
•Always keep the manual where it is readily available.
KⅡSeries Induction Motor

2
 Checking the model name
Check the model names of the motor and the gearhead against the model
name described on each nameplate.
The gures show the lead wire type.
Motor
Gearhead
Protective Earth Terminal
: Enter a motor classication representing the power supply voltage.
JA: Single-phase 100 V 50/60 Hz JC: Single-phase 200 V 50/60 Hz
UA: Single-phase 110/115 V 60 Hz EC: Single-phase 220/230 V 50/60 Hz
: Enter a number representing the gear ratio of the gearhead.
zPinion shaft type
Lead wire type
Model Applicable gearhead Degree of
protection
Model Gear ratio
2IK6GV-2GVB2to 360
IP20
3IK15GV-3GVB2to 360
4IK25GV-4GVB2to 360
5IK40GV-5GVB2to 300
5IK60GVH-5GVHB2to 300
5IK90GVR-5GVRB3to 180
A decimal gearhead can be assembled with 6 W to 40 W motors.
Using a decimal gearhead makes the gear ratio to ten times as the gear ratio of
the gearhead.
Terminal Box Type
Model Applicable gearhead Degree of
protection
Model Gear ratio
4IK25GV-T2 4GVB2to 360 IP66
5IK40GV-T2 5GVB2to 300
5IK60GVH-T2 5GVHB2to 300 IP54
5IK90GVR-T2 5GVRB3to 180
Combination of motors and gearheads
Combine a motor and a gearhead having the same frame size and pinion shaft
type as shown below.
<Example>
5 IK40 GV -JA 5 GV 25B
Type of pinion
Frame size
• Motor model name • Gearhead model name
zRound shaft type
For the degree of protection for the round shaft type, the motor mounting
surface is excluded.
Lead wire type Terminal Box Type
Model Degree of
protection Model Degree of protection
2IK6A-
IP20
4IK25A-T2 IP66
3IK15A-5IK40A-T2
4IK25A-5IK60A-T2 IP54
5IK40A-5IK90A-T2
5IK60A-
5IK90A-
Installation
 Location for installation
Install it in a well-ventilated location that provides easy access for inspection.
[ Common conditions ]
•Operating ambient temperature
Classication representing the power supply voltage
JA/JC: −10*to +50 °C (+14 to +122 °F) (non-freezing)
UA/EC: −10*to +40 °C (+14 to +104 °F) (non-freezing)
*The lowest temperature is 0 °C (+32 °F) for gearheads of the gear ratio 2
and 3.
•Operating ambient humidity 85% or less (non-condensing)
•Area that is free from an explosive atmosphere or toxic gas (such as sulfuric
gas) or liquid
•Area not exposed to direct sun
•Area free of excessive amount dust, iron particles or the like
•Area free of excessive salt
•Area not subject to continuous vibration or excessive shocks
•Area free of excessive electromagnetic noise (from welders, power machinery, etc.)
•Area free of radioactive materials, magnetic elds or vacuum
•Altitude Up to 1000 m (3300 ft.) above sea level
[ Degree of protection IP66 rated motor ]
•Indoors
•Not exposed to oil (oil droplets) or chemicals.
The motor can be used in an environment that is splashed with water
(excluding the mounting surface of the round shaft type).
Not available for use under high pressure jets of water or immersion in water.
[ Degree of protection IP54/20 rated motor ]
•Inside an enclosure that is installed indoors (provide vent holes)
•Area not subject to splashing water (storms, water droplets), oil (oil droplets)
or other liquids
Note On rare occasions, grease may ooze out from the gearhead. If there
is a concern over possible environmental damage resulting from
the leakage of grease, provide an oil tray or similar oil catching
mechanism in order not to cause a secondary damage. Grease
leakage may lead to problems in the customer's equipment or
products.
 Installation method
Note Do not install the motor to the mounting hole diagonally or
assemble the motor forcibly. Doing so may cause damage to the
motor.
zPinion shaft type
Assembling the gearhead to the motor
1. Keep the pilot sections of the
motor and gearhead in parallel,
and assemble the gearhead with
the motor while slowly rotating it
clockwise/counterclockwise.
At this time, note so that the pinion
of the motor output shaft does not
hit the gearhead or gears strongly.
2. Check no gaps remain between the
motor and gearhead, and tighten
them with hexagonal socket head
screws for assembling motor
(2pieces).
When using a decimal gearhead,
install it between the motor and the
gearhead.
Pinion of
the motor
output shaf
t
P
ilot section
Assemble the gearhead to the motor
in a condition where the motor output
shaft is in an upward direction.
Hexagonal socket head screws for assembling motor*
Gearhead model Screw size Tightening torque
2GVB,3GVB,4GVBM2.6 0.4 N·m (3.5 lb-in)
5GVB,5GVHB,5GVRBM3 0.6 N·m (5.3 lb-in)
*Included with gearheads (sold separately)

3
Note
•Do not forcibly assemble the motor and gearhead. Also, prevent
metal objects or foreign substances from entering in the
gearhead. The pinion of the motor output shaft or gear may be
damaged, resulting in noise or shorter service life.
•O-rings are attached on the motor ange and the mounting surface
of the decimal gearhead. Install the gearhead so as not to pinch the
O-rings. Grease in the gearhead may leak.
Assembling the gearhead to the motor
Secure the motor with mounting screw set (supplied) through the four mounting
holes provided.
Do not leave a gap between the motor and mounting plate.
Motor
Hexagonal socket
head screw
Gearhead
Mounting plate
Spring washer
Plain washer
Included with gearheads
MotorMotor
Gearhead
Gearhead
(L2)
L1
(L2)
L1
①②
Decimal gearhead
Mounting screw set*Material: Stainless steel
Model Gear ratio
Hexagonal socket head
screw L2 [mm
(in.)]
Tightening
torque
Screw size L1 [mm
(in.)]
2IK6
①
2, 3, 30 to 120
M4
55 (2.17) 8 (0.31)
1.4 N·m
(12.3 lb-in)
5 to 25 50 (1.97) 7 (0.28)
150 to 360 60 (2.36) 8 (0.31)
②500 to 1200 90 (3.54) 14 (0.55)
1500 to 3600 9 (0.35)
3IK15
①
2, 3, 30 to 120
M6
65 (2.56) 12 (0.47)
5.0 N·m
(44 lb-in)
5 to 25 60 (2.36) 12 (0.47)
150 to 360 70 (2.76) 12 (0.47)
②500 to 1200 100 (3.94) 13 (0.51)
1500 to 3600 8 (0.31)
4IK25
①
2, 3, 30 to 120 65 (2.56) 9 (0.35)
5 to 25 60 (2.36) 9 (0.35)
150 to 360 70 (2.76) 9 (0.35)
②500 to 1200 110 (4.33) 15 (0.59)
1500 to 3600 10 (0.39)
5IK40
①
2, 3, 25 to 100
M8
85 (3.35) 16 (0.63)
12.0 N·m
(106 lb-in)
5 to 18 70 (2.76) 14 (0.55)
120 to 300 90 (3.54) 15 (0.59)
②360 to 1000 130 (5.12) 18 (0.71)
1200 to 3000 12 (0.47)
5IK60 ①
2, 3, 25 to 100 85 (3.35) 16 (0.63)
5 to 18 70 (2.76) 14 (0.55)
120 to 300 90 (3.54) 15 (0.59)
5IK90 ①
3, 18 to 36 85 (3.35) 16 (0.63)
5 to 15 70 (2.76) 14 (0.55)
50 to 180 95 (3.74) 14 (0.55)
*Included with gearheads (sold separately)
zRound shaft type
Use the hexagonal socket head screws (not included) to secure the motor to
the mounting plate. Do not leave a gap between the motor and mounting
plate.
Motor
Mounting plate
Model Screw size Tightening torque
2IK M4 1.8 N·m (15.9 lb-in)
[1.4 N·m (12.3 lb-in)]
3IK M5 3.8 N·m (33 lb-in)
[3.0 N·m (26 lb-in)]
4IK
5IK M6 6.4 N·m (56 lb-in)
[5.0 N·m (44 lb-in)]
The brackets [ ] indicate the value for stainless steel.
zMotor with cooling fan
When installing a motor with cooling fan onto a device, leave 10 mm (0.39 in.)
or more behind the fan cover or open a ventilation hole so that the cooling
inlet on the back of the motor cover is not blocked.
zMounting the capacitor
Mount the capacitor securely by using M4 screws
(not provided).
Ø4.3 mm
(0.169 in.)
Note
•Do not let the screw fastening torque exceed 1 N·m (8.8 lb-in) to
prevent damage to the mounting foot.
•Mount capacitor at least 10 cm (3.94 in.) away from the motor. If it
is located closer, the life of the capacitor will be shortened.
 Installing a load
The gearhead shaft is provided with a key slot
for connecting the transmission parts. When
connecting the transmission parts, ensure that
the shaft and parts have a clearance t, and
always x the parallel key to the output shaft
with a screw to prevent the parts from rattling or
spinning.
Screw
Parallel key
Gearhead
output shaft
Note Do not apply excessive force onto the output shaft of the gearhead
using a hammer or other tools. Doing so may cause damage to the
output shaft or bearings.
zWhen using the output shaft end tapped hole of a gearhead
Use a tapped hole provided at the end of the output shaft as an auxiliary means
for preventing the transfer mechanism from disengaging.
2GVB, 3GVBtype have no output shaft end tapped hole.
Gearhead model Output shaft end
tapped hole Fixed screw
Screw
Spacer
Transmission
parts
4GVBM5, Eective depth
10 mm (0.39 in.)
5GVB
5GVHB
5GVRB
M6, Eective depth
12 mm (0.47 in.)

4
Connection
Insulate all the wire connections, such as the connection between the motor
and the capacitor connection.
zConnecting Protective Earth Terminal
Be sure to ground the motor using the Protective Earth Terminal on the motor.
Use a crimp terminal described below for grounding.
Applicable crimp terminal: Insulated round crimp terminal
Terminal screw size: M4
Tightening torque: 1.0 to 1.3 N·m (8.8 to 11.5 lb-in)
Applicable minimum lead wire size: AWG18 (0.75mm2) or thicker
Ø4.1 (0.16) or more
[ Unit: mm (in.) ]
4.8 (0.19) or less
9.5 (0.37)
or less
Note Be sure to use the screw for grounding attached on the product.
 Connection diagram
The rotation direction of the gearhead output shaft may vary from that of the
pinion shaft type motor depending on the gear ratio of the gearhead assembled.
Check the motor model name and the gear ratio before connecting.
The connection diagram is an example of the lead wire type.
Models for the gear ratio and the round shaft type rotate as shown in
the connection diagram.
Models for the gear ratio rotate in the opposite direction from the
connection diagram.
Motor
model Gear ratio
2IK6
3IK15
4IK25
2 3 5 6 7.5 9 12.5 15 18 25 30 36
50 60 75 90 100 120 150 180 250 300 360 500
600 750 900 1000 1200 1500 1800 2500 3000 3600 − −
5IK40
2 3 5 6 7.5 9 12.5 15 18 25 30 36
50 60 75 90 100 120 150 180 250 300 360 500
600 750 900 1000 1200 1500 1800 2500 3000 − − −
5IK60
2 3 5 6 7.5 9 12.5 15 18 25 30 36
50 60 75 90 100 120 150 180 250 300 − −
5IK90 −3 5 6 7.5 9 12.5 15 18 25 30 36
50 60 75 90 100 120 150 180 − − − −
CW
CW
power supply
N
Red (U2)
Black (U1)
L
Grounding
White (Z2)
CCW
CCW
power supply
N
Red (U2)
Black (U1)
L
White (Z2)
Grounding
A code in the parentheses ( ) represents a terminal code of the terminal box type.
zContact protection
In order to protect contacts, connecting a CR circuit for surge suppression is
recommended.
It is provided as a peripheral equipment (sold separately).
Model: EPCR1201-2
 Capacitor connection
When crimp terminals are used, use the FASTON
terminals 187 Series (TE Connectivity).
Use the supplied capacitor cap to insulate the
capacitor terminal connection.
Capacitor
187 series
Capacitor cap
Note For lead wire connection, use one lead wire for each individual
terminal.
 Connection method to a terminal block
Remove the terminal box cover for the terminal box type, and connect a cable.
Cables for connection are available as accessories (sold separately).
•If the O-ring that has set in the matching surface of the terminal box cover
falls o, install it securely in the groove portion of the terminal box cover.
•After connecting the cable, securely tighten with the tightening torque in the
table below.
Note
•To make shielding function fully eective, use a cable of an
appropriate diameter and observe the specied tightening torque
of screws.
•Secure the cable drawn from the motor terminal box so that it
does not receive stress.
Terminal box cover mounting
screw (M4-4 pieces)
Terminal box cover
Mounting screw
for terminal (M4)
Terminal box
Nipple
Tightening
nut
Protective Earth
Terminal (M4)
Cable glan
d
Terminal codes : Z2 U2 U1
Terminal block
Tightening torque [Unit: N·m (lb-in)]
Terminal box cover mounting screw 1.0 to 1.5 (8.8 to 13.2)
Mounting screw for terminal 1.0 to 1.2 (8.8 to 10.6)
Tightening nut 2.0 to 2.5 (17.7 to 22)
Nipple 2.0 to 2.5 (17.7 to 22)
Protective Earth Terminal 1.0 to 1.5 (8.8 to 13.2)
•When connecting the cable on the terminal block, use the following cable
and crimp terminal.
Applicable crimp terminal: Insulated round crimp terminal
Applicable cable diameter: Ø7 to Ø13 mm (Ø0.28 to Ø0.51 in.)
Applicable lead wire: AWG18 (0.75 mm2) or thicker
[Unit: mm (in.)]
Ø4.3 (0.17) or more
18 (0.71) or less
8 (0.31) or less

5
zChanging the cable outlet position
The cable outlet position can be changed to the left or right 90-degree
direction, or the 180-degree direction.
When changing the direction of the cable outlet position, loosen the terminal
box mounting screws, and rotate the terminal box to change the mounting
direction.
T
erminal box mounting screw
(M4-4 pieces.)
T
ightening torque:
1.0 to 1.5 N·m (8.8 to 13.2 lb-in)
Terminal box
Gasket
Motor case
Note
•Be sure to use the gasket which has been put in the product at the
time of shipment.
•Assemble not to enter any foreign object between the terminal
box and motor case.
Operation
The motor rotates when the power supply is turned on.
For protection against electric shock, do not turn on the power supply until the
wiring is complete.
Note
•Make sure that the motor case temperature does not exceed
90 °C (194 °F) when operating the motor. Operation exceeding
case temperature 90 °C (194 °F) may signicantly deteriorate
the coils and ball bearings of the motor and shorten the motor's
life span. Motor case temperature can be measured by xing a
thermometer on the motor surface. It can also be measured using
thermo tape or a thermocouple.
•To change rotation direction of the motor, wait until the motor
completely stops. Otherwise its direction may not change or may
take much time to change.
•Care should be taken when using in a low-temperature
environment as the transmission eciency will drop along with
the output torque.
•Use a supplied capacitor, and always keep it connected even after
the motor is started.
Time rating
Continuous operation is possible (continuous rating).
Maintenance and inspection
 Inspection
It is recommended that periodic inspections would be conducted for the items
listed below after each operation of the motor. If an abnormal condition is
noted, discontinue any use and contact your nearest Oriental Motor sales oce.
zInspection item
•Check if any of the mounting screws of the motor and gearhead are loose.
•Check if the bearing part (ball bearings) of the motor generates unusual
noises.
•Check if the bearing part (ball bearings) or gear meshing part of the gearhead
generates unusual noises.
•Check if the output shaft of the motor and gearhead and a load shaft are out
of alignment.
 Warranty
Check on the Oriental Motor Website for the product warranty.
 Disposal
Dispose the product correctly in accordance with laws and regulations, or
instructions of local governments.
Locked rotor burnout protection
This motor is equipped with one of the two features listed below to prevent the
motor from burning out as a result of abnormal heating which may be caused
by misapplication.
 Thermal protection
"TP" is stamped on the motor nameplate. The motor has an "auto reset"
type thermal protector built into its motor coil. When the motor reaches a
predetermined temperature, the internal thermal protector is activated and the
motor is stopped.
Always turn the power o before performing inspections.
Thermal protector activation range:
Power is turned o at 130±5 °C (266±9 °F)
Power is turned back on at 85±20 °C (185±36 °F)
 Impedance protection
"ZP" is stamped on the motor nameplate. The motor has higher coil impedance.
When the motor goes into locked rotor condition due to a malfunction, coil
impedance rises, suppressing input power to the motor and protecting the
motor coil from burnout.
Troubleshooting
When the motor cannot be operated correctly, refer to the contents provided
in this section and take appropriate action. If the problem persists, contact your
nearest oce.
Phenomena Check items
Motor does not rotate.
Motor sometimes rotates
and stops.
•Check the power supply voltage.
•Connect the power supply and the motor
correctly.
•Connect the supplied capacitor correctly.
•If terminal blocks or crimp terminals are used,
check them for poor connection.
•Keep the load at or below the allowable value.
The motor rotates in the
direction opposite to the
specied direction.
•Connect the supplied capacitor correctly.
•The connection varies depending on the gear
ratio of the gearhead.
•The rotation direction is as viewed from the
output shaft end. Check the reference direction.
Motor temperature
abnormally high
[Motor case temperature
exceeds 90 °C (194 °F) ]
•Check the power supply voltage.
•With a single-phase motor, connect thesupplied
capacitor correctly.
•Review the ventilation condition.
Noisy operation
•Assemble the motor and gearhead correctly.
•Assemble a gearhead of the same pinion type as
the motor.

6
•Unauthorized reproduction or copying of all or part of this manual is
prohibited.
•Oriental Motor shall not be liable whatsoever for any problems relating
to industrial property rights arising from use of any information, circuit,
equipment or device provided or referenced in this manual.
•Characteristics, specications and dimensions are subject to change without
notice.
•While we make every eort to oer accurate information in the manual,
we welcome your input. Should you nd unclear descriptions, errors or
omissions, please contact the nearest oce.
•is a registered trademark or trademark of Oriental Motor Co.,
Ltd., in Japan and other countries.
© Copyright ORIENTAL MOTOR CO., LTD. 2022
Published in March 2022
T
echnical Support Tel:[phone]
8:30am EST to 5:00pm PST (M-F)
www
.orientalmotor.com
• Please contact your nearest Oriental Motor oce for further information.
Schiessstraße 44, 40549 Düsseldor
f, Germany
T
echnical Support Tel:[phone]
www
.orientalmotor.de
Unit 5 F
araday Oce Park, Rankine Road,
Basingstoke
, Hampshire RG24 8QBUK
T
el:[phone]
www
.oriental-motor.co.uk
T
el:[phone]
www
.orientalmotor.fr
T
el:[phone]
www
.orientalmotor.it
4-8-1Higashiueno
,Taito-ku,Tokyo 110-8536
Japan
T
el:[phone]
www
.orientalmotor.co.jp
Tel:[phone]
www.orientalmotor.com.cn
Tel:[phone]
www.orientalmotor.com.tw
Singapore
Tel:[phone]
www.orientalmotor.com.sg
Tel:[phone]
www.orientalmotor.com.my
Tel:[phone]
www.orientalmotor.co.th
Korea
Tel:[phone]
www.inaom.co.kr
Tel:[phone] (For English)
1800-121-4149 (For Hindi)
www.orientalmotor.co.in
Regulations and standards
 UL Standards, CSA Standards
This product is recognized by UL under the UL and CSA Standards.
 CE Marking
This product is axed the CE Marking under the Low Voltage Directive.
zLow Voltage Directive
Applications standards
EN 60034-1, EN 60034-5, EN 60664-1
Momentary excess torque based on EN 60034-1
Model Momentary excess torque Momentary excess torque represents
a maximum torque that can maintain
the operation for 15 seconds without
stalling or abrupt speed change even
if the torque is increased gently while
operating at rated voltage and rated
frequency.
2IK6
3IK15 120% of the rated torque
4IK25
5IK40
5IK60
130% of the rated torque
5IK90 140% of the rated torque
Installation conditions
Lead wire type: Overvoltage categoryⅡ, Pollution degree 2, ClassⅠequipment
Terminal box type: Overvoltage categoryⅡ, Pollution degree 3, ClassⅠequipment
When the machinery to which the motor is mounted requires overvoltage
categoryⅢspecications, install the motor in a cabinet that connect to power
supply via an isolation transformer.
 RoHS Directive
This product does not contain the substances exceeding the restriction values.
 China Compulsory Certication System (CCC System)
This product is axed with the CCC Mark under the China Compulsory
Certication System.
It is also certied by the China Quality Certication Center (CQC).