Sanus VISIONMOUNT LRF118 User manual

-
/\
N
o
V
IJ"l
N
~
o
o
oI
~
o
0\
~
~Pt..I'IIl.J ~ VISIONMOUNT
LRFl18
Thank you for choosing the Sanus Systems LRFl18 wall mount. The Sanus Systems LRFl18
wall
mount is designed to supporta monitor sized up to 50 in. (127cm) and weighing up
to 59 kg (130 Ibs). The mount is adjustable; it will tilt +5° to -15°, swivel to ±90°,and roll ±6°.
This product must be used
with the Sanus Systems LR1 A, sold separately.
r------------- AWARNING ---------------,
This product contains small items that could be achoking hazard if swallowed.
Keep these items
away from young children!
r-------------A CAUTION ------------,
This product is designed for use in wood stud walls only! The wall must be capable of
supporting up to five times the weight of the monitor and mount combined. If you
have any doubts about the ability
of the wall to support the monitor, contact Sanus
Customer Service, or aqualified contractor.
r-------------A CAUTION-----------...,
Do not use this product for any purpose not explicitly specified by Sanus Systems.
Improperinstallation
or use may cause personal injury and/or propertydamage. If
you do not understand these instructions, or if you have doubts about the safety
of the installation, contact Sanus Customer Service. Sanus is not liable for injury or
damage caused by incorrect installation or use.
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA
USA Customer Service 1-800-359-5520· www.sanus.com

Supplied Parts and Hardware
Before starting assembly· verify all parts are included and undamaged- Ifany parts are missing or damaged· do not return the item
to your dealer; contact Sanus Customer Service- Never use damaged parts!
o
o
1/4-20
[14] X4
[08] X1
[22] X4
[18]
x4
o
[04] x4
[17] X4
~ ~"m","" -=D
[13] X4
[07] X7
[21] X4
[02] X2
[03] X2
[01] X1
~9
,
0:
o
~
0:
~~
[05] X2[06] X7
@
(»
0@
M4 MS
M6 M8
[09] x4 [10] X4[11] X4 [12] X4
~
~
M4x 12mm
M5x 12mm
[15] X4[16] X4
~
, ' " I
M4x30mm I
[19] X4[20] X4
00
Q9)
/
~-
/
10
(/[27] X1
\ ~
M4/MS
M6/M8
M6/M8
[23] X8[24] X4[25] X4[26] X46901-100125
<02>

1:Attach Brackets to Monitor
For Monitors with aFlat Back
6901-100125 <02>
~
~09]'[10]'
[11],[12J
25], [26J
[19J, [20J,
[21J,[22J~--~ .... _...... ~
t:l
For Monitors with aCurved Back or Obstruction
Use washer [23J with M4 or MS
hardware only.
8[23J
[251,[261 0
e

2: Install Vise Assemblies
o •
{; 1
.----------- NOTE ----------,
Do not overtighten the nut [14].The vise assembly [04] must
rotate freely around
the carriage bolt [13].
3: Install Arm Assembly to Monitor
"
[03]
,.---- NOTE --------,
Do not overtighten the fastener in
the vise assemblies [04]. Tighten
only enough to prevent the tubes
[03] from moving.
6901-100125 <02>

4: Install Preventer
Install the preventer [08] on the left side if
you want the arm to fold to the left. Install
the preventer on the
right side if you want
the arm to fold to the right.
5: Attach Arm to Wall Mount
6901-100125 <02>
HEAVY! You will need
assistance
with this step.
[A] ~
.--------- NOTE --------,
Refer to the instructions included with the LRl Afor
proper installation
of the wall mount [A].

ACAUTION
Avoid potential injuries
or property damage! Refer to the instructions
included
with the LRl A for proper installation of the safety fasteners
[A], [B), and [C]. Periodic maintenance may be required.
tZ! 6: Secure Arm to Wall Mount
f:
7: Install Cable Management
[07] ~
.'
I
I
I
I
NOTE
Be sure to leave enough slack in the cables to allow the
monitor to move freely. Use the cable ties [06] and wire
clips
[07] to secure the cables to the brackets [02] and arm
[01].
6901-100125 <02>

6901-100125 <02>
8: Adjust Monitor Position
Adjust Level
Adjust Left IRight Swivel
ACAUTION
Avoid potential injuries or propertydamage! Remove the safety
bracket [B) only
to adjust the swivel tension nut [C]. Be sure to replace
the safety bracket after adjusting the swivel tension nut.The hex hole
in
the safety bracket must seat over the swivel tension nut.

a
.------NOTE --------,
Adjust the pitch tension by tightening or
loosening the tension knobs
[0].
Extend or Retract Arm
Adjust Up IDown Pitch
.----- ACAUTION -------,
Avoid potential injuries or property damage!
Do not remove the adjustment nut
[E];
tighten or loosen only as necessary for easy
arm adjustment.
6901-100125 <02>
CSAV, Inc. and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein
covers all details, conditions. or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to
change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy,
completeness or sufficiency of the information contained in this document.

Instructions for Installation of Safety Bracket
Step 1: Tighten Main Support Nut
Identify Safety Bracket as shown below. Extend TV away from wall and tilt it down. Using Safety Bracket as awrench,
tighten Main Support Nut
by turning clockwise. Threaded Shaft should be visible above the Nut as shown in Detailed View
of Diagram 1. Do not over-tighten. Adjust Main Support Nut until one edge is parallel with the TV.
Caution: Turning counterclockwise will loosen Main Support Nut and may cause TV to fall, resulting in property
damage or personal injury. If you have any doubts or questions in regards to this installation, please call Sanus or
a qualified installation professional.
Diagram 1
Safety
Bracket
Step 2: Install Safety Bracket
Slide Safety Bracket around and over Threaded Shaft Block of Wall Mount. The hole in the top of Safety Bracket must line
up with Main Support Nut and fit over it. See the Pre Installation and Post Installation Diagrams below. Add Safety Sticker
to the arm
of the VMSA once the Safety Bracket has been installed.
NOTE: Safety Bracket MUST slide completely down over Main Support Nut. If alignment of Main Support Nut
prevents Safety Bracket from sliding completely down over Main Support Nut, then Main Support Nut must be
adjusted slightly to provide proper alignment. Under no circumstances should Main Support Nut ever be loosened
more than one-quarter turn.
Pre Installation
Detailed View