Sanus CFA16SM User manual

Customer Service
Americas: 800-359-5520 • 952-225-6013 • [e-mail]
Europe, Middle East, and Africa: [phone] • [e-mail]
Asia Pacic: 86 755 8996 9226 • [e-mail]
SANUS • 6436 City West Parkway • Eden Prairie, MN 55344 USA
©2012 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone.
All other brand names or marks are used for identication purposes and are trademarks of their respective owners.
sanus.com
We are here to help!
Please contact Customer Service with any questions.
CFA16SM
Instruction Manual

2
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Specifications
Weight-DO NOT EXCEED: 90.7 kg (200 lb.) includes rack and any components or accessories
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose not explicitly specied by manufacturer
The wall must be capable of supporting ve times the weight of the rack and components or accessories combined
If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product,
contact Customer Service or call a qualied contractor
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
English
Required Tools
13mm
(1/2 in.)
5.5mm
(7/32 in.)
10mm
(3/8 in.)

3
Supplied Parts
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your
dealer; contact Customer Service. Never use damaged parts!
[01] x 2
[02] x 8 [03] x 8 [04] x 8
5/16 x 3½ in.
[05] x 4 [09] x 2
[08] x 4
[07] x 2
[06] x 2

4
Determine which conguration best
suits your needs. Attach the rack arm
of both swing arms [01] to the back
brace of the rack using carriage bolts
[02], washers [03], and lock nuts [04].
The swing arms [01] can be mounted
as a left hinged conguration or a right
hinged conguration.
Attach Swing Arm to Rack Assembly
[01]
Left Hinge
Right Hinge
[01]
[01]
[02]
[04]
[03]
[01]

5
1 2
Locate studs. Verify the center of the stud with an
awl or thin nail or use an edge to edge stud nder.
CAUTION: Avoid potential personal injuries
and property damage!
Any material covering the wall must not
exceed 16 mm (5/8 in.).
Minimum wood stud size: common 2 x 4 in
(nominal 1½ x 3½ in).
Mark the locations for the rst lag
bolts on the center line of the stud
measuring 578.4 mm (23⁄ in.)
apart for the CFR1615 and 809.6
mm (31⁄ in.) for the CFR1620.
CFR1615
578.4 mm
(23⁄ in.)
CFR1620
809.6 mm
(31⁄ in.)
41 cm
(16 in.)
Mounting to Wall (Wood stud)

6
3 4 Start hinge side lag bolts [05]. Leave
approximately 13 mm (1/2 in.) of
space from the bolt head to the wall.
Drill pilot holes as illustrated.
CAUTION: Improper use
could reduce the holding power
of the lag bolt. To avoid potential
injuries or property damage:
pilot holes MUST be drilled to a
depth of 89 mm (3½ in.), using a
5.5 mm (7/32 in.) diameter drill
bit.
89 mm
(3½in.)
5.5 mm
(7/32 in.)
[05]
[05]
13mm
(1/2 in.)
13 mm
(1/2 in.)

7
5Hang swing arm/rack assembly onto the lag
bolts [05].
[05]
[05]
[01]
[01]

8
7Tighten lag bolts [05] only until the washers [06]
are pulled rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.)
[01]
[01]
[05] [06]
6Slip "U" washers [06] onto the lag bolts [05].
[01]
[01]
[05]
[05]
[06]
[06]

9
8 9 Tighten lag bolts [05] only until the washers [07]
are pulled rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.)
Drill through the top slots of the wall arms [01]
into the center of the next stud.
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage: pilot holes MUST be
drilled to a depth of 89 mm (3½ in.), using a 5.5
mm (7/32 in.) diameter drill bit.
89 mm
(3½in.)
[01]
[01]
[01]
[01]
[05]
[07]
5.5 mm
(7/32 in.)

10
1 2
406.6 mm
(16 in.)
CFR1615
578.4 mm
(23⁄ in.)
CFR1620
809.6 mm
(31⁄ in.)
Mark the locations for the lag bolts on the
corners of a rectangle measuring 406.4 (16 in.)
wide and 578.4 mm (23⁄ in.) for the CFR1615
and 809.6 mm (31⁄ in.) for the CFR1620 tall.
Drill pilot holes as illustrated.
CAUTION: To avoid potential injuries or
property damage:
Pilot holes MUST be drilled to adepth of 89 mm
(3½ in.) using a 10 mm (3/8 in.) diameter drill bit.
Never drill into the mortar between blocks.
Minimum solid concrete thickness: 8 in.
Minimum concrete block size: 8 x 8 x 16 in.
89 mm
(3½in.)
10 mm
(3/8 in.)
Mount to Wall (solid concrete or concrete block)