Satco STARFISH S11267 User manual

START HERE
In-Wall Wi-Fi
Switch
S11267
Installation Guide
WIFI
2.4GHz
NO HUB NEEDED

This switch is rated for
Incandescent, CFL, LED
and resistive loads
as well as motors
120VAC 60HZ
6A (720W) INC, CFL, LED,
Resistive, 3.6A Motor
NOTE: A NEUTRAL WIRE IS
REQUIRED FOR INSTALLATION
No Derating is required
when installing in
multi-gang applications.

WARNING:
This product may represent a
possible shock or re hazard if
improperly installed or attached in
any way. Product should be installed
in accordance with the owner’s
manual, current electrical codes
and/or the current National Electric
Code (NEC).
CAUTION: RISK OF
ELECTRIC SHOCK.
- TURN OFF THE MAIN POWER AT
THE CIRCUIT BREAKER BEFORE
INSTALLING.
CAUTION: RISK OF FIRE.
- FOR CONTROL OF
INCANDESCENT, CFL, LED
AND RESISTIVE LOADS
AS WELL AS MOTORS
- DO NOT USE WITH
CONTROL RECEPTACLE
OUTLETS,FLUORESCENT
LIGHTING FIXTURES,
- DO NOT EXCEED
ELECTRICAL RATINGS.
- USE INDOORS ONLY.
- SHALL INSTALL IN A METALLIC
OUTLET BOX HAVING MIN. WIDTH
50MM, OR A NON-METALLIC BOX.
- ONLY USE WITH SOLID COPPER
WIRE OR COPPER-CLAD WIRE.
CAUTION:
- INSTALLATION REQUIRES A
NEUTRAL WIRE.
- THIS DEVICE DOES NOT WORK
WITH SMART LAMPS.
REPLACING LIGHT BULBS.
- Make sure switches are in OFF
position (no light level indicator
lights are lit)
- To ensure there is no power at the
socket when replacing light bulbs,
turn off power at circuit breaker
or fuse.
FCC/IC INFORMATION
This device complies with part 15 of
the FCC Rules and Industry Canada
license-exempt RSS standard(s).
Operation is subject to the following
two conditions: (1) This device may
not cause interference, and (2) this
device must accept any interference,
including interference that may cause
undesired operation.
Note: This equipment has been
tested and found to comply with the
limits for a Class B digital device,
pursuant to part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment
generates, uses, and can radiate
radio frequency energy and, if not
installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications.
However, there is no guarantee
that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving
antenna.
- Increase the separation between
the equipment and receiver.
- Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an
experienced radio/TV technician
for help.

1) Power Indicator &
Conguration Light
2) On/Off Switch
OPERATION

Wall plate
(x1)
Inner frame
screws
(x2)
Mounting
screws
(pre-installed)
(x2)
Mounting
frame (x1)
Smart
switch (x1)
PARTS INCLUDED

Verify that a neutral wire is available prior to installation
How do I know if I have a neutral wire?
1. Turn power off at your breaker box and ensure the power is off
2. Remove the wall plate and existing device from the wall box
3. Remove and straighten all wires from the device
4. If you see a white wire (or bundle of them), it is likely that you have a
neutral in that switch box
5. If you do not have a neutral wire, this switch WILL NOT work
If this looks different from your wallbox, please consult a certied electrician

SWITCH INSTALLATION
WARNING: SHOCK HAZARD.
May result in serious injury or death.
Turn off power at circuit breaker or fuse
and test that power is off before wiring.
Turn power OFF at the circuit breaker
and ensure power is off.
CONTINUED ON OTHER SIDE

Identify if your wiring is
SINGLE POLE or 3-WAY
SINGLE POLE:
control from a single location
3-WAY:
control from 2 locations

You will need to determine which is the
“LINE” wire and wall box and which is the
“LOAD” wire and wall box.
Your old switch may have a screw
terminal of a different color (usually black).
This will either be the “LINE” connection
or the “LOAD” connection. Tag this wire
with a piece of electrical tape.
Disconnect all wires from the old switch
and ensure no wires are touching. Turn
the power back on at the circuit breaker.
Use a handheld voltage tester to
determine if the tagged wire is “live”.
If the tagged wire is “live”, this is the
“LINE” wire and wall box. If not, this
is the “LOAD” wire (and wall box in
3-way applications).

Preparing and connecting wires:
Use with #12-14 AWG solid copper or
copper-clad wire. Strip wires to 2 cm
(.8 inch).
NOTE: Ensure power is off before
preforming this step!
Insert wires into terminal holes and
secure connections by tightening
terminal screws to 16 lbf-in
(1.8 N.M) as shown.

SINGLE POLE WIRING
Ensure that the following
connections are made:
“LINE” wire
to the terminal marked AC-L
“LOAD” wire
to the terminal marked LOAD
Neutral wire
to the terminal marked AC-N
Ground wire
to the terminal marked GND

3-WAY WIRING
Note: A single pole or
3-way switch can be
used alongside the
smart switch.
IMPORTANT: The
switch must be
installed in the “LINE”
wall box and the
smart switch must
be installed in the
“LOAD” wall box.
Ensure that the following
connections are made
at the smart switch:
“LINE” wire
to the AC-L terminal
“LOAD” wire
to the LOAD terminal
Traveler wire
to the YL/RD terminal
Neutral wire
to the AC-N terminal
Ground wire
to the GND terminal
Ensure that the following
connections are made
at the switch:
“LINE” wire
to one terminal
Traveler wire
to the other terminal
Ground wire
to the GND terminal

MOUNTING
Push wires into the wall box and push
switch into opening
Mount the switch into wall box and
install the wall plate
TESTING
Turn power back on at the
circuit breaker
Test the device to ensure that the
lights will turn on and off

DOWNLOAD THE FREE
“STARFISH SMART
LIGHTING” APP
Please refer to our
Starsh user guide for
detailed instructions on
how to pair your device
TROUBLESHOOTING
Lights are ickering:
-Lamp has a bad connection.
- The switch wire connections are not
rmly secured.
Light does not turn ON:
- Circuit breaker or fuse has tripped.
- Bulb or lamp is burned out.
Power indicator light does not turn ON:
- Neutral is not connected to switch
(white wire)
- Conrm that switch is being supplied
from a 120V AC,60Hz source ONLY.
Intermittent switch operation:
- Conrm that the LOAD being controlled
does not exceed 6A (720W) INC, CFL,
LED, Resistive 3.6A Motor

ENJOY THESE OTHER GREAT STARFISH WIFI SMART LED PRODUCTS
͵ 






Technical Support www.satco.com/Starsh

:
,.
·• 0 ✓
• 0 •
• •
••o •. o .- o••
ooo oo o
··• o •• ·
•.• 0 •. ,.
0 • 0
0 • 0
0 : 0
• • •
• •
STARFISH™
live Ufe eri ti ghtened
0 DOWNLOAD
THE
STARFISH
APP
I .
• App Store
► Google Play
Sy stem Requirements
Minimum iOS9.3 or Android 4.4
• Dedicated 2. 4GHz Wifi Network •
~ ~
TECHNICAL SUPPORT
www.satco.com/Starfish

a
II
Launch the App and tap u Reglster " for new accounts
or " Login " for ex i sting accounts .
Enter E- M ail address , then tap M Get verification code "
.., _.,.
......
<
II Create a Password then tap " Done "
<
SetPelaword
...... .,,t M•.ai-•- 19'-1..,t I

a
Create/Share
a Home
Create a Home
Tap the " Me " button on the bottom of the screen,
and then tap " Home Manag ement" . Tap the "Create
a home" button to setup your home .
Q ........._
ea ..
- -
Q .....
-
IATCD ~
- u,t _, l C S,.,\, I
-- ·
.J ....
•
---
_, .

Share a Home
II From the Home Management screen , select the Home
that you would like to share .
D
Tap " Add Member " and select the way that you would
like to send the Invitation •
• 1WVMU I
( HorttieMa,og :ad
Enter the user information and select if the new member
will be an '' Adn1inistrator " or a" Common Member " in
the Home. Tap " Save " to send the invitation
--
MdUtt: ba
•

Add Devices
II Tap the plus(+) button on the upper right hand comer
to add a device
--
AIDI
El Make sure you are connected to a 2.4GHz WIFi
Network then manually add smart llghtlng devices
<
'.
•
-
....
.. ,..,
...
-
....
,_.
• •