Satel SPP-100 User manual

FIRE ALARM SOUNDER
SPP-100
SPP-101
Installation Manual
spp-100_en 07/13
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. [phone]
[email protected]
www.satel.eu

The SPP-100 / SPP-101 fire alarm sounder meets the essential requirements of the
European Union Directives:
CPD 89/106/EEC Construction Products Directive;
EMC 2004/108/EC Electromagnetic Compatibility Directive;
An EC Certificate of Conformity No. 1438/CPD/0343 was issued by the CNBOP-PIB Jozefow
Certification Body for the SPP-100 / SPP-101 fire alarm sounder to confirm its compliance
with the requirements of PN-EN 54-3:2003 + PN-EN 54-3:2003/A2:2007 standards.
The Certificate of Conformity can be downloaded from the www.satel.eu website.
14
38
SATEL Sp. z o.o. • ul. Franciszka Schuberta 79 • 80-172 Gdańsk • POLAND
13
1438/CPD/0343
EN 54-3
Fire alarm sounder SPP-100 (type A), SPP-101 (type B)
Application – fire safety.
Technical specifications – please refer to this manual.

This manual covers the following products:
SPP-100 - fire alarm sounder with a low base (Fig. 1);
SPP-101 - fire alarm sounder with a high base (Fig. 2).
The fire alarm sounders provide information about fire by means of acoustic signals. They
are designed to be used in conjunction with the CSP-104, CSP-108, CSP-204 and CSP-208
fire alarm control panels.
Prior to installation, please read this manual carefully in order to avoid any mistakes and/or
errors which might result in malfunctioning of or even damage to the equipment. The manual
contains guidelines for installation of the fire alarm sounders and their connection to the fire
alarm control panel.
63 mm
91 mm
1. Features
Acoustic signaling by means of piezoelectric transducer.
32 selectable tones.
Selectable volume level.
2. Functional description
After voltage is applied to the appropriate terminals, acoustic signaling will be activated. The
tone depends on the settings of DIP-switches.

2 SPP-100 ●SPP-101 SATEL
3. Installation
Disconnect power before making any electrical connections.
1. Run the cables into the enclosure base. For the SPP-100 sounders, you can make
additional holes in the enclosure (Fig. 3). In the case of SPP-101 sounders, you must
make holes for the cable glands (Fig. 4).
3
2. Secure the enclosure base to the wall.
3. Set the volume and select the tone (see section S
ELECTING THE TONE AND SETTING THE
VOLUME
).
4. Screw the wires to the corresponding terminals. Fig. 5 shows a typical connection of the
fire alarm sounders to the fire alarm control panel.
5. Replace the enclosure cover and secure it with the lock screw.

SATEL SPP-100 ●SPP-101 3
3.1 Selecting the tone and setting the volume
6
123 45
ON
V
OL
To select the tone to be triggered after voltage is applied, use the DIP-switches, designated
by digits from 1 to 5 (see Fig. 6). The tones and the way of setting the DIP-switches are
described in the table below (DIP-switch in position ON = 1).
The DIP-switch designated VOL is used to set the signal volume level. When the switch is in
the ON position, the maximum volume of signaling is set (the recommended setting).
For detailed information about the sound intensity (volume) in accordance with EN54-3,
please refer to SPP-100-spl.

4 SPP-100 ●SPP-101 SATEL

SATEL SPP-100 ●SPP-101 5
4. Maintenance
The fire alarm sounders should be subject to regular checks to ensure they are working
correctly. Periodic checks should be conducted at least every six months.
5. Specifications
Supply voltage .......................................................................................................18...28 V DC
Standby current consumption ............................................................................................0 mA
Maximum current consumption........................................................................................32 mA
Operating temperature range..................................................................................-25...+70 °C
Maximum humidity..........................................................................................................93±3%
Protection rating SPP -100..........................................................................IP54
SPP -101..........................................................................IP65
Enclosure dimensions SPP-100........................................................93 x 93 x 63 mm
SPP-101........................................................93 x 93 x 91 mm
Weight SPP-100......................................................................... 174 g
SPP-101......................................................................... 206 g