Satel SPP-400 User manual

Addressable fire alarm sounder
SPP-400
Firmware version 1.00
spp-400_en 02/23
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.pl
EN

IMPORTANT
The device should be installed by qualified personnel.
Prior to installation, please read carefully this manual in order to avoid mistakes that can lead
to malfunction or even damage to the equipment.
Disconnect power before making any electrical connections.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
The following symbols may be used in this manual:
- note,
- caution.

The SPP-400 indoor sounder is used for acoustic alarm signaling. It is designed to operate in
the detection line of the ACSP-402 addressable fire alarm control panel.
1. Features
Acoustic signaling by means of piezoelectric transducer.
Signaling controlled by the control panel:
–different tones for different alarm conditions.
–32 selectable tones.
Double-sided short-circuit isolator.
Power supply from the detection line.
2. Installation
Disconnect power before making any electrical connections.
The sounder is designed for installation indoors, in spaces with normal air humidity.
1. Turn the cover counter-clockwise and remove it (Fig. 1).
2. Drill the holes for screws in the enclosure base. Use the countersunk screws (Fig. 2) or
the non-countersunk screws (Fig. 3) to fasten the enclosure base to the wall.
3. Drill the hole for cables in the enclosure base (Fig. 4).
4. Place the enclosure base against the wall and mark the location of mounting holes.
5. Drill the holes for wall plugs (screw anchors) in the wall.
6. Run the cables inside the enclosure base.
7. Use wall plugs and screws to secure the enclosure base to the wall. Select wall plugs
specifically intended for the mounting surface (different for concrete or brick wall, different
for plaster wall, etc.).

2 SPP-400 SATEL
8. Connect the detection line wires to the sounder (Fig. 5 –loop; Fig. 6 –radial circuit).
To terminals A+ and A-, connect the wires from the control panel / previous device.
Connect the wires to terminals B+ and B- to connect the sounder to the next device /
control panel. For radial circuits, if the sounder is the last device in the circuit, do not

SATEL SPP-400 3
connect the wires to terminals B+ and B- (Fig. 6). Connect the cable shields to the E /
terminals.
9. Replace the cover and turn it clockwise (Fig. 7).
10.Lock the cover with a screw (Fig. 8).

4 SPP-400 SATEL
3. Acoustic signaling
Configure the acoustic signaling settings in the control panel. For each alarm condition you
can select one of the 32 available tones (see: Table 1).

SATEL SPP-400 5
No
Acoustic signaling
Frequency Hz
Description
1
800 & 970
2 Hz (250 ms –250 ms)
2
800-970
7 Hz (7/s)
3
800-970
1 Hz (1/s)
4
2850
Continuous
5
2400-2850
7 Hz
6
2400-2850
1 Hz
7
500-1200
3 s sound, 0.5 s silence, repeated
8
1200-500
1 Hz
9
2400-2850
2 Hz (250 ms –250 ms)
10
970
0.5 Hz (1 s)
11
800 & 970
1 Hz (500 ms –500 ms)
12
2850
0.5 Hz (1 s)
13
970
0.8 Hz (250 ms / 1 s)
14
970
Continuous
15
554 & 440
100 ms –400 ms
16
660
3.3 Hz (150 ms)
17
660
0.28 Hz (1.8 s)
18
660
0.05 Hz (13 s / 6.5 Hz)
19
660
Continuous
20
554 & 440
0.5 Hz (1 s)
21
660
1 Hz (500 ms –500 ms)
22
2850
4 Hz (150 ms –100 ms)
23
800-970
50 Hz
24
2400-2850
50 Hz
25
970
3 x 500 ms sound, 1.5 s silence, repeated
26
800-970
3 x 500 ms sound, 1.5 s silence, repeated
27
970 & 800
3 x 500 ms sound, 1.5 s silence, repeated
28
2400
Continuous
29
990 & 650
2 Hz (250 ms –250 ms) (Symphoni Tones)
30
510 & 610
2 Hz (250 ms –250 ms) (Squashni Micro Tones)
31
300-1200
1 Hz
32
510 & 610
1 Hz (500 ms –500 ms)
Table 1.
Tone / supply voltage
Angle-dependent [°] minimum sound level [dBA]
15°
45°
75°
105°
135°
165°
1 / 18 VDC
81.1
87.2
91.5
91.9
87.1
80.7
1 / 26 VDC
82.9
88.9
94.4
94.6
91.5
84.1
2 / 18 VDC
79.3
86.9
90.5
90.2
85.4
78.4
2 / 26 VDC
82.1
88.8
92.9
93.0
89.3
81.1
3 / 18 VDC
80.2
88.0
91.7
91.8
86.3
79.5
3 / 26 VDC
82.5
89.3
93.9
94.1
89.9
81.6
4 / 18 VDC
71.8
82.7
85.0
84.1
82.1
72.1
4 / 26 VDC
71.0
81.5
83.6
85.3
83.1
71.6
5 / 18 VDC
76.1
85.3
86.6
86.0
83.2
74.6

6 SPP-400 SATEL
Tone / supply voltage
Angle-dependent [°] minimum sound level [dBA]
15°
45°
75°
105°
135°
165°
5 / 26 VDC
76.2
84.6
86.5
87.1
84.9
76.0
6 / 18 VDC
78.0
86.7
88.0
86.8
85.1
75.8
6 / 26 VDC
77.5
85.5
86.7
87.4
85.4
77.0
7 / 18 VDC
80.1
87.5
91.7
91.8
86.1
80.4
7 / 26 VDC
83.8
88.9
94.5
94.8
90.8
83.3
8 / 18 VDC
79.7
87.0
90.9
90.9
85.4
79.1
8 / 26 VDC
82.4
88.5
93.4
93.6
89.5
82.3
9 / 18 VDC
75.9
81.6
86.9
86.2
80.6
74.7
9 / 26 VDC
76.0
81.6
86.1
87.3
83.0
76.2
10 / 18 VDC
79.9
87.2
91.6
91.8
87.5
81.1
10 / 26 VDC
83.9
88.7
94.5
94.4
91.4
83.6
11 / 18 VDC
79.8
87.3
91.9
92.1
87.5
80.4
11 / 26 VDC
82.9
88.5
93.8
94.1
90.7
83.3
12 / 18 VDC
71.4
83.9
86.7
85.8
83.5
72.7
12 / 26 VDC
75.8
86.2
88.6
89.6
87.9
76.1
13 / 18 VDC
79.3
86.9
91.5
91.7
87.1
80.1
13 / 26 VDC
83.3
88.7
94.1
94.8
91.0
83.6
14 / 18 VDC
79.4
86.9
91.4
91.6
87.3
80.8
14 / 26 VDC
81.7
88.1
93.2
93.4
90.3
82.5
15 / 18 VDC
77.2
84.2
87.2
87.1
82.3
77.1
15 / 26 VDC
78.3
84.8
88.6
88.7
84.9
78.6
16 / 18 VDC
76.6
85.6
87.9
87.7
84.0
75.2
16 / 26 VDC
81.0
86.6
91.1
91.5
87.7
80.8
17 / 18 VDC
78.0
86.9
89.3
89.3
84.8
78.0
17 / 26 VDC
82.2
87.9
92.5
92.7
88.8
82.1
18 / 18 VDC
77.9
86.8
89.1
88.9
85.1
77.3
18 / 26 VDC
88.2
87.7
92.2
92.6
88.8
81.9
19 / 18 VDC
78.0
87.0
89.3
89.2
84.8
77.2
19 / 26 VDC
82.3
87.9
92.4
92.8
88.8
82.1
20 / 18 VDC
77.0
84.0
87.6
87.4
82.7
77.5
20 / 26 VDC
78.3
84.6
88.3
88.7
84.9
78.4
21 / 18 VDC
77.8
87.1
89.2
89.1
84.7
77.0
21 / 26 VDC
82.2
88.0
92.5
92.7
88.9
82.1
22 / 18 VDC
72.5
84.6
87.7
86.6
84.4
73.7
22 / 26 VDC
74.9
85.4
87.5
88.3
86.7
75.1
23 / 18 VDC
79.1
86.5
89.8
89.6
84.6
78.1
23 / 26 VDC
81.8
88.4
92.5
92.6
89.1
81.1
24 / 18 VDC
75.7
84.0
86.5
85.6
82.8
74.1
24 / 26 VDC
75.9
84.3
86.1
86.6
84.3
75.7
25 / 18 VDC
79.9
87.4
92.0
92.1
87.5
80.9
25 / 26 VDC
82.7
88.8
94.2
94.9
91.8
84.3
26 / 18 VDC
80.0
86.9
91.1
90.8
85.5
78.6
26 / 26 VDC
82.8
88.6
94.0
93.9
89.6
81.6
27 / 18 VDC
79.4
86.9
91.5
91.7
87.1
80.1
27 / 26 VDC
82.4
88.5
94.0
94.8
91.6
84.1

SATEL SPP-400 7
Tone / supply voltage
Angle-dependent [°] minimum sound level [dBA]
15°
45°
75°
105°
135°
165°
28 / 18 VDC
75.7
79.5
86.9
86.0
78.8
74.6
28 / 26 VDC
76.4
80.3
85.9
87.1
80.5
76.4
29 / 18 VDC
78.9
87.5
90.9
90.8
85.4
79.5
29 / 26 VDC
84.0
88.4
94.1
94.5
90.2
84.1
30 / 18 VDC
77.2
85.5
89.0
88.9
83.6
77.1
30 / 26 VDC
80.7
88.4
92.3
92.0
87.9
79.9
31 / 18 VDC
78.9
86.4
90.1
90.2
84.9
78.8
31 / 26 VDC
79.8
86.5
91.7
91.8
87.9
80.5
32 / 18 VDC
77.1
85.5
89.0
89.0
83.7
77.3
32 / 26 VDC
80.7
88.3
92.2
91.9
87.8
79.8
Table 2.
4. Maintenance
The fire alarm system elements require regular maintenance. The periodic checks of the
SPP-400 sounder should be carried out at least every 6 months. In spaces where working
conditions are difficult (e.g. dust, aggressive environment that may cause corrosion, etc.), the
periodic checks should be carried out more often.
As part of maintenance, start a test in the control panel and make sure the acoustic signaling
is working. Please go to the ACSP-402 control panel manuals to find out how to start the test.
Start of the test and test activation of devices will be registered in the control panel event log.
During the test, make sure the device is in its right place (e.g. it has not been swapped with
another device).
5. Specifications
Supply voltage........................................................................................................18...26 VDC
Quiescent current consumption....................................................................................0.25 mA
Alarm current consumption................................................................................................4 mA
Operating temperature range...............................................................................-10°C...+55°C
Maximum humidity..............................................................................................................95%
Protection rating...............................................................................................................IP21C
Operating environment type.....................................................................................................A
Dimensions..................................................................................................108 x 108 x 87 mm
Weight...............................................................................................................................224 g

8 SPP-400 SATEL
The SPP-400 fire alarm sounder conforms to the essential requirements of the EU
Regulations and Directives:
CPR 305/2011 Regulation of the European Parliament and of the Council of 9 March 2011
laying down harmonized conditions for the marketing of construction products and repealing
the Council Directive 89/106/EEC on construction products;
EMC 2014/30/UE Electromagnetic Compatibility Directive;
LVD 2014/35/EU Low Voltage Directive.
The CNBOP-PIB Certification Body in Józefów issued the Certificate of Constancy of
Performance 1438-CPR-0859 for the construction product SPP-400 fire alarm sounder,
confirming its compliance with the requirements of EN 54-3:2003+A1:2002+A2:2006 and
EN 54-17:2005 + AC:2007.
The Certificate and the Declaration of Performance can be downloaded from the
www.satel.pl website.
The SPP-400 fire alarm sounder has been granted the Certificate of Admittance
No 4768/2022 by the CNBOP-PIB in Józefów.
The Certificate of Admittance can be downloaded from the www.satel.pl website.
23
SATEL Sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
1438
1438-CPR-0859
Declaration of Performance DOP/CPR/0859
EN 54 3:2003+A1:2002+A2:2006
EN 54-17:2005 + AC:2007
Fire safety.
SPP-400 fire alarm sounder (type A).
Use –see the Declaration of Performance DOP/CPR/0859.
Technical specifications –see this manual.