Saturn 2000 User manual

Saturn 2000
Mobile Power Station
AC 2000W Fast Charge Type-C PD 100W Power Multiple Devices
Instruction Manual
ART.55705

2
Introduction
Thank you for choosing our product. For safe and efficient use of this equipment, please keep
this User Manual properly and read it carefully before use. After unpacking, please check the
product carefully. Check the items against the Packing List. In case of any inconsistency,
please contact your local dealer.
The relevent design schemes and manufacturing technology used in this product are
protected by patents.
The contents are subject to change without notice.

3
1. Safety Tips and Precautions………………………………………….4
2. Product Introduction.…………………………………………………..5
2.1 Appearance.…………………………………………………………5
2.2 Technical Parameters……………………………………………..8
3. Instructions for Use…………………………………………………….9
3.1 Battery Level Checking…………………………………………...9
3.2 Charging Mode …..………………………………………………...9
3.3 Solar Controller……………………………………………………10
3.4 Lighting Function…………………………………………………12
3.5 USB/12V DC Output Port …….………………………………….12
3.6 AC Output…………………………….…………………………….12
3.7 Protection Status Indication…………………………………….13
4. Common Failures and Countermeasures ………………………..14
5. Maintenance,Storage and Scrapping……………………………...14
5.1 Maintenance ………………………………………………………14
5.2 Storage …………………………………………………………….14
5.3 Scrapping ………………………………………………………....14
6. After-sales Service .…………………………………………………..15
7. Packing List…………………………………………………………….15
8. Warranty Time.…………………………………………………..........15
9. Warranty Range.…………………………………………………........16
10. Disclaimer.…………………………………………………...............16
11. Precautions.………………………………………………….............16
12. Product Warranty.…………………………………………………....17

4
Note:
If the equipment needs maintenance and repair, we recommend users to contact the
nearest authorized unit of factory. If the user delivers the equipment to an unauthorized
service center for maintenance or repair, the user is no longer entitled to the manufacturer's
warranty service.
Safety Tips and Precautions
1.1 Install the grounding device correctly according to the application stan-
dard.
1.2 Please use the product in a clean and dry environment to ensure the
working position is safe.
1.3 There shall be no flammables or explosives in the working space.
1.4 Workers implanted with cardiac pacemaker shall consult the doctor be-
fore using the equipment.
1.5 The product shall not be dumped or used upside down.
1.6 The built-in battery of the equipment shall be used under the environ-
ment specified in this Manual.
1.7 Avoid violent vibration and collision since the equipment contains lithium
battery.
1.8 Do not store the equipment with other items. There shall be no heavy ob-
jects on top of it.
1.9 Do not disassemble the equipment by yourself in case of failure.
1.10 Keep away from high temperature objects such as fire sources.
1.11 Avoid rainwater from seeping into the equipment.
1.12 Do not cover the machine, do not affect the ventilation and heat dissipa-
tion when it is working.

5
SN.
P1
P2
P3
P4
P5
P6
P7
P8
P9
K1
K2
K3
Function
Connect the charger
Dual 5V 2.4A output
MAX 65W output
PD 100W output
DC 12V 10A output
DC 12V 10A output
AC 220V 2000W output
AC 220V 2000W output
On/Flashing/Off
Turn on/off the DC power
Turn on/off the light
Turn on/off the AC power/Long press
for five seconds to switch 50/60HZ
Name
Charging input port
USB output
USB QC output
USB Type-C port
12V Cigarette port
12V DC port
AC socket 1
AC socket 2
Lighting
DC button
LED button
AC button
Product Information
P7
P1
P5
P4
P3
P2
0520
OUTPU T
2000
INPUT
WATTS Hours WATTS
98 %
50Hz
60Hz
CAR
CAR 12V /10A
USB QC
USB-A U SB-A
TYPE- C
DC 12V/ 10A
P8
AC 1500W/3000W Peak
K1 P6 P9 K2 P9 K3

6
It is not displayed when the
machine is not connected to the
Internet, and displayed when the
device is connected to the Internet.
(Not available)
Rotating means the fan is on.
Used for engineering testing before
leaving the factory.
Display the current input power
level.
According to the power
consumption, the remaining
use/charging time is displayed, and
the battery lightning symbol lights
up to indicate how long it will take
to fully charge.
Indicates that the temperature of
the machine is too high, pay
attention to cooling down.
Indicates that the temperature of
the machine is too low, and it
should be moved to an environment
where the machine can work and
allowed to heat up naturally before
use.
Network connection
instructions
Cooling fan indication
Development mode
Input power
Remaining
charge/discharge time
High temperature
indication
Low temperature
indication
SN.
a
b
c
d
e
f
g
Icon Function Function

7
When this prompt appears, stop
using it immediately, follow the
instructions, or contact after-sales
service.
Display the current output power.
Display the remaining battery
power, 0~100%.
Indicate the remaining power, and
display the running light when
charging.
According to the use of the
machine, the combination shows
different states.
Displayed in combination with
different functional modules,
indicating the corresponding
module overload protection.
Car start function (not available)
UPS function (not available)
AC output, 50/60HZ
DC total output
DC 12V port output
USB-A port output
USB-C port output
Cigar lighter 12V output
Fault indication
Output power
Remaining battery
percentage
Battery level indicator
Atmosphere light
Overload indication
Function indication
h
i
j
k
l
m
n

8
Technical Parameters
Technical Specifications
Model
Battery Capacity
Battery Type
Wall Charging Time
Wall Charging Mode
Solar Charging Time
Solar Controller Mode
Charging Temperature Range
Life Cycles
USB Port
USB-QC Port
USB-Type-C Port
12V Cigarette Port
12V DC port
LED Light
Rated AC output
Peak AC output
Output Voltage
Output Frequency
Waveform
THD
Discharging Temperature Range
Weight
Dimension
Saturn 2000
1536Wh
LiFePO4
54V/10A About 3 hours
CC-CV
54V/7.5A MAX 3-4 hours
MPPT
0⁰C-45⁰C
2000 times
5V/2.4A * 2
Max 65W
PD 100W
12V/10A
12V/10A
2W * 2
2000W
4000W
220VAC ± 10%
50/60HZ
Pure sine wave
<3%
-10⁰C-60⁰C
21KG
394*223*320mm

9
Under the power off state, press the DC Button(K1) to observe the remaining battery
capacity through Battery percentage(j/k). It will shut down again if the Standby Button(K1)
is pressed again.
Please connect the charger correctly when the power of the device is low. The input power
(d) displays the charging power, the atmosphere light (l) displays cyclically, and the
remaining time (e) displays the remaining charging time.
After being fully charged, the battery percentage will display 100%, the atmosphere light (l)
will stop, and the LCD will turn off after 10 seconds and enter the standby mode.
Wall charger (54V 10A) takes about 3 hours to recharge.
Standard solar charger (54V 7.5A max) with 36V 400W solar panels takes 3-4 hours to
recharge depending on the solar conditions.
Recommend to solar panels above 100W, voltage 36V (16V-50V) with MC4 connector.
0520
OUTPU T
2000
INPUT
WATTS Hours WATTS
98 %
50Hz
60Hz
CAR
CAR 12V /10A
USB QC
USB-A U SB-A
TYPE- C
DC 12V/ 10A
AC 1500W/3000W Peak

10
Input
Output
Controller mode
MPPT efficiency
No load loss
Over voltage protection
Anti reverse connection protection
Working temperature
Weight
Size
3.3 Solar Controller
After the connection of the whole system is correct, if the sunlight is sufficient, the LED light
will flash several times and then the tube will light up, the controller will start to work, the
tube will display the system parameters in a cycle, and the LED light will indicate green
normally.
Status indication, as shown in the table below:
3.3.1 Controller Technical Specifications
3.3.2 Controller operation and status indication
Solar (solar indicator light)
Bat (output indicator)
( )
Fuse 15A
Battery (output line)
Charge Display
3.3.3 Output indication
16V〜50V/25A(MAX)
54V/7.5A(MAX)
MPPT
≥99%
< 5mA
58V±1.5V
-25℃ - 65℃
0.8Kg
L115×W111×H43(mm)
When the positive and negative poles of the battery
are connected reversely, the fuse will blow. The user
needs to replace the 15A, φ 5 × 20 glass tube fuse.
Show contents
The first digit of tube
Show contents
state
red
green
b
c
d
Status description
Solar panel access
Battery charging
Battery voltage
Solar panel input voltage
Solar panel charging current

11
3.3.4 Precautions
1) The controller can adapt to 18V and 36V solar panels, please do not use solar panels
with open circuit voltage higher than 50V, otherwise there is a risk of burning.
Please do not overload the controller. The maximum power of 18V solar panels is 200W.
If two 18V solar panels have a total power of more than 200W, please use them in se-
ries. The maximum power of 36V solar panels is 400W. If there are two or more solar
panels, please use them in parallel. (Solar panel parameter reference: 18V solar panel
working voltage is 18V, open circuit voltage is 22V; 36V solar panel working voltage is
36V, open circuit voltage is 44V. Please check the parameters on the back of the solar
panel carefully before connecting.)
2) The controller will generate heat during operation, so it is recommended to install it in a
ventilated and heat dissipation environment.
3) When using the system, it is recommended to connect the controller and the solar panel
first, and then connect the controller to the product equipment, otherwise the phenome-
non of ignition will appear when wiring.
4) The input and output of the system adopt isolation design, and do not share negative
pole, let alone positive pole.
5) There are no maintenance and repair parts in the controller, and the internal voltage is
higher than human safety. Please do not disassemble the controller by yourself.
6) Please do not put water or corrosive liquid into the controller, which will damage the con-
troller.
7) When operating, pay attention to use insulating tools and keep them dry.

12
3.4 Lighting function
Press the lighting button (K2), the illumination LED (P9) lights up; Press the lighting button
(K2) again, the illumination LED (P9) turns up lighter; Press the lighting button (K2) for the
3rd time, the illumination LED (P9) turns off; Press the lighting button (K2) stay 2S, the
illumination LED (P9) SOS flashes; Press the lighting button (K2) again, the illumination
LED (P9) turns off, and it can be cycled.
3.5 USB/12V DC Output Port
( )
Under the power off state, press the DC Button K1 , screen displays the power of the
power device in real time (if the load power is less than 1W, it cannot be displayed), press
the DC Button again, USB /12V DC Output Port is off.
If the load power is less than 1W, the DC module will shut down automatically in 24 hours.
3.6 AC Output
Press the power button (K3), the AC turns on and starts the internal inverter. After the AC
indicator (n) lights up, the AC sockets output the rated AC voltage. If no load or load power
less than 10W, the AC module will automatically shut down in 12 hours.
AC 1500W/3000W Peak
CAR 12V/10A
USB QC
USB-A USB-A
TYPE-C
DC 12V/10A
Note:
Before power on the AC power, make sure that the appliance is not short circuited.
When starting up, first press the AC button (K3) to turn it on, then turn on the external
electrical equipment.
When shutting down, first turn off the external electrical equipment, then press the AC
Button (K3) to turn it off.

3.7 Protection Status Indication
List of Normal Protection Status of Control Panel
13
The battery icon flashes, indicating
that the battery is exhausted.
Please charge the machine in
time.
The constant light indicates that
the battery is charged at a high
temperature, and the machine will
automatically charge after cooling
down; The flashing indicates that
the battery is discharged at a high
temperature, please cool down
before use.
Constant light indicates that the
battery is charged at a low
temperature, and the machine will
automatically charge after heating
up; Flashing indicates that the
battery is discharged at a low
temperature, please warm up the
machine before using it.
DC and overload icons flash
together, please remove the DC
load, the machine will
automatically recover.
DC and high temperature icons
flash together, please remove the
DC load, turn off the DC function
and wait for a while before using it
again.
AC and overload icons flash
together, please remove the AC
load and restart it to recover.
The Error icon flashes and
displays E01~E16. Try to shut
down and restart. If it still fails to
recover, please contact after-sales
service.
Low Battery
High Battery
Temperature
Low Battery
Temperature
DC Overload
Protection
DC Over
Temperature
Protection
AC Overload
Protection
System Error
Display Status Measures
EXX

For other non-common failures, if multiple restarts cannot be recovered, please contact
your local dealer or authorized service point.
14
Check if the electrical equipment is connected reliably.
Check if the high temperature indicator is flashing.
Shut down and wait for 60S and restart.
Check whether the charging cable is connected properly.
Check whether any temperature prompt is given.
No AC output
The battery is not fully
charged even after more
than 12 hours of charging
Common failures Measures
5.1 Maintenance
5.1.1 After use, remove the plug before performing maintenance.
5.1.2 Use a piece of dry cloth to remove the dust and oil stains on the wires and casing.
5.1.3 Do not disassemble the equipment. There are no parts that may be repaired by users,
and all repair services shall be provided by qualified maintenance personnel.
5.2 Storage
5.2.1 Before long-term storage, the equipment shall be fully charged, that is, the power
indicator fully lights up.
5.2.2 Storage environment: temperature around 25°C, dry and ventilated.
5.2.3 Do not completely discharge the battery.
5.2.4 It is recommended to fully charge the product after each use.
5.2.5 When it is not frequently used, charge it at least once every 3 months to avoid
excessive discharge.
5.3 Scrapping
For the scrapping of this product, please refer to the regulations of the specific country
or region on lithium battery scrapping and recycling.
Maintenance,Storage and Scrapping

Please keep the warranty card properly. This product is guaranteed for one year,
calculating from the date of purchase. For any question, please contact your local
dealer or call our service department.
For failure caused by defects in materials or workmanship, local dealer or authorized
service point will provide free maintenance service for one year from the date of
shipment. This warranty does not cover failures caused by normal wear or misuse. For
further details on warranty coverage and warranty information, please contact the
After-sales Service of the company.
15
1
1
1
1
Mobile power generator
Wall charger
Solar power controller
Manual
Name Specification Quantity
Saturn 2000
54V/10A
54V/7.5A MAX
English
The product warranty is valid for one year from the date of shipment of the product (the
shipping fee after initial failure is borne by the customer).
★The initial failure period is one month from the date of product shipment.
★Be sure to keep the main unit, accessories, and instruction manual (warranty card).
★Repair may take some time depending on the content of the problem.
★If repair is not possible, we will replace it, but if it is out of stock, you may have to wait
until the next arrival.
★For repairs, please fill in the required items on the warranty card and enclose it. If the
warranty card is not enclosed, the warranty will be void.
Warranty Time

The product warranty policy promises to repair defective parts of this product and
replace it free of charge.
The Company shall not be liable for any accidents or damages caused by the failure of
this product or its use.
Disclaimer
The warranty is valid only for items that we have officially sold and handled.
The nominal value depends on the usage conditions and is not covered by the warranty.
If repair parts or replacement parts are out of stock, you may have to wait until the next
arrival date.
This warranty is subject to change without notice.
Precautions
The warranty of this product is to provide repair (replacement) in the event of a failure
despite normal use.
★Even within the warranty period, if any of the following items apply, it will not be applicable.
★Failure or damage caused by incorrect use or improper repair or modification.
★Failure or damage caused by transportation, movement, dropping, etc.
★Damage caused by external factors such as fire, earthquake, flood, lightning strike,
and other natural disasters.
★Wear due to use, deterioration over time, etc.
★If the product itself, warranty card, accessories, etc. are missing.
★If we cannot specify the sale date because the warranty card is not enclosed or the
order number is unknown.
★Dirt, scratches, dents, etc. that do not cause any problems in use.
★Purchases other than authorized retailers, such as individual sales, resale, second-
hand sales, etc.
★Failure due to misuse by the customer or usage environment (high temperature and
humidity, place with a lot of dust / dust, etc.).
Warranty Range
16

This manual promises to repair the product free of charge according to the contents of the
"Warranty Policy" in the event of a failure during the following period from the date of
purchase.
Please note that the personal information you provide may be used for repairs within the
warranty period and for subsequent safety inspection activities.
Product warranty
17

18

19