Savant SVR-SMRTD-10 User manual

Box Contents
(1) Savant® Smart Host (SVR-SMRTD-10)
(1) 12V DC 3A Power Supply
with 4 Quick Change AC Adapters (025-0146-xx)
(1) Vesa Pattern Mounting Bracket with screws
(75 mm and 100 mm)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Environmental
Temperature
32°F to +104°F (0°C to 40°C)
Humidity
10% to 90% Relative Humidity (non-
condensing)
Cooling
10 CFM
Maximum BTU
61.5 BTU/hr
Dimensions and Weight
Dimensions and Weight
Height
1.57 in (40 mm)
Width
7.48 in (190 mm)
Depth
4.56 in (116 mm)
Weight (Shipping)
6 lb (2.72 kg)
Rack Space
1U
Power
Power
Power Supply
12V DC 3A
Compliance
Compliance
Safety and
Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
Minimum Supported Release:
Minimum Supported Release:
Savant OS
da Vinci 7.0
Front Panel
Power Button
Use to power the SVR On or Off.
White indicates the unit is powered on.
HDD LED
This LED is has no function. Flash Memory
is used in place of a Hard Disk Drive.
Rear Panel
Power Input
12V DC 3A - Connect to included power
supply.
Ethernet
10/100/1000 Base-T auto-negotiating port
with Link/Activity LEDs.
See items C and D for LED functionality.
Data Rate LED
Off:10 Mbps data rate
Green: 100 Mbps data rate
Yellow: 1000 Mbps data rate
Link LED
Off: Ethernet link is not established.
Green Solid: Ethernet link is established.
Green Blinking: Ethernet activity is
occurring.
Audio Out
Use for Audio Interrupt Service (AIS) with
Savant controllers with an Analog Audio
Input.
3.5 mm (1/8 in) Stereo jack.
Note:
Connections not identified in the diagrams above are not functional
within a Savant Configuration/Installation.
SVR-SMRTD-10 | 009-1265-02 | 150223
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
1 of 2
savant.com | 508.683.2500
Savant® Smart Host
Quick Reference Guide
For Product Info

Network Requirements
Savant requires the use of business class/commercial grade network
equipment throughout the network to ensure the reliability of
communication between devices. These higher quality components
also allow for more accurate troubleshooting when needed.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power
outage, a static IP Address or DHCP reservation should be
configured. Savant recommends using DHCP reservation within the
router. By using this method, static IP Addresses for all devices can
be managed from a single UI avoiding the need to access devices
individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Network Changes
After connecting to a new network, changing routers, or if the IP
Address range is changed in the current router, Savant recommends
the following steps to refresh any IP connection and ensure that the
Smart Host is communicating with the network correctly.
To refresh the IP connection, perform one of the following steps:
•Cycle Power
1. Press the Power button to power Offthe Smart Host.
2. After 10 seconds, verify that the Power LED is not illuminated
indicating that shutdown has completed.
3. Press the Power button to power On the Smart Host.
•Hot Plug the Ethernet (LAN) Connection
Disconnect the Ethernet (LAN) connection from the controller
for 15 seconds and then reconnect.
Precautions
SURGE PROTECTION!
Use a surge-protected circuit for all components and power
supplies requiring 120-240V AC 50/60 Hz source power.
ELECTRICAL DISCONNECT!
The 120-240V AC 50/60 Hz source power outlet and input
power sockets should be easily accessible in the event of an
electrical hazard or malfunction condition.
CAUTION!
The SVR-SMRTD-10 contains intake and exhaust vents on each
side of the chassis. Do not block the vents or it will affect
performance and could result in damage to equipment.
Power Management Recommendations
Savant recommends a pure sine wave uninterruptible power supply
(UPS) with the ability to shut down the Smart Host Controllers
before the battery runs out of power. Never remove power from the
Smart Host Controllers before shutting it down.
Additional Documentation
For additional information, refer to the following documents on
Savant.com.
•HST-SMRTD Savant Smart Host: Deployment Guide - 009-1131-xx
SVR-SMRTD-10 | 009-1265-02 | 150223
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
2of 2
savant.com | 508.683.2500