Savant PAV-AOMWS1C-00 User manual

Savant IP Audio WiSA Bridge (Stereo) Quick Reference Guide | 009-1969-01 45 Perseverance Way, Hyannis, MA 02601
Copyright 2020 Savant Systems, Inc | 200820 1 of 2 www.savant.com | 508.683.2500
Box Contents
(1) Savant IP Audio Bridge (Stereo) [PAV-AOMWS1C]
(1) Install Kit [075-0253-xx]
(1) Mounting Plate [074-0577-xx]
(1) Product and Regulatory Insert [009-1950-xx]
Optional Accessories (sold separately)
Power Supply 5V DC 3.0A [PWR-5V3AI-xx]
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Cooling 10 CFM
Maximum BTU 34.1 BTU/hr
Dimensions and Weights
Height 1.4 in (3.5 cm)
Width 6.0 in (15.2 cm)
Depth 3.2 in (8.1 cm)
Weight Net: 0.5 lb (0.22 kg)
Shipping 1.5 lb (0.68 kg)
Rack Space 1U
Power
Power over
Ethernet (PoE) IEEE 802.3af
Nominal Power 3.5 watts
Maximum Power 5 watts
Input Power 5V DC 3A (from optional power supply)
Regulatory
Safety and
Emissions
FCC Part 15 CE
RoHS Compliant
Minimum Supported Release
Savant Software da Vinci 9.4
Front Panel
Reset Status
A B
AReset Button
To clear all Ethernet settings and revert them
back to their factory defaults, press and hold the
reset button for five seconds until the LED blinks
red rapidly; then release.
BStatus LED
O: Embedded processor resetting or booting
firmware.
Green: Communication with Host established.
Blinking Green: System ready but no
communication with Host.
Red: Firmware update failure, unit will reset.
Blinking Red: Firmware is running but has not
received a DHCP IP address.
Amber: Firmware update in progress.
Blinking Amber: Valid link-local IP address.
Rear Panel
DC
BA
AEthernet
8-pin RJ45 port.
Supports Audio Video Bridging (AVB) and Power
over Ethernet (PoE)
BDigital
Audio In
Digital Optical Audio (TOSLink) input.
Supports up to 192kHz/24 bit digital audio in;
PCM stereo format only.
CAnalog
Audio In
3.5mm Analog stereo line input (left and right).
Direct line level 2.1-VRMS input
DPower In 5V DC 3A
IMPORTANT NOTE! Use of both audio inputs simultaneously is
not supported by this device.
WiSA
Savant® IP Audio WiSA Bridge (Stereo) Quick Reference Guide

Savant IP Audio WiSA Bridge (Stereo) Quick Reference Guide | 009-1969-01 45 Perseverance Way, Hyannis, MA 02601
Copyright 2020 Savant Systems, Inc | 200820 2 of 2 www.savant.com | 508.683.2500
Installation
The IP Audio WiSA Bridge can be installed on a solid, flat, level surface
such as a table, cabinet, or shelf. The location should be dry, well
ventilated, and out of direct sunlight.
Mounting Plate
A mounting plate (074-0577-xx) is supplied with the IP Audio WiSA
Bridge. This mounting plate is used to mount the device to a wall or
existing structure. To mount the device, follow the instructions below.
1. Align the mounting plate onto the wall where the device will be
located. Position the bracket so the tabs that hold the device are
positioned horizontally.
2. Mark the two mounting holes on the wall.
3. Install wall anchors and screw mounting plate to the wall.
4. Snap the PAV-AOMWS1C into the bracket so the tabs on the
mounting bracket seat into the slots on the side of the device.
Mounting
Bracket
Tab fits
into slot
Network Configuration
To ensure that IP addresses will not change due to a power outage
or network event, a static IP address or DHCP reservation should
be configured for each device. Savant recommends using DHCP
reservation at the router, which allows IP addressing for all devices
to be managed from a single UI, avoiding the need to access devices
individually. The process for configuring DHCP reservation varies from
router to router. Refer to the manufacturer’s documentation for the
router in use on site for details..
Network Requirements
The PAV-AOMWS1C uses a Audio Video Bridging (AVB) network.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of trac or packet shaping in your network topology for the Savant
devices as this may interfere with performance.