SAVEO SAVEO-RV2-Z12D Setup guide

Reading Mode
SAVEO-RV2-Z12D
Advanced Settings
Demo
.
The default setting for reading mode is Single Scan. To choose another mode please scan the
appropriate barcodes below.
Motion Sensor: Full Auto Mode
In this mode the scanner attempts to decode when it
senses motion.
Motion Sensor: Semi Auto Mode (LEDs On)
In this mode the scanner’s aiming pattern and
illumination LEDs will turn on when it senses
motion. You will still need to press the scan button
to decode.
Motion Sensor: Semi Auto Mode
In this mode the scanner’s aiming pattern will turn
on when it senses motion. You will still need to press
the scan button to decode.
Demo
Demo
Demo
Single Scan (Default)
In this mode the scanner attempts to decode when
the scan button is pressed.
Redundancy Level
This scanner oers two levels of decode redundancy. Select the higher redudancy level for
poorer quality barcodes.
Demo
Redundancy Level 1
Barcode must be succesfully read twice before
being decoded
Redundancy Level 2
Barcode must be succesfully read three times before
being decoded
Demo

In this mode the scanner attempts to decode when it
senses motion.
Transmission Speed
Transmission speed is dependent on your device. In order not to lose data please choose the
correct speed. Mid Speed is the default.
Demo
%B%T%H
High Speed Transmission
Demo
Mid Speed Transmission (Default)
Demo
%B%T%L
Low Speed Transmission
Demo
Ultra Low Speed 1 Transmission
Demo
Ultra Low Speed 2 Transmission
Demo
Ultra Low Speed 3 Transmission
Keyboard Country
.
Scan the appropriate country code below to program the keyboard for your country or language.
As a general rule, the following characters are not supported by the scanner for countries other
than the United States: @ | $ # { } [ ] = / ‘ \ < > ~
Demo
%+-$.00
USA (Original setting)
Demo
%+-$.01
Norway
Demo
%+-$.02
Germany
Demo
%+-$.03
Sweden
Demo
%+-$.04
Denmark
Demo
%+-$.05
Switzerland
Demo
%+-$.06
Italy
Demo
%+-$.07
France
www.tec-it.com
%+-$.08
V ietnam
Demo
%+-$.09
S pain
Demo
%+-$.10
Portugal
Demo
%+-$.11
Hungary

Symbologies
Scan the following barcodes to enable/disable specic symbologies.
Demo
www.tec-it.com
Demo
.
Demo
Demo
.
Demo
Demo
.
Demo
Demo
.
Demo
www.tec-it.com
Demo
UPC-E
ENABLE DISABLE
UPC-A
ENABLE DISABLE
EAN-8
ENABLE DISABLE
EAN-13
ENABLE DISABLE
Code
ENABLE DISABLE
ISBT
ENABLE DISABLE
www.tec-it.com
.
Demo
.
www.tec-it.com
Demo
.
Demo
Demo
Demo
Demo
.
Code 39
ENABLE DISABLE
Code 39
FULL ASCII
ENABLE DISABLE
Trioptic
Code 39
ENABLE DISABLE
Code 32
ENABLE DISABLE
Demo
Demo
.
Demo
Demo
.
.
CODE 93
ENABLE DISABLE
CODE 11
ENABLE DISABLE
Interleaved
25
ENABLE DISABLE
Demo
Demo
Demo
Demo
.
Demo
Demo
Discrete
25
ENABLE DISABLE
CODABAR
ENABLE DISABLE
MSI
ENABLE DISABLE
www.tec-it.com
.
Demo
Demo
Demo
.
Demo
Demo
Chinese 25
ENABLE DISABLE
ENABLE DISABLE
Matrix 25
GS1 DataBar
ENABLE DISABLE
Demo
Demo
www.tec-it.com
Demo
.
Demo
Demo
Composite
CC-C
ENABLE DISABLE
Composite
CC-A/B
ENABLE DISABLE
Composite
TLC 39
ENABLE DISABLE
1D Symbologies

2D Symbologies
Demo
.
Demo
.
Demo
Demo
.
Demo
Demo
.
Demo
Demo
.
Demo
Demo
Demo
.
Demo
.
Demo
Demo
PDF 417
ENABLE DISABLE
Micro
PDF 417
ENABLE DISABLE
Data Matrix
ENABLE DISABLE
Maxicode
ENABLE DISABLE
QR CODE
ENABLE DISABLE
Micro
QR CODE
ENABLE DISABLE
Aztec
ENABLE DISABLE

Full Charge Alarm - OFF
Demo
%E%R%A
Please scan the following barcodes in order
Wait three seconds for conrmation sound
before scanning the barcode below.
SAVEO-RV2-Z12D
US PH: [phone] Email: [e-mail] UK PH: [phone]
www.saveoscan.com

QR Inverse
This parameter sets the QR inverse decoder setting. Options are:
•Regular Only - the decoder decodes regular QR bar codes only.
•Inverse Only - the decoder decodes inverse QR bar codes only.
•Inverse Autodetect - the decoder decodes both regular and inverse QR bar codes.
Regular
Inv erse Only
Inv erse Autodetect
SAVEO-RV2-Z12D
US PH: [phone] Email: [e-mail] UK PH: [phone]
www.saveoscan.com

E1
E2
Demo
.
Demo

BEEP AFTER GOOD DECODE
Scan a bar code below to select whether or not the decoder issues a beep
signal after a good decode. If selecting Do Not Beep after Good Decode,
beeper signals are issued during parameter menu scanning and to indicate
errors.
< Beep After Good Decode >
Do Not Beep After Good Decode
(Disable)
SAVEO-RV2-M22D
US PH: [phone] Email: [e-mail] UK PH: [phone]
www.saveoscan.com

suffix - enable suffix - disable
Disable/Enable sux (”Enter”)
Please scan the following barcodes (1 - 4) followed by“sux - disable”
to disable sux from being appended to barcode data.
You can then enable and disable sux (”Enter”) as desired with the
two barcodes below (you do not need to scan barcodes (1 - 4) again).
1
2
3
4
SAVEO-RV2-M22D
US PH: [phone] Email: [e-mail] UK PH: [phone]
www.saveoscan.com

Transmit UPC-A Check Digit
The check digit is the last character of the symbol used to verify the integrity of
the data. Scan the appropriate barcode below to transmit the barcode data
with or without the UPC-A check digit. It is always verified to guarantee the
integrity of the data.
< Transmit UPC-A Check Digit >
Do Not Transmit UPC-A Check Digit
US PH: [phone] Email: [e-mail] UK PH: [phone]
www.saveoscan.com
SAVEO-RV2-Z12D

Reset to factory defaults
Demo
%E%R%A
Please scan the following barcodes in order
Wait three seconds for conrmation sound
before scanning the barcode below.
SAVEO-RV2-M22D
US PH: [phone] Email: [e-mail] UK PH: [phone]
www.saveoscan.com
If connecting via Bluetooth, please unpair your device from the scanner before scanning the barcodes below.
After resetting your scanner you will need to pair it to your device using the“Wireless BT Communication”
barcodes on page 5 of the manual.
Unpairing your phone
Go to the Bluetooth menu on your phone and select the
option menu for scanner from list of paired devices. Choose “Forget this Device”/”Unpair”