SAVEO SAVEO-SCAN-PKT-M22D-BT User manual

Scanning with Simplicity
www.saveoscan.com
SAVEO-SCAN-PKT-RCCD-BT

Table of Contents
Product Information 3
Getting Started 5
Operating Elements 5
Connecting to iOS via Bluetooth 6
Connecting to Android via Bluetooth 8
Unpairing your device 11
Operating Modes 13
Reset to Defaults 15
LED Indicator 16
Power Saving Mode 16
Further Information 17

3
Delivery contents
* SAVEO-SCAN-PKT-M22D-BT scanner x 1
* Strap x 1
* Mini USB cable x 1
* Quick instructions x 1
Limited Warranty
Saveo Scan provides a one year limited warranty.
This warranty does not cover any product which has been
subject to improper use, neglect or unauthorized repair or
installation.
This warranty does not cover consumable parts. (Cables &
batteries are consumables.)
Safety instructions
Read the operating instructions carefully and pay special
attention to the safety information. If you do not follow the
safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury
or damage to property.
* Don’t put scanner in places of excessively high
temperature, such as exposure to direct sunlight
* Don’t use scanner in extremely humid conditions or in
conditions of extreme temperature change
* The rechargeable battery is permanently built into the
product and cannot be replaced.
* Never damage the rechargeable battery. Damaging
the casing of the rechargeable battery might cause
explosion or re!
Product Information

5
Getting Started
Switch on and Charge your Scanner
Please switch on and charge your scanner for 3~4 hours
before rst use.
Exit window
Scan/Power
On Button Power Saving
button:
Press the button for
2~3 seconds to
enter power saving
Mini USB port
with protective cover
Charge the pocket scanner with mini USB cable.
LED Indicator
Please note: LED indicator will remain red until scanner has
been paired with a device.
(For iOS Devices
ONLY)
Button to
raise and lower
ON-Screen
Keyboard
Operating Elements

6
Connecting to iOS via Bluetooth
Enable Bluetooth on your device
Go to your phone’s homescreen and nd “Settings”, then
“Bluetooth” and turn Bluetooth on.
Press and hold
for 3-4 seconds
to pair to your
device.
Pair your device to the scanner
Press and hold the left button (as
illustrated) for 3-4 seconds. You will
hear a notication sound and the
scanner will become visible to your
device.

7
Devices are now
paired.
Once “Connected” is
displayed, your device is
paired to the scanner.
Your scanner is now
ready to use.
Please note: devices only need to be paired once. When they are within
Bluetooth range they will automatically attempt to connect to each other. If
you wish to pair to another device it is recommended you rst unpair this
device.
You are now connected. Start scanning.
Search for devices
Your phone will automatically search for devices, Saveo Scan
will appear as an external keyboard with a unique identier
number (R-xxxxxx).
Select R-xxxxxx to
connect
Select scanner from
“Available Devices” and
wait for pairing process
to complete.

8
Connecting to Android via Bluetooth
Enable Bluetooth on your device
Go to your phone’s homescreen and click on the menu button
to nd “Settings”, then “Bluetooth” and switch bluetooth on.
Press and hold
for 3-4 seconds
to pair to your
device.
Pair your device to the scanner
Press and hold the left button (as
illustrated) for 3-4 seconds. You will
hear a notication sound and the
scanner will become visible to your
device.

9
Search for devices
Click “Search for Devices” at the bottom of the screen and
Saveo Scan will appear as an external keyboard with a unique
identier number (R-xxxxxx).
Select R-xxxxxx to
connect
Select scanner from
“Available Devices” and
wait for pairing process
to complete.

10
Devices are now
paired.
Once “Connected” is
displayed, your device is
paired to the scanner.
Your scan- ner is now
ready to use.
Please note: devices only need to be paired once. When they are within
Bluetooth range they will automatically attempt to connect to each other. If
you wish to pair to another device it is recommended you rst unpair this
device.
You are now connected. Start scanning.

11
Press and hold
for 3-4 seconds
to unpair from
device.
Using the scanner to unpair
Unpairing using your phone
Unpairing your device
Before connecting the scanner to another device it is recom-
mended you rst unpair from the current device.
This can be done on the scanner or through the system menu
on your smartphone/tablet.
To unpair using the scanner, press
and hold the left button (as illustrat-
ed) for 3-4 seconds. You will hear a
notication sound and the LED will
turn red to indicate it is not paired to
any device.
Go to the Bluetooth menu on your phone and select the
option menu for scanner from list of paired devices.

12
Choose “Forget this Device”/”Unpair”

13
There are two operating modes on the scanner, Data trans-
mission mode and Data Storage Mode.
Scan the appropriate barcodes when switching between these
two modes.
Please note: Switching between modes will wipe the
scanner’s internal memory.
Operating Modes
Data Transmission Mode (Default)
Our Default setting is Data Transmission mode. In this mode
data will be sent to smartphone/tablet directly.
To enter Data Transmission Mode please scan the follwing
barcodes.
Demo
%E%R%A
Demo
%M%A%F
Enter Data Transmission Mode
Green/Orange LED ashes followed by 3 beeps.

14
Demo
%E%R%A
Clean Memory Data
Green/Orange LED ashes
followed by 3 beeps.
Demo
%M%A%N
Data Storage Mode
In this mode, data will be saved directly to scanner’s memory.
Scan Transmit Memory Data to receive data stored on
scanner’s internal memory.
Enter Data Storage Mode
Green/Orange LED ashes followed by 3 beeps.
Demo
%E%R%A
To enter Data Storage Mode please scan the follwing
barcodes.
Demo
%R%E%C
Transmit Memory Data
Green/Orange LED ashes
followed by 3 beeps.
Transmit Memory Data
Scan the following barcode to receive data stored in the
scanner’s internal memory..
After data is transmitted to your device it remains on the
scanner’s internal memory. Scan the following barcode to clear
the memory if you do not wish to send this data again.

15
Reset Conguration to Defaults (scan from A1to A6)
HID Prole
Reset to Defaults
Demo
W010F01
Demo
WFFD980
Demo
W100900
Demo
WFFD9C3
Demo
W010F00
Demo
A1
A2
A3
A4
A5
A6

16
When the battery power is too low, the Orange LED will ash
and beep once. Scanner should be charged immediately. If
scanner shuts down it is recommended to charge it fully then
power it back on.
Under power-saving mode, there will not be an LED indica-
tion when charging.
Orange LED ON Full charged
Orange LED (Flashing) Charging / Low battery
Red LED ON Oine / Out of Range
Green LED ON Good read
Orange LED ON Good read (Batch mode)
LED Indicator Information
LED Indicator
.
Power saving mode is enabled by default and will put the
scanner to sleep after 1 minute’s inactivity. To wake up the
scanner press the trigger.
Demo
%P%D%T00
Disable
Scan to disable power saving
mode
Demo
Enable
Scan to enable power saving
mode
Below are the barcodes to disable/enable power saving mode.
Power Saving Mode

17
Full User Manual and Spec sheet can be downloaded at:
www.saveoscan.com/downloads
Further Information
Units 5-6
Ballywaltrin Business Park
Boghall Road
Bray
Co. Wicklow
Ireland
US PH: [phone]
UK PH: [phone]
IRE PH: [phone]
Email: [e-mail]
For more information, contact us at: