SBC R-102-D5 User manual

R-102-D5/N6/N8 Series
Mini-ITX Motherboard Support Socket G2 for
Intel® ATOM D2550/N2600/N2800 CPU, VGA/LVDS/DVI,
Dual GbE, PCI, SATA 3Gb/s and Audio.
R-102-D5
R-102-N6/N8

R-102 Series User’s Manual
2
R-102-D5/N6/N8
USER’S MANUAL
Note :
1. R-102-XX series : 2x LAN, 6x COM port.
2. R-102L-XX series : 1x LAN, 2x COM port.
Rev. A1.0 - Nov 15, 2012
Model No. Description
R-102-D5 Intel ATOM D2550 1.86 GHz 2x 512K L2, 10W TDP, dual-core CPU
R-102-N6 Intel ATOM N2600 1.6 GHz 2x 512K L2, 3.5W TDP, dual-core CPU
R-102-N8 Intel ATOM N2800 1.86 GHz 2x 512K L2, 6.5W TDP, dual-core CPU

Revision
3
Revision
Date Version Changes
Nov 15, 2012 A1.0 Initial release

R-102 Series User’s Manual
4
Notice
Copyright
The copyright of this user’s guide belongs to any authorized
company and is protected by copyright law. This means partial or
full duplication of this document (electronically, mechanically or
otherwise) is prohibited without the permission of the authorized
company.
The contents may be modified without notice for the improvement
of design, function, and reliability.
We do not guarantee the prevention of data loss. Please be
cautious not to lose important data and keep back-ups at all times.
Even though we did our best in drawing up this user’s guide, there
may be omissions and errors we failed to notice. Manufacturers
and suppliers cannot be held liable for problems stemming from
those errors and omissions.
Registered Trademark
Microsoft Windows 7 is a registered trademark of Microsoft.
Intel ATOM are registered trademarks of Intel.
Company names and product names mentioned in this document
are used to help your understanding and are registered
trademarks.

Notice
5
Introduction
Thanks for choosing the next generation high performance motherboard
“R-102-D5/N6/N8 series”. The uses the high performance Intel®NM10 chipset
that will deliver superior performance to your computer.
About This User’s Guide
This User’s Guide is for assisting system manufactures and end user in setting
up and installing the motherboard. Information in this guide has been carefully
checked for reliability, however, there may still be inaccuracies and information
in this document is subject to change without notice.
DISCLAIMER
The information in this manual has been carefully checked and is believed to
be accurate. We assume no responsibility for any inaccuracies that may still be
contained in this manual. We reserve the right to make changes to this material
at any time without notice.
REMARK
Intel® ATOM CPU is registered trademark of Intel Corp.
All other trademarks mentioned in this manual are registered property of the
respective owners.

R-102 Series User’s Manual
6

Table of Content
7
Table of Content
Notice ............................................................................................ 4
Copyright ...................................................................................................4
Registered Trademark ..............................................................................4
Introduction ...............................................................................................5
About This User’s Guide ..........................................................................5
DISCLAIMER..............................................................................................5
REMARK ....................................................................................................5
Table of Content ........................................................................... 7
Chapter 1 : Unpacking ............................................................... 10
1.1 Anti-static Precautions .....................................................................10
1.2 Unpacking Precautions ....................................................................10
1.3 Packing List ....................................................................................... 11
1.3.1 Optional Items ......................................................................................................11
Chapter 2 : Introduction............................................................. 12
2.1 Introduction .......................................................................................12
2.2 Connectors ........................................................................................13
Front side : ................................................................................................................... 13
2.3 Dimensions........................................................................................14
2.3.1 Board Dimensions............................................................................................... 14
2.3.2 External Interface Panel Dimensions.................................................................. 15
2.4 Block Diagram Block Diagram .........................................................16
2.5 Technical Specifications...................................................................17
Chapter 3 : Connectors.............................................................. 20
3.1 Peripheral Interface Connectors......................................................20
3.1.1 R-102 Series Layout ........................................................................................... 20
3.2 Internal Peripheral Connectors/Jumpers ........................................21
3.2.1 Audio Connector : CN_AUDIO1(Pitch 2.54mm) ................................................. 21
3.2.2 SPDIF Connector : CN_SPDIF1(Pitch 2.0mm) .................................................. 22
3.2.3 Boot Up Mode Jumper : CN_AT1(Pitch 2.0mm)................................................. 22
3.2.4 Front Panel Connector : CN_PANEL2 (Pitch 2.54mm) ...................................... 23
3.2.5 Clear CMOS Jumper : CN_JRTC1(Pitch 2.54mm)............................................. 24
3.2.6 COM2 RS232/422/485 Jumper : (Pitch 2.0mm) CN_JCOM2_SEL1 /
CN_JCOM2_SEL2 ....................................................................................................... 25
3.2.7 COM1 / COM2 Voltage Setting Jumper : (Pitch 2.0mm) CN_JCOM1 /

R-102 Series User’s Manual
8
CN_JCOM2.................................................................................................................. 26
3.2.8 COM3~6 Connector : CN_COM3~6(Pitch 2.0mm)............................................. 27
3.2.9 COM3~6 Voltage Setting Jumper : CN_JCOM3~6 (Pitch 2.0mm) ..................... 28
3.2.10 SPI Flash Connector : CN_SPI1 (Pitch 1.27mm) ............................................. 28
3.2.11 LVDS Voltage Jumper : CN_ JLVDS1 (Pitch 2.54mm) ..................................... 29
3.2.12 PS2 KB/Mouse Connector : CN_PS1 (Pitch 2.0mm) ....................................... 29
3.2.13 LVDS Connector : CN_LVDS1(Pitch 1.25mm) ................................................. 30
3.2.14 LVDS Panel Type Select : CN_JLVDS_SEL1(Pitch 2.0mm) ............................ 31
3.2.15 Panel On/Off : CN1(Pitch 2.0mm)..................................................................... 32
3.2.16 Digital I/O Connector : CN_DIO1(Pitch 2.0mm) ............................................... 32
3.2.17 Inverter Power Connector : CN_INV1(Pitch 2.0mm) / CN_INV2(Pitch 1.25mm)
..................................................................................................................................... 33
3.2.18 Parallel Port : CN_LPT1(Pitch 2.0mm) ............................................................. 34
3.2.19 USB Connector : CN_USB1(Pitch 2.0mm) / CN_USB2 / CN_USB3(Pitch
2.54mm) ....................................................................................................................... 35
3.2.20 SMBUS Connector : CN_SMBUS1(Pitch 2.0mm) ............................................ 36
3.2.21 CPU / SYSTEM FAN Power Connector : CPUFAN1 / SYSFAN1..................... 36
3.2.22 SATA Connector : SATA1~2.............................................................................. 37
3.2.23 ATX / DC IN Power Connector : ATX1 / DC_IN1 .............................................. 38
3.3 External Peripheral Interface Connector Panel ..............................39
3.3.1 Ethernet and USB 2.0 Connector ....................................................................... 39
3.3.2 Serial Port Connector : COM1 / COM2............................................................... 41
3.3.3 Display Connector : CRT / DVI ........................................................................... 42
3.3.4 Audio Connector : AUDIO_JACK1 ...................................................................... 43
Chapter 4 : Installation............................................................... 44
4.1 Before Installation .............................................................................44
4.2 Install the SO-DIMM DDR3 RAM.......................................................45
4.3 Install the SIM card............................................................................46
4.4 Install the Mini PCI-E card ................................................................48
Chapter 5 : BIOS Setup .............................................................. 49
5.1 APM : ..................................................................................................49
5.2 Programming Watch Dog Timer : ....................................................49
5.3 Power Loss :......................................................................................50
5.4 Flash BIOS :.......................................................................................51
5.4.1 Flash Tool............................................................................................................ 51
5.4.2 Flash BIOS Procedure ........................................................................................ 51

Table of Content
9

R-102 Series User’s Manual
10
Chapter 1 : Unpacking
1.1 Anti-static Precautions
Make sure to adhere to the following guidelines:
Wear an anti-static wristband: Wearing an anti-static wristband can prevent
electrostatic discharge.
Self-grounding: Touch a grounded conductor every few minutes to
discharge any excess static buildup.
Use an anti-static pad: When configuring any circuit board, place it on an
anti-static mat.
Only handle the edges of the PCB: Don't touch the surface of the
motherboard. Hold the motherboard by the edges when handling.
1.2 Unpacking Precautions
When the motherboard is unpacked, please do the following:
Follow the antistatic guidelines above.
Make sure the packing box is facing upwards when opening.
Make sure all the packing list items are present.
WARNING!
Static electricity can destroy certain electronics. Make sure to follow the
ESD precautions to prevent damage to the product, and injury to the

Chapter 1 : Unpacking
11
1.3 Packing List
The R-102 series is shipped with the following components:
Item and Part Number Quantity
R-102 series Motherboard 1
SATA cable (CAB-N07330) 2
Dual RS-232 cable with bracket (NBS-COMBK1) 1
LPT printer cable with bracket (NBS-LPTBK0) 1
I/O Shielding (BKT-IR2717) 1
Utility CD 1
User Manual 1
1.3.1 Optional Items
The following are optional components which may be separately purchased:
Item and Part Number Quantity
ATX 20pin DC power cable (CAB-M20AD0)
This cable is for use power adapter.
If you want use over 2x 3.5” HDD, please make sure the
watts of power adapter is enough to support.
1
Dual USB cable with bracket (CAB-M09U20) 1
KB/MS Y cable (CAB-N08B20) 1
If any of the components listed in the checklist below are
missing, do not proceed with the installation. Contact the
reseller or vendor.

R-102 Series User’s Manual
12
Chapter 2 : Introduction
2.1 Introduction
The R-102 series Mini-ITX motherboard is a Intel® ATOM processor platform.
Up to two 4.0 GB 800/1066 MHz DDR3 SDRAM SO-DIMM are supported by
the Intel® processor. NM10 chipset supports a PCI slot.
The integrated Intel® NM10 Express Chipset supports two GbE LAN: all
through the Intel® 82574L Ethernet controller, Wake-on-LAN, PXE ready
The Intel® NM10 also supports two SATA 3Gb/s drives.
The R-102 series supports multiple display devices, including 18-bit or 24-bit
dual-channel LVDS, analog CRT, and DVI. 6x USB 2.0 channels,
and one expansion PCIe mini socket. High Definition Audio (HDA) support
ensures HDA devices can be easily implemented on the R-102 series.

Chapter 2 : Introduction
13
2.2 Connectors
The connectors on the R-102 series are shown in the figure below.
Front side :
LAN and
USB 2.0
VGA
DVI
DB-9
Serial port :
COM1
COM2
Audio :
Line In
Line Out
Mic
Front Audio
SPDIF
SIM Socket
Mini PCIe
Digital I/O
Buzzer
Battery
DB-9 Serial port :
COM3~6
PCI slot
Power / Reset
Buttons,
Indicators
CMOS/AT/ATX
USB 1/2/3
SATA1/2 DDR3 So-DIMM
Socket
PS2 KB/MS
SMBUS
SYS FAN
ATX 20pin
LVDS Panel
Voltage supply
DC IN 4pin
LVDS
Parallel port
DB-9 Serial port :
COM1~2

R-102 Series User’s Manual
14
2.3 Dimensions
2.3.1 Board Dimensions
The dimensions of the board are listed below :
Length: 170 mm / Width: 170 mm

Chapter 2 : Introduction
15
2.3.2 External Interface Panel Dimensions
External peripheral interface connector panel dimensions are shown below :.

R-102 Series User’s Manual
16
2.4 Block Diagram Block Diagram
The data flow between the two on-board chipsets and other components
installed on the motherboard and described in the following sections of this
chapter.
SO-DIMM1
(800/1066 MHz)
Intel® ATOM
D2550 / N2600 / N2800
Processor
Intel®
NM10
Interface 20-Gbit/s
SO-DIMM2
DDR3 SDRAM
LVDS (18/24bit)
VGA
DVI
2x SATA II
SPI ROM
Realtek ALC888
Audio Jacks
Audio Connector
SPDIF
2x Intel®82547L
Mini PCIe Slot
7x USB 2.0
BIOS debug port
Super I/O
W83627DHG
Fintek
F81216AD
COM1~2
2 x FAN
8-bit DIO
KB/MS
COM3~6
CRT
DP CH7511B
PCIe x1
USB
SMBUS
LPC
GPIO
LPC
PCIe x2
HD Audio
SPI
SATA
Channel A
Channel B
PCI Slot
32bit/33MHz PCI Bus
AU 6258
3x USB 2.0
LPT

Chapter 2 : Introduction
17
2.5 Technical Specifications
R-102 technical specifications are listed in table below.
Processor
Intel® AtomTM processor N2800, 1.86 GHz 2x 512K L2,
6.5W TDP, dual-core heatsink (fanless solution)
Intel® AtomTM processor N2600, 1.6 GHz 2x 512K L2,
3.5W TDP, dual-core heatsink (fanless solution)
Intel® AtomTM processor D2550, 1.86 GHz 2x 512K L2, 10W
TDP, dual-core heatsink (with cooling fan)
Chipset Intel® NM10 Express Chipset
Memory
2 x DDR3-800/1066 SO-DIMM up to 8 GB
technologies are supported for x8 and x16 devices,
unbuffered, non-ECC
at 800/1066 MHZ on N2800 and D2550(Max 8GB)
at 800 MHZ on N2600(Max 4GB)
(ATOM N2600 only support one memory module.)
(When you install only one memory module, install it on
SO-DIMM 2 slot)
Storage 2 x SATAII interface with 300MB/s transfer rate
Video
Intel® GMA 3650 graphics core for N2800 and D2550
Intel® GMA 3600 graphics core for N2600
Supports Hardware H.264/AVC, MPEG-2 video decoder,
VC-1, DirectX 9, 1080p decoder
Onboard 24-bit dual channel LVDS interface with
3.3V/5V/12V Support
VGA display resolution up to 1920x1200

R-102 Series User’s Manual
18
LVDS supports 24-bit dual-channel by CH7511 DP to
LVDS converter, resolution support up to
1920x1200 for D2550, 1600x1200 for N2600/N2800
Audio Realtek ALC888 HD 6-channel CODEC
Line out / line in / microphone ports
Super I/O W83627DHG
Interface ports
Rear side :
2x Serial, DB-9 connector :
1x RS232(COM1), 1x RS485/422/232(COM2)
VGA(CRT)
DVI
2x RJ45 LAN
4x USB 2.0
Line out / line in / microphone.
DC In
USB Port External : 4x USB 2.0 ports.
Internal : 6x USB 2.0 (6x jumper pin) ports.
Expansion Slots
1x PCI slot
1x Mini PCI-E slot
1x SIM socket
Communications Intel 82574L Gigabit LAN, Wake-on-LAN, PXE ready
Internal I/O port
1x PS2 KB/Mouse (8-pin header)
1x SMBus (4-pin header)
1x SPDIF/out (4-pin header)
1x GPIO (Onboard Programmable 8-bit Digital I/O
interface(4 In+4 Out), 12-pin header) ;
4x RS232 (COM3/4/5/6, 10-pin header)
BIOS UEFI BIOS label

Chapter 2 : Introduction
19
Watchdog Timer Software programmable supports 1~255 sec. system reset
Boot Up mode ATX / AT
Power Connector Standard 20-pin ATX power supply and
Power adapter DC 9 ~ 24V input
Operation Humidity 10% ~ 95% relative humidity, non-condensing
Temperature Operating: 0°C ~ +60°C (32°F ~ 140°F), Storage: -20°C ~
+80°C (-4°F ~ +176°F)
Dimensions Mini-ITX form factor, 170mm (L) x 170mm(W)
Weight GW/NW 900g/320g

R-102 Series User’s Manual
20
Chapter 3 : Connectors
3.1 Peripheral Interface Connectors
This chapter details all the jumpers and connectors.
3.1.1 R-102 Series Layout
The figures below show all the connectors and jumpers.
82574L 82574L
NM10
SO-DIMM1
CPU FAN1
SO-DIMM2
A
TX1
CN SMBUS1
SYS FAN1
CN_INV1 CN_INV2
SATA2
SATA1
CN_USB2
CN_USB3
CN_USB1
CN
_
PANEL2
CN_SPI1
CN_AT1
CN_JCOM5
CN_COM5
CN
_
SPDIF1
CN_AUDIO1
CN_JLVDS1
CN_JLVDS_SEL1
CN_LPT1
CN_DIO1
MINI_CARD1
CN_SIM1
CN_LVDS1
CN_JCOM2_SEL1
CN_JCOM1
CN_JCOM2
CN_JCOM2_SEL2
USB_RJ45_2USB_RJ45_1
COM1(TOP)_COM2
DVI_CRT
A
UDIO_JACK1
CN_PS1
CN1
CN_JCOM3
CN_COM3
CN_JCOM4
CN_COM4
CN_JCOM6
CN_COM6
CN_JRTC1
ATOM
D2550 /
N2600 / N2800