Scarlet Tech Apollo M1 User manual

Apollo M1
Quick Set-Up Guide
Wireless Solar Crane Camera

<Lower Layer><Upper Layer>
(8+17)(5+15) (4+20)(2)(1)(3)
(13+14) (18)(6)(10)(7) (16)
(9+11) (12)
(10)
Product Content
Main Products
(1) Hook-View Camera x 1
(2) Winch-View Camera x 1
(3) Solar Power Station x 1
(4) Touchscreen Monitor x 1
Cables & Accessories
(5) Monitor Display Mount x 1
(6) Monitor Power Adapter x 1
(7) Stainless-steel Safety Lanyard (1 M) x 1
(8) Battery Power Charger x 1
(9) Battery Power Cable x 1
(10) Magnetic Cord Holder x 6
(11) Hook-View Camera 5-Pin Power Cable x 1
(12) Winch-View Camera Power Adapter x 1
(13) Panel Directional Antenna x 1
(14) Panel Directional Antenna Signal Cable (0.5M) x 2
(15) Panel Directional Antenna Mount x 1
(16) Omnidirectional Antenna (Hook-View & Winch-View Camera) x 2
(17) Scarlet 4G Router Bundle (Power adapter x 1, Antennas x 2, Ethernet Cable x 1)
(18) Quick Set-up Guide, User Guide, Certificate of Conformity
(19) Waterproof Carry-on Case (26”) x 1
(20) MicroSD Card (64GB) x 1

Set Up Instructions
1. Insert a MicroSD card into the card slot at the side of the monitor.
2. Turn ON the LCD monitor. Tap the screen to display dual-screen view.
(4)
Note:
• MicroSD is for video recording.
• Supports MicroSD card with a maximum capacity of 256GB.
1
<1> Touchscreen Monitor
2
(20)

1. Install omnidirectional antenna on the SMA port.
2. Wipe clean the crane hoist surface.
3. Mount the hook-view camera on the crane’s hook surface.
4. Mount the power station on the crane’s hook surface, above the hook-view camera.
<2> Hook-View Camera & Solar Power Station
1 2
3
4
(1)
(3)
(16)

Tips : Neatly organize the
cables using magnetic cord
holder.
5. Connect hook-view camera and the solar power station using the hook-view Camera 5-Pin
power cable.
5
(10)
(11)

6. Turn ON the solar power station.The LED indicator will show a green light.
7. Important step: Use paperclip or pen to press the pair button. Hook-view camera will show
a red light.
8. Check the hook-view camera display on the monitor screen.
6
7

Use the stainless-steel safety lanyard. Slide the lanyard over the anchor on the top of the
hook-view camera and on the back of the solar power station. Then lock the lanyard hook to
the crane to secure position.
Safety Precaution
(7)

Tips : Neatly organize the
cables using magnetic cord
holder.
<3> Winch-View Camera
1. Install antenna on the back of the winch-view camera.
2. Mount the winch-view camera on the crane’s winch surface.
1
2
(16)
(2)
(10)

Note: Adjust the angle using anchor screw
3. Connect winch-view camera power cable with the power adapter, then plug the power.
4. Check the winch-view camera display on the monitor screen.
(12)

<4> Placing Touchscreen Monitor
1. Install holder to monitor in clockwise direction.
2. Firmly press holder to mounting surface.
Note: Wipe clean surface before mounting.
1
2
(5)

3. Adjust position using the knob.
0.5M
4. Use panel directional antenna signal cable to connect the monitor and the antenna panel.
3
3
(13)
(14)

Diameter: 23~27.5mm
<5> Placing Panel Directional Antenna
1.Remove the screw and bolt, then pull the joint down.
2.Clip the holder to mounting surface.
Note: Make sure the distance between monitor and
directional panel antenna is less than 50cm
1
2
(15)

3. Close the joints first, then insert the bolts into the hole, screw tightly to lock position.
4. Adjust position using the knob.
3
4

5. Plug the panel directional antenna to the holder.
5
(13)

Note: Panel directional antenna must be facing the hook-view camera
for smooth signal transmission.
*Situation may vary depending on the crane types and actual operating environment.
Adjust antenna position pointing
towards the panel directional antenna
surface for smooth signal reception.
1. Tower Crane
2. Mobile Crane
Placement Recommendation

Pairing
Pairing Additional Camera:
Important Note: Apollo M1 hook-view and winch-view camera are already paired by default.
Make sure the monitor, hook-view, and winch-view camera are all turned ON before using.
The wireless cameras must be paired with the monitor before use.
1. Attach camera antenna.
4. On-screen go to Menu > Camera > Pairing > Tap the camera number you want to pair.
Tap the camera number 3 or 4. Each number represents one camera.
Camera 3: Additional Camera 1
Camera 4: Additional Camera 2
3. Important step: Use paperclip or pen to press the pair button at the back of the camera
to turn ON the pairing function. The infrared LED light will flash when it is turned on.
2. Place additional camera in your desired viewing area.

Scarlet Tech Co., Ltd.
© 2020 Scarlet Tech Co., Ltd. All rights reserved.
4F-3, No. 347 , HePing E Rd, 2nd Sec, DaAn District, Taipei City 106, Taiwan
[email protected]
www.scarlet-tech.com
version 200623