Schrack Seconet Integral PIP User manual

Operating panel Integral PIP
User manual

Schrack Seconet
0000 0000 0000
29.01.2020
INTEGRAL
Alarms Faults Disablements
FIRE
Site Info
Buzzer
silenced
Operation
Additional
Information
1
2
3
4
5 5
6 6
7
8910
11
12
13
ALED FIRE
BButton Site Info
CButton Buzzer silenced
DButton
EFreely programmable buttons
FFreely programmable LEDs
GDisplay
HButton and LED Alarms
IButton and LED Faults
JButton and LED Disablements
KLED Operation
LButton Additional Information
MNavigation buttons/scroll buttons
· Reset alarm/fault signal
Reset alarm/fault signal
Pressing the button Buzzer silenced C disables
the signal tone of an active alarm or fault message
in the fire alarm control panel; the LED remain lit
up. Any additional alarm or fault message will trig-
ger the alarm and fault signal tones again. Acknow-
ledgement and intervention signal tones cannot be
reset.
· Navigation buttons/scroll buttons
Navigation buttons/scroll
buttons
Scroll button I for selecting the previous list entry
(scroll up in the list). Scroll button H for selecting
the next list entry (scroll down in the list).
· Freely programmable buttons and LED
Freely programmable buttons
and LED
There are buttons E and LEDs F, which can be
freely programmed and labelled on the operating
panel as customers wish.

Display
Normal operation
Schrack Seconet
0000 0000 0000
29.01.2020
INTEGRAL
In an idle mode (standard indication), the display
shows product and customer information. The list
counters are set to 0. The Operation K LED in-
dicates the system’s current operating status.
Site information
SITE INFO
ZONE 103/1
CUSTOMER TEXT FOR DETECTOR 103/1
E.G. BUILDING, ROOM
0000 0000 0000
Pressing the button Site Info B displays site in-
formation.
Site information can be called up for each element
when in list view or element view. A customer-spe-
cific programmed text is displayed, e.g.
1ST FLOOR, CONFERENCE ROOM, ROOM 25.
Fire alarm
ALARMS 04:30
CUSTOMER TEXT FOR ZONE 103/1 0001
0001 0000 0000
A fire alarm is indicated visually and acoustically:
The FIRE A indication flashes, the alarm signal
sounds and the detector zone, detector number and
the number of alarms that have been received are
displayed on the operating panel display.
Pressing the button Alarms H displays an over-
view of all alarm messages.
Disablements
DISABLEMENTS 04:30
OFF PRINTER 1 0001
OFF 103/1 0002
OFF OUTPUT 65001 0003
OFF 9999/61 0007
0000 0000 0007
Pressing the button Disablements J displays
the list of all disabled elements.
The Disablements J LED lights up, if at least
one system element is disabled.
Additional information
ADDITIONAL INFO
ZONE 103
AUTOM-DETECTOR
OFF
29.01.2020 04:30
0000 0001 0000
Pressing the button Additional Information L
displays additional information.
In list view or element view, additional information
can be called up for each element, e.g. detector
zone, detector number, date and time or in case of
an event, e.g. alarm, fault, disablement or actuation.
Faults
FAULTS 04:30
FAULT ZO 103/1 0001
0000 0001 0000
The I LED flashes and the fault’s signal is sound-
ing, if there are faults (Chapter Reset alarm/fault sig-
nal). The list of faults Faults T displays the mal-
functioning component with element type, element
number and where applicable detector zone.
Pressing the button Faults I displays an overview
of all fault messages.

EN
Subject to technical changes © Schrack productions · B-HB-0109EN · V 2.0 · 01.2021
SCHRACK SECONET AG
Eibesbrunnergasse 18
A-1120 Vienna
Tel. [phone]
[email protected]
www.schrack-seconet.com