Schreiber Messtechnik 405769 User manual

Ref. no HB 05.07 Date: 18/04/11
Single/Double Internal
3 Drawer Chest
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 46,8/96,8cm
Depth - 45,8cm
Height - 56,8cm
405769
867492

Safety and care advice
Important – Please read these instructionsfully before starting assembly
Note: if required the next
page can be cut out and used
asreference throughout the
assembly. Keep thispage with
these instructionsfor future
reference.
• Check you have all the
componentsand toolslisted on
pages2 and 3.
Remove all fittingsfrom the
plastic bagsand separate them
into their groups.
• Keep children and animals
away from the work area, small
partscould choke if swallowed.
• Make sure you have enough
space to layout the partsbefore
starting.
• Do not stand or put weight
on the panels, thiscould cause
damage.
• Assemble the unit asclose
to itsfinal position (in the same
room) aspossible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Note: Only apply the glue
once you are sure of the
assembly.
• The wall plugssupplied are
suitable for solid wallsonly.
It isimportant that the correct
type of fixing isused for your
wall, seek professional advice if
in doubt.
• Partsof the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the
use of power drill/
driversfor inserting
screws, asthis
could damage the unit. Only use
hand screwdrivers.
• Warning: Before drilling,
check the wall for hidden pipes
and cables.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screwson
thisunit.
• Thisproduct should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. Thisprocedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately. If possible
show product information or
label to the medical advisor.
Glue safety - Take care when using glue, please follow the advice below
2

1
4
5
6
6
7
89
10
11
2
3
Raw
3
Components - Panels
Please checkyou have all the panels listed below
1) Left end panel x1
2) Right end panel x1
3) Top panel x1
4) Backrail x1
5) Front rail x1
6) Side filler x2
7) Front drawer x1
8) Left drawer side x1
9) Backdrawer panel x1
10)Right drawer x1
11)Drawer bottom x1

Wooden dowel x 32
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
E
Metal dowel x 14
B
30mm Screw x 6
C
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more
- ttings may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
F
D
G
J
P
x 12
H
25mm Screw x 16
Long locking
nut x 8
0 0 20 30 40 50 60 70 80 90 00 0 20 30 40 50
0 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Ø 5mm Suitable drill bit
(for use with wall plug)
Eye protection
(when using a
hammer or glue)
mm
x 3
Glue x 1
Runner x 3
Short locking
nut x 6 Block x 4
Components - Fittings
Please check you have all the fittings listed below
4

Assembly Instructions
Step 1
E
E
B
E
Prepare panels
J
G
1
C C
P
Please note the correct fixing holes in
the drawer runner – as shown. The top
row of holes are used and when fixed
into position the front edge of the
runner should sit 2 mm. from the front
of the end panel.
E
4
5
C
Top
Top
2
1
6
6
B
3
B
B
Raw
5

Assembly Instructions
Step 2
Step 3
1
3
2
Raw
E
E
4
5
6

Assembly Instructions
Step 4
Step 5
Note that the assembled cabinet
should be fitted into the wardrobe
before the hinge platesare fitted !
6
6
J
J
7

Assembly Instructions
Step 6
c:
A
b:
A10
8
11
9
D
D
d:
e:
F
a: O
A
F
B
8
10
9
A
A
A
A
B
B
F
M
Assembly for
drawer boxes
F
F
8

Assembly Instructions
Step 7
Insert drawer
a:
b:
c:
d:
FIX
Ensure plastic securing
pegsare to the out
position.
Drawer front adjustment
Drawer front
9

Assembly Instructions
Step 8
Step 8b
Handle fitting
Handle fitting
Handle drill
knob drill
Only for Double drawer
Blind holes are pre-drilled on the
back face of the doors & drawers.
Use these as a guide to drill through
with 5mm. drill bit together with
scrap piece of wood to avoid
chipping the front face.
Included with handle
Only for SINGLE drawer
Blind holes are pre-drilled on the
back face of the doors & drawers.
Use these as a guide to drill through
with 5mm. drill bit together with
scrap piece of wood to avoid
chipping the front face.
Included with handle
Handle drill
knob drill
10

Assembly Instructions
Recycling – the packaging materials
for this product may be recycled
through your local recycling centre.
When you want to dispose of the
product itself, please consider
donating it to a local charitable
organisation, otherwise recycle it
through your local recycling centre.
CLEANING INSTRUCTIONS
This product has been manufactured using
modern manufacturing methods and
materials. With appropriate in-home care
and maintenance it will provide trouble free
performances. Many domestic multi-
purpose cleaning agents are unsuitable for
use on this product. The use of aggressive
chemicals can result in irreversible
damage. Please follow these guidelines
carefully.
USE only 5% soap, 95% water solution,
wiping with a damp (not wet) cloth. Finally
dry with a soft clean cloth. Dust with a soft
clean cloth only.
DO NOT USE wax furniture polish, abra-
sive or aggressive cleaners, bleach or
hypochlorate (chlorine) based cleaners,
multi-purpose cleaners, dilutes, acetone,
alcohol, solvent or similar products.
That's the internal 3 drawer chest completed.
Take care of your unit by using a damp cloth to clean it.
Please remember to occasionally check that all Cams
and Screws are tight.
11