Schreiber Messtechnik Kew-Full Display User manual

Kew - Full Display
Dimensions
Width - 89.6cm
Depth - 45.1cm
Height - 197.2cm
BK00410 - Issue 1 - 31/03/2010
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 2417621
Assembly Instructions - Please keep for future reference 613/9298

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Due to difference in floor
levels, doors may not be
aligned. Adjustment may be
necessary.
• Do not use extended drawers
to aid standing. Do not stand on
extended drawers.
• Do not over load drawers,
the maximum load per drawer
should not exceed 3kg.
• To prevent bowing of shelves
do not over load, and always
distribute weight evenly.
• If a residual aroma is
experienced with your new
furniture after the packaging
is removed simply ensure the
room is well ventilated and this
will assist a speedy removal
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• It is essential that this unit be
fixed to a wall with the fittings
provided.
• Please retain the product label
on the back of the unit, as this
information will help support any
queries.
• Dust with a clean cloth or, if
required a slightly damp cool
cloth. Do not use household
cleaners, abrasives or polishes
as permanent damage may
occur.
• Your furniture is finished to the
required colour. Avoid exposure
to strong sunlight as this can
change the colour. Change in
appearence may also occur if
items are permanently left on a
surface.
• Do not drag the furniture or lift
it by its top.
• Avoid sharp objects, contact
with water and direct heat on all
surfaces
• From time to time check that
there are no loose screws on
this unit.
• You should get assistance
when moving or lifting your
furniture. Furniture consisting of
more than one unit should be
disassembled before attempting
to move it.
• Doors and drawers should
be secured or removed before
moving.
• Electrical fittings must be fitted
with a 3-amp fuse to BS1362.
Disconnect from the source of
power before changing bulbs.
Replace bulbs with the same
type and wattage.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance - Non compliance with this information may affect your guarantee

Components - Panels
Please check you have all the panels listed below
2
Dispaly unit (197.2 x 89.6 x 45.1cm)
1
If you have damaged or missing components,
call the Customer Helpline:
0845 2417621

3
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
Tools required
AB C
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
D
Socket adapter x1
Components - Fittings
Phillips screwdriver
(medium)
15mm Screw x 1 15mm Washer x 2 Wall strap x 1
The following components are pre-fitted and are illustrated for reference only.
Display light [with bulb] x 1
Step Ladder
(or equivalent)
Cup handle x 2 20mm Handle screw x 6Oval handle x 2

4
Assembly Instructions
Step 1 a:
Philips screwdriver
1
Remove and replace
handle
a: Position the unit in the
required position. The
cup and oval handles
are fitted to the inside of
the unit, using a Philips
screwdriver unscrew the
20mm handle screws in
each handle and remove
both the 20mm handle
screw and the cup and
oval handle.
b: Replace the cup and
oval handle on the front
of the unit. Fix in position
by screwing the 20mm
handle screw into each
cup and oval handle from
inside the unit using a
Philips screwdriver.
b:
20mm Handle screw
Philips screwdriver
20mm Handle screw
Oval handle
Cup handle

Assembly Instructions
Step 2
b: Connect the socket
on the display light in the
connection on the socket
adapter D. you can now
connect to the mains.
Note: the light display
light fitting has is own on
/ off switch on the back of
the fitting
Warning:
Always turn the
lights of at the
mains when changing the
bulb.
5
D
conection from display light
b:
a:
conection from display light
1
Conecting display
lights
a: The display light is
fixed to the light pelmet
inside the display
cabinet. Push the the
fitting on the end of the
cable through the hole in
the back panel.

Step 4
Assembly Instructions
Adjusting doors
1. To adjust the height /
level of the door loosen
all screw ‘A’s on all hinge
plates, level the door
height and retighten all
screw ‘A’s.
2. To adjust the gap
between the doors
loosen screw ‘B’, then
turn screw ‘C’ clockwise
to close the gap or
anticlockwise to increase
the gap. Re-tighten
screw ‘B’ to lock position.
3. To adjust the distance
away from the unit
loosen screw ‘B’, this
allows the hinge arm
to slide back and forth.
Adjust as required then
re-tighten screw ‘B’.
Assembly is complete.
A
A
B
C
2
1
3
Step 4
Fixing to wall
It is recommended that
the unit is fixed to a wall
Fix wall strap Cto the
back of the unit using
15mm screw Aand
15mm washer B.
Warning: The
15mm screw A
is for fixing the
wall strap Cto furniture
only. In addition to this
you will need to choose
a screw or fitting which is
suitable for securing the
wall strap Cto the type
of walls you have. If you
are unsure about what
type of screw to use seek
professional help.
CUsing the correct type of
screw, screw through the
washer and wall strap
into a pre-drilled hole in
the wall
Back Panel
Unit Top
A
B

If you need help or have damaged or missing parts, call the Customer Helpline: 0845 2417621