Schweigen UM1170-6S User manual

RANGEHOOD INSTRUCTIONS GUIDE
UM1170-6S, UM1170-9S, DS3131S, DS3170-12S, DS3170S,
WM3150S, WM3150-6S, WM2190S, WM2190-6S
HOME APPLIANCES

Page 2
INTRODUCTION OF DEVICE
DS3131S
262
250
500
900
84
Min 662, Max 1190
WM2190S, WM2190-6S
252
260
600,900
500
28
118
Min 698 Max 1190
245
199
268
295
530 / 790
500 / 750
238
135
30
30
UM1170-6S, UM1170-9S

Page 3
DS3170-12S, DS3170S
900, 1200
500
262
250
60
Min 638 Max 1190
WM3150S, WM3150-6S
262
250
60/47
600/460
900/600
Min (90) 780/ (60) 767 Max (90) 1190 (60) 1190
410
500

Page 4
SAFETY PRECAUTIONS INFORMATION
• This product is designed for home usage.
• If you notice any damage please report to the seller before installation.
• Your products usage voltage is 220-240 Volts ~ 50Hz.
• Plug into the socket and test before installation of the product male plug is mains power
female is to go to ISO Drive Motor
• Best to turn on the rangehood before commencing cooking.
• Yourproductmaycausereriskifcleaningisnotappliedperiodically.
Accessories
Flexi Ducting
Picture 1a Picture 1b Picture 2
After installation of your product, the distance between
rangehood and electrical hob should be min 65cm and gas
should be min 75cm.
Reducer (Picture 1a) is for use when using 150mm ducting and is placed on 200mm opening
on top of canopy see (Picture 1b). Picture 2 shows how it should look.
Donotcrushexiducting.
Product Placement

Page 5
Picture 3
Picture 4
Mounting holes for model UM1170-6S
Mounting holes for Model UM1170-9S
Place the hood into the cabinet (Picture 3), align holes in the
undermount to the pre-marked or drilled holes in the cabinet
totheholesontheundermountandxintoposition.(Picture4)
UNDERMOUNTS
Fix the undermount to the cabinet

Page 6
Assembling Tempered Glass (This process is only applied for models WM3150S and WM3150-6S)
Assemble the tempered glass supplied with the hood ensuring that it is placed on the hood
body. Fix glass to the body by screwing the screws in holes placed on the hood and the glass.
Placement of hanging screws
L formed hanging plates
Connect L formed hanging plates to the canopy
Attach mounting template to the wall where the chimney hood will be installed. Drill A, B, C
(D see Figure 1 Part B) points by using Ø 8mm. For screwing chimney montage plate, drill Ø
6mm holes, consider the minimum and maximum length of product. (Figure 1)
170mm
C
H670.1000.01
MOUNTING TEMPLATE SCALE 1:1
min.650-max.750mm min.750-max.800mm
WORKTOP
ELECTRO GAS
B
A
170
A,B,C = Ø8
Figure 1 Part A: WM3150S, DS3131S, WM2190S
WALL UNIT
Picture 5

Page 7
Optional Plug Insertion
For suspension screw, insert Ø 8mm plugs into drilled holes (A,
B, C). For chimney mounting sheet, insert 2 dowels of Ø 6mm
into holes drilled by using Ø 6mm. (Picture 6)
Screwing of suspension screws
Screw suspension into Ø 8mm dowels (A, B) inserted into the
wall by using 5.5 x 45 screws. There should be 5mm interval
between wall and the screw head. (Picture 7)
A B
CD
A,B,C,D = Ø8
MOUNTING TEMPLATE SCALE 1:1
B
A
170
min.650-max.750mm min.750-max.800mm
WORKTOP
ELECTRO GAS
H670.3120.02
680
345,5
170mm
Figure 1 Part B: DS3170S
Picture 6
Picture 7
Installation of chimney hood
Lift the chimney hood and connect L formed hanging plates
which are on hood cabin to A, B points on wall. (Picture 8)
Picture 8

Page 8
Screw chimney wall bracket
Screw chimney montage plate to 6mm wall plugs by using
3.9 x 22 screw that are supplied. (Picture 12)
Wall Bracket
Internal
External
Range Hood
Tighten the screws
After completing the hanging, tighten the screws by using a
screwdriver, to prevent the remove of the product. (Picture 9)
Screw rangehood onto wall
Whenxingiscompletedscrewtherangehoodontowall
from C point which is inside of the body. (Picture 11)
Point C
Inclination
If there is inclination, soften screws on top and correct
parallelism. (Picture 10)
Picture 9
Picture 10
Picture 11
Picture 12

Page 9
Install chimney
Install chimney around the body. (Picture 14)
Installation of aluminium duct
Connectaluminiumexibleductonplasticoutletandfeed
through hole in ceiling. (Picture 13)
Picture 13
Picture 14
Picture 15
Fix the chimney internal cover to the wall
Screw the inner hood in to the chimney mounting bracket
whichisxedtowallfromitsupperoutersides.(Picture15)
Replacing the lamps
Cut off the connection of the rangehood with electricity.
Takeoffthemetalcassettelter.Takeoutthefailedlapand
replace it with a new one that is of the same rating. Note:
Please wait for the lamps to cool as they might hurt your hand.
Replace with 35W halogen lamp or 1.8W to 4.5W LED
In order to change halogen lamps, take the lamp downwards
pushing the back of lamp holder downwards and then turning
it a little bit anti-clockwise taking it off downwards. (Figure 2)
Please Note: Lights are not covered by warranty.
MAINTENANCE
Figure 2

Page 10
USAGE
Remove protective foil on your stainless steel product after installation before usage.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Blue light canopy (DS3131S) model:
Press and hold lamp button for 3 to 4 seconds to turn blue light on and off.
Note: Light globes and fuse are not covered by warranty (They can be purchased from your
local lighting store)
Speed Selection
This product has 5 speed of ventilation level. One of 1, 2, 3/4, 5 speeds is selected in
accordance with steam of cooking or fry. Motor is started pressing control button on the
front panel. Speed is increased pressing “+” button, and decreased by pressing “-” button.
Timer
When pressed to button more than 2 seconds, timer function will be activated for 15
minutes and timer sign will appear on screen. Motor will stop automatically after 15 minutes.
• Disconnect electricity connection before maintenance
and cleaning process.
• Metalcassettelterholdsthedustandtheoilintheair.
• Metalltershouldbewashedregularly(pleasesee
“Cleaningperiodsofmetallters”)andsoapedwateror,if
possible, with a dishwasher (60°C).
• Takeoffmetalcassettelterpressingonspringylatcheson
end point. After cleaning, do not replace before it dries.
• Outer surface of the rangehood should be wiped down
with a wet cloth, water or alcohol can be used.
• Please avoid contact of electronic parts with water or
similar materials.
• Using stainless steel cleaning and maintenance products
available in the market will help your product to
perform longer.
• Warning: Filters may be washed in the dishwasher. Colour
ofthemetalltersmaychangeafterseveralwashes.Thisis
normalanditisnotnecessarytochangethelters.
Picture 16
Picture 17
Washable cassette lters

Page 11
Inordertousetherangehoodefciently:
• Payattentiontometallters’cleaningperiods.
• Use the product at middle speed if high suction power is not necessary.
• In order to ensure that ventilation occurs correctly, windows of the kitchen should be kept closed.
TECHNICAL SPECIFICATIONS
Model 3170, 3131, 2190, 3150
Feeding Voltage 220-240V 50Hz
Lamp Power (W) 2 x 35W
If the product does not work:
Before you contact the technical service, make sure that the product is plugged in and the
electric fuse is in and electric wiring is connected. (Fuses can be purchased from your local
electrical dealer or hardware store) Do not take any action that will damage the product.
Check your rangehood according to the table below, if the problem goes on, contact the
seller or the authorised service.
PLEASE NOTE:
If a call out is requested and it is found there is no manufacturing fault and/or relating to
incorrect installation even during the warranty period, this will result in a service fee directed
tothecustomer.Incorrectinstallationmayreduceairoworincreasenoiselevels.Schweigen
will take no responsibility for problems caused by faulty installation. Installation should be
donebyaqualiedtechnician.ApreferredinstallerlistcanbeobtainedfromSchweigen
website www.schweigen.com.au.
Cleaningperiodsofmetallters—“C”Signal
Filter should be cleaned when “C” signal appears on the display about 4 to 5 weeks (or in
accordancewiththeusagefrequency).Inordertoremove“C”signal,aftertheltersare
cleaned and placed back to their place, press button for more than 3 seconds, when the
product is at off position. The Letter “E” will appear on display and the product will operate as
normal.
If you would like to continue using the product without deleting “C” signal, when you press
the button active speed will appear for 1 second, then “C” signal will appear once more
and the motor will continue operating. Note:“C”signalwillappearafteryouusetheproduct
for 60 hours.

Check electric connection (Voltage of the electric network should be between 220 - 240V, rangehood should be connected to grounded plug.) Check motor switch (Motor switch should be at on position) Check lamp switch (Lamp switch should be at on position) Checkmetallter(Metal cassetteltershouldbewashed once a month at normal conditions.) Check lamps (Lamps should berm) Check outlet (Outlet should be open) Check fuse inside rangehood (1.5 - 2amps / 250V)
Rangehood does not work X X
Light does not work X X X X
Rangehood air suction is weak X X
Rangehood does not direct air out
(at places without chimney) X
CONDITIONS
1. This warranty applies to domestic use of the appliance only.
2. Under warranty if damage should occur by misuse or negligence to: Gloss removable,
plastic parts, varnished & enamelled parts, exchange will not be free of charge.
3. Provided warranty labour will be carried out during normal hours and by Schweigen
Home Appliances or its approved designated service agent, the labour provided, will be
free of charge.
4. This warranty is invalid if on inspection the fault is due to lack of cleaning or general lack
of care for that particular unit or is installed incorrectly.
5. This warranty is invalid where it is established on the service call there has been neglect or
misuse to the unit.
6. This warranty is invalid if there is no proof of purchase.
7. Where it is established that the unit has been used for purposes other than that to which it
is designed for.
8. Please note that the light globe is not covered under this warranty.
9. Customers outside normal service districts will be responsible for transport to and from the
service agent or the service agents travelling cost to customer.
10. Customers must ensure the appliance is accessible otherwise a charge may be incurred.
11. This warranty may become null and void if the appliance has not been installed
andusedinaccordancewithourinstruction,orifanyunauthorisedmodicationsor
alterations have been performed to the appliance.
12. Model and serial numbers must not be removed or altered in any way.
13. If used for commercial, industrial, multiple family use or other non-domestic purposes,
warranty and free service will only be by negotiation with Schweigen Home Appliances.