SCS S-1 User manual

SCS S-1
www.scssa.co.za

1.Outlook / Function
..............................................................................................................1
2.Device Pairing
................................................ ..........................................................2-5
3.Group Intercom Mode Pairing (Operating Scenario)
.........................................................................................................6-10
4.Q&A / Warning
............................................................................................................11
5.Statement / Warranty
.......................................................................................................11-12
Contents:

1. Outlook / Function
01
Switch On / OFF
Switch On: When device is off, press
intercom+function at same time for 3 seconds.
Switch Off: When device is on, press
intercom+function at same time for 3 seconds.
*For first time use, please recharge the device
until the red light is off.
Cellphone Function
Answering Call: Short press function once.
Hang up Call: After call, short press function
once.Refuse Call: Long press function button
for 2 seconds.Redial: Short press function
button twice.
Volume Up: Press Volume + while talking.
Volume Down: Press Volume - while talking.
Power Detect & Notification Function
Low Power Notification: When power lower
than 10%, red light flash in the function button
and voice message will remind power lower
than 10%, please recharge immediately.
Power Detect Function:S-1 has power detect
function , when device is on , short press
volume - and volume + button at the same
time , recorded voice message will tell you :
Power over 90%
Power over 50%
Power lower than 50%
Power lower than 10% please recharge
immediately
Voice Command
When your S-1 is paired up , short press
function button once , will automatically
switch on the voice command function .
*Cellphone must equipped with this function.
Memory Clear
Memory Clear: When device is on, press
Volume + and function button at the same
time for 5 seconds. Then S-1 will clear the
pairing memory with other devices.
Intercom Function
Switch Intercom On: When device on, short press
intercom button once.Switch intercom off: When
talking, short press intercom button once.Volume
Up: When talking, short press Volume + once.
Volume Down: When talking, short press
volume - once.
Music Function
Play: When device is on, short press volume +
twice.Pause: When music is playing, short press
volume + twice.Volume Up: When music playing,
short press volume + once.Volume Down: When
music playing, short press volume - once.Play
Previous: When music playing, long press
volume + for 2 seconds.Play Next: When music
playing, long press volume - for 2 seconds.


/ microphone Jack
+
-

/ Data Jack

2.1 Pair Up to Bluetooth Devices
2.1.1 Pairing Mode
2. Device Pairing
02
When device is on. Long press function button
Pairing mode, red and blue light flash,
voice message says pairing.

2.1.2 Search Mode
When device is on. Long press intercom button
Search Mode, Red and blue lights flash quickly
03

2.2 Pairing With Cellphone
04
When device is on, long press function button
Switch cellphone Bluetooth, choose S-1, the pairing is complete. Voice message will also say
pairing complete.
Remark: when pairing complete, please check both cellphone audio and media audio
are all chosen, otherwise call or music can not be processed.
red and blue light flash in the function
button, entering pairing mode
SCS-S1
04

04
Long press volume + and Volume - for 3 seconds
Any device with 3.5mm connector can transmit voice signal to S-1.
When device wire connected by 2.5mm to 3.5mm cable to S-1 , long press the volume + and
volume - at the same time for 3 seconds to switch on the connection .
*When wire d mode is switched on, it will keep it on until switch off the S-1.
2.3 Cable Connecting
05
05

06
At first of all , pair up GPS and cellphone
Pair up S-1 with GPS , after paired , please switch off the Bluetooth function in GPS
Lastly, pair up S-1 with speed detector, after paired, switch on GPS Bluetooth function
*S-1 paired with GPS, if don’t switch GPS Bluetooth function, it will interference the pairing
when pairing to speed detector. Recommended to switch GPS Bluetooth off, after pair up
to speed detector, switch the Bluetooth back on.
3. Group Intercom Mode Pairing (Operating Scenario 1)
3.1 Operating Scenario 2:Two person intercom , and pairing to cellphone + Bluetooth GPS

07
3.2 Operating Scenario 2: Two person intercom, and
pairing to cellphone + Bluetooth
GPS + speed detector or radio
Pairing Procedure:
Step 1: Switch A to search mode (details to 2.1.2), B to pairing mode (details to 2.1.1) .
when both headset stop blue and red light flashes, they are paired.
Step 2: Switch A to pairing mode (details to 2.1.1), cellphone search this A and pair it up.
Step 3: Keep A in pairing mode (details to 2.1.1), use Bluetooth GPS to search A and pair it up.
Step 4:Use 2.5mm to 3.5mm AUX in cable to connect speed detector or radio to S-1 ,
and switch S-1 to wire connecting (details to 2.3 ) , all audio inter-grade are completed .
*Switch on intercom, both rider and passenger can hear audio from GPS, speed detector or radio.
if rider gets an incoming call , device will cut off the intercom .when rider’s call is finished ,
device will reconnect automatically .

08
3.3 Operating Scenario 3: Two person intercom, rider
using cellphone + Bluetooth GPS, passenger
use Bluetooth speed detector.
Pairing Procedure:
Step 1: Switch A to search mode (details to 2.1.2), B to pairing mode (details to 2.1.1)
.when both headset stop blue and red light flashes, they are paired .at same time
instantly switch intercom.
Step 2: Switch A to pairing mode (details to 2.1.1), cellphone search this S-1 and pair it up.
Step 3: Keep A in pairing mode (details to 2.1.1), use Bluetooth GPS to search A and pair it up.
Step 4: Set B to pairing mode (details to 2.1.1), use Bluetooth speed detector to search B and
pair up.
*When both headsets are switched off, and rider or passenger wants to reconnect, please press
rider’s intercom button to reconnect and will be able to share all audio source again.
Rider Headset A Passenger Headset B