Sea & Sea 31135 User manual

Instruction Manual
(Current as of JAN. 2009)
0825-Z-01
SEA&SEA SUNPAK Co., Ltd.
3-2-20, Saiwai-cho, Kawaguchi-shi, Saitama, Japan 332-0016 TEL. [phone]
World Customer Service Center TEL. [phone]
* The specifications and appearance are subject to change without notice.
Construction Corrosion-resistant aluminum alloy Dimension (DIA×D) Approx. 88×76mm / 3.5×3inch
Weight Approx. 158g / 5.53oz Accessories Gear sheet (stick-on), O-ring, Instruction Manual
31135
http://www.seaandsea.jp
Specifications
AF-S Micro NIKKOR 60mm F2.8G ED Focus Gear
Fig.1
Fig.2
Focus Gear Lens
Camera mount side
Focus Gear
Lens
Failure to heed the precautions listed below could result in serious consequences. To prevent injury or damage to yourself and/or others, please
observe the precautions as they contain highly important information related to personal and product safety.
Situations that could result in property damage or personal injury.
CAUTION
Precautions
Thank you for purchasing SEA&SEA products. Please read this instruction manual carefully prior to using this product. Only with a
thorough understanding of this manual’s content will you be able to use the product correctly. After reading the manual, please be sure to
keep it in a place where you can easily come back to it at any time.
CAUTION
Carefully observe the instruction manual for the compatible lens for this
product before use.
This product includes an O-ring (divided into pieces) for interlocking the
lens and the gear. In some cases, the interlocking may be too tight or
loose when attaching the gear, due to deviation in the lens diameter.
①When too tight
Remove all of the O-ring pieces from inside the gear and cut them
shorter with scissors. Re-insert these pieces into the grooves inside
the gear, providing ample space between the pieces. Adjust the length
of the O-ring pieces for appropriate tightness.
* Do not force the lens into the gear when the interlocking is too tight,
because this may result in damage to the lens.
② When too loose
Replace the O-ring with the thicker O-ring that was also supplied with
this product. If it becomes too tight with the thicker O-ring, adjust the
interlocking tightness as explained above ①. If it is still too loose, use
the gear sheet which is included in the package. Cut the sheet into 3
to 6 pieces with scissors, and apply them between the grooves inside
the gear.
* The thicker O-ring may not be compatible with some lenses due to
size restrictions. In this case, adjust the tightness by following the
above procedure ① and using the gear sheet included in the
package.
Always make sure that the gear and the lens work properly after
adjustment.
SEA&SEA SUNPAK Co., Ltd. will not be responsible for the replacement
or compensation for cameras, lenses or those accessories damaged due
to your invalid operation.
SEA&SEA SUNPAK Co., Ltd. assumes no liability for compensation of
loss of captured images or expenses caused by loss of images, even if
you are unable to shoot due to a product defect or malfunction.
SEA&SEA SUNPAK Co., Ltd. assumes no liability for errors or
discrepancies in this manual.
This product is designed for manual-focus operation possible utilizing the focus/zoom dial on SEA&SEA digital SLR camera housings.
How to Attach to the Lens
Focus Gear
Ensure that the O-ring pieces inside the gear do not come out of the
grooves when detaching the gear from the lens.
CAUTION
Make sure to set the lens to manual focus mode.
CAUTION
Push the gear down as far as it will go. (Fig.2)
Refer to the lens instruction manual for setting of the A-M mode
switch.
Set the A-M mode switch on the lens to "M" position
1
Attach this product to the lens in parallel alignment
with the lens as shown in Fig.1
2
Refer to the housing instruction manual for mounting the camera in
the housing.
After mounting the camera in the housing, always try operating the
focus/zoom dial on the housing to make sure that the lens works
smoothly and properly with the gear attached. If the gear is not
properly attached to the lens or is out of parallel alignment, the
manual-focus operation may not work properly.
Mount the lens, with the gear attached, to the camera,
and then mount the camera in the housing
3