SeaLand 711-M28 User manual

1
OWNER’S MANUAL
711-M28
MARINE TRAVELER®TOILET
Dometic Corporation
13128 State Rt 226, PO Box 38, Big Prairie, Ohio 44611-0038 U.S.A.
SeaLand Product Hotline [phone]
(8:00 a.m. - 5:00 p.m. ET)

2
RECOMMENDATIONS
SPECIFICATIONS
Product Name: 711-M28 Marine Traveler Toilet
Shipping Information:
Carton Sizes:
Toilet 21" x 18-1/2" x 13-1/2"
(533mm x 470mm x 343mm)
Tank 19-1/4" x 17-1/2" x 11-1/2"
(489mm x 445mm x 292mm)
Weight Approx. 49 lbs. (22Kg)
System:
Average water consumption per flush 1 Qt. (.95 L)
Minimum water consumption per flush 1 Pt. (.47L)
Holding tank capacity . . . . . . . . . . . 9.5 Gal. (36L)
Fresh water supply pressure . . . . . . . . . . 5-80 PSI
Water inlet size . . . . . . . . . . . . . . . . . . . 1/2" NPT
Holding tank discharge fitting . . . . . . . 1-1/2" NPT
Vent fitting . . . . . . . . . . . . . . . . . . . . . . 5/8" Barb
Unit Weight . . . . . . . . . . . . . . . . . 41 Lbs. (19Kg)
Dimensions:
1. Read the “Operating Instructions” section of the
manual carefully.
2. Make sure all guests understand the operation of
the Traveler toilet.
3. Carry a few spare parts for the maintenance purposes.
SeaLand has developed several repair kits that will
save you both time and expense should a problem
occur. See “Customer Service” section of this manual.
4. Use only SeaLand brand®Tissue and Secure®
liquid or SeaLand®brand Holding Tank Deodorants
to maintain a trouble-free system.
5. Do not use chlorine or caustic chemicals, such as
laundry bleach or drain opening types, in the
system. These products damage the seals in toilets.
6. Do not flush foreign objects through the toilet.
7. Do not allow small problems to go unsolved. As soon
as a problem is detected, correct it.
INSTALLATION INSTRUCTIONS
Tank:
1. Select position in bathroom where unit can operate
properly. Allow room for using the flush lever and
clearance for raising the seat and lid.
2. Position the tank 3/4" (19mm) away from the wall.
Mark four holes at mounts on tank base. After holes
are marked, remove tank, and drill pilot holes. Slide
tank back into position. Secure the tank with four
#14 x 2" long pan head screws and washers on all
tank mounts.
3. Run 5/8" (16mm) I.D. hose to vent fitting and secure
with hose clamps.
Install thru-hull vent fitting:
(not supplied with unit – SeaLand part number 346368)
4. Drill hole through the hull, well above water line and
directly above Traveler toilet. Hole location is deter-
mined by routing and length of hose.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 2
Recommendations . . . . . . . . . . . . . . . . . . . . 2
Installation Instructions . . . . . . . . . . . . . 2 - 4
Operating Instructions . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . . 4 - 5
Preparing for Summer Use . . . . . . . . . . . . . 5
Model Identification . . . . . . . . . . . . . . . . . . . 5
Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . 5
Customer Service . . . . . . . . . . . . . . . . . . . . 5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Troubleshooting Guide . . . . . . . . . . . . . . . . 7
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3
5. Apply waterproof caulk around underside of thru-hull
vent fitting.
6. Install thru-hull vent fitting and secure snugly with nut.
Wipe off excess caulk with damp cloth.
7. Attach remaining end of vent hose to thru-hull
fitting with hose clamp.
Dockside Discharge Fitting:
(not supplied by SeaLand)
8. Drill hole in deck directly above Traveler toilet. Hole
location is determined by routing space and length of
hose.
9. Screw 1-1/2" FPT x 1-1/2" hose barb into bottom of
deck fitting.
10. Apply waterproof caulk around deck hole and install
deck fitting into 2-1/4" (57mm) hole with screws. Wipe
off excess caulk with a damp cloth.
11. Install 1-1/2" MPT x HUB adapter into discharge fit-
ting on holding tank.If necessary, PVC cement el-
bow and hose adapter or hose adapter only into
1-1/2" (38mm) adapter. Secure 1-1/2" (38mm) hose
to adapter with hose clamp.
12. Route hose from tank to deck fitting and secure with
hose clamp.
Note: The holding tank on the 711-M28 is designed
to withstand discharge by a properly operating
discharge pump.
Toilet Installation:
13. Push button on back of flush pedal, then pull flush
pedal cover away from pedal to expose water valve.
Remove plastic pedestal cover from toilet base.
14. Install the (4) 1/4-20 x 1-3/4" long studs in inserts on
the tank top.
15. Place floor flange seal on studs, aligning the studs
with bumps on seat. Note: “THIS SIDE UP” should
face upwards.
16. Place toilet on studs and secure with four washers
and four nuts.
INSTALLATION INSTRUCTIONS (cont’d)
or

4
INSTALLATION INSTRUCTIONS (cont'd)
Water line:
17. Locate water valve at rear of flush lever.
18. Attach water supply pipe or hose from water system
to inlet fitting on back of water valve.
Pedestal cover:
19. Slide back side of pedestal cover around rear of toi-
let base and snap in groove. Close front half of ped-
estal cover and snap in groove.
Flush pedal cover:
20. Put flush pedal cover back in place.
Seat and lid:
21. Remove seat and lid from package. Secure to china
bowl using instructions from mounting pack.
OPERATING INSTRUCTIONS
To properly use the Traveler®toilet, follow these simple
instructions:
1. A good biodegradable tissue such as SeaLand®brand
is recommended.
2. To add water to the toilet before using, lift or raise
the flush pedal.
3. To flush toilet, push pedal all the way down until
sewage leaves the toilet bowl. Water flow pressures
vary at different locations and therefore, holding the
flush lever down 4-8 seconds may be required. We
recommend 2-4 GPM (8-15 Lpm) for proper rim and
bowl wash.
4. Release flush pedal by allowing it to snap back, which
permits positive sealing around the flush ball.
5. A small amount of water should remain in the bowl.
Note: Holding the flush pedal down longer than neces-
sary results in excessive water usage.
CAUTION: Do not dispose of sanitary napkins or other
non-dissolving items in the toilet.
MAINTENANCE
CLEANING
The Traveler toilet should be cleaned regularly for maxi-
mum sanitation and operational efficiency.
Clean the toilet bowl with a mild bathroom cleaner, such
as SeaLand’s Brilliance™ thick liquid toilet bowl cleanser.
Do not use chlorine or alcohol-based caustic chemicals
such as drain opening types, as they will damage the
seals.
If an odor is apparent from the toilet:
1. Clean out system by flushing several gallons of fresh
water through with one cup of dry laundry soap.
2. Add odor control deodorant in amount specified for
your holding tank capacity after cleaning and every
few days during use.
WINTERIZING
At the end of each season, the Traveler toilet should be
winterized for storage by either draining or using potable
water safe antifreeze in the system.
To drain:
1. Thoroughly flush system with fresh water.
2. Empty holding tank.
3. Shut off water supply to toilet. Remove inlet
waterline.
4. Press flush lever until all water is drained from toilet.

5
To use antifreeze:
1. Thoroughly flush system with fresh water.
2. Empty holding tank.
3. Drain potable water tank.
4. Add freshwater antifreeze and water mixture
through toilet and into the waste holding tank. Each
installation is different, so amounts may vary. User
discretion is required to assure adequate protection.
5. Empty holding tank.
Note: Use nontoxic antifreeze designated for potable
water systems (see boat owner’s manual).
CAUTION: Never use automotive-type antifreeze in
freshwater systems.
PREPARING FOR SUMMER USE
To prepare the Traveler toilet for summer use, turn on
water supply and check system for leaks. Flush toilet,
check for leaks and repair as necessary. Your Traveler
toilet is now ready for use.
MAINTENANCE (cont’d)
SeaLand has a strong, worldwide network to assist in
servicing and maintaining your Traveler toilet if parts or
service are required. Before calling, please have the
following information available. Your cooperation in hav-
ing this information ready is appreciated and allows our
Customer Service Department to better meet your needs.
When you call, we will direct you to the nearest parts
distributor.
1. Toilet Model Number
2. Serial Number
3. Part Number, Description and Quantity (See Parts List.)
When you have gathered all the required information,
call us at one of the following telephone numbers from
8:00 a.m. to 5:00 p.m. (Eastern Time) Monday through
Friday, or email us.
Telephone: [phone] USA and Canada
330-496-3211 International
Fax: [phone] USA and Canada
330-496-3220 International
Email: [email protected]
CUSTOMER SERVICE
U.S.A. - Southeast
(AL, FL, GA, NC, PR, SC, TN, VI)
Environmental Marine
111 S.W. 23rd Street, Suite A
Fort Lauderdale, FL 33315
Tel: [phone]
800-522-2656
E-mail: [email protected]
U.S.A. - Southwest
(AZ, CO, NV, UT, CA-south)
Ardemco Marine Specialties
778 West 17th Street
Costa Mesa, CA 92627
Tel: [phone]
800-253-0115
E-mail: [email protected]
U.S.A. – Upper Midwest
(IA, MN, NE, ND, WI, SD)
PowerHouse Marine
518 Logan
La Crosse, WI 54603
Tel: [phone]
888-752-4539
E-mail: [email protected]
U.S.A. – Northern California
Fox Marine
2250 Zanker Road, Unit D
San Jose, CA 95131
Tel: [phone]
800-826-2873
E-mail: [email protected]
Canada - East
Eastern Marine Systems, Inc.
12-A Leslie Street
Toronto, Ontario M4M 3H7
Tel: [phone]
888-764-1111
E-mail: [email protected]
Canada - West
Western Marine Company
1494 Powell Street
Vancouver, BC V5L 5B5
Tel: [phone]
800-663-0600
E-mail: [email protected]
MASTER SANITATION
DISTRIBUTORS –
NORTH AMERICA
U.S.A. – North Central
(IL, IN, KY, MI, OH)
Midwest Marine Supply
24300 Jefferson Ave.
St. Clair Shores, MI 48080
Tel: [phone]
800-860-1540
E-mail: [e-mail]
U.S.A. - Northeast
(CT, DE, DC, MA, MD, ME, NH, NJ, NY, PA,
RI, VA, VT, WV)
Northeast Marine Sanitation
69 Florida Street
Farmingdale, NY 11735
Tel: [phone]
800-352-4323
E-mail: northeast
@northeastsanitation.com
U.S.A. - Northwest
(AK, ID, MT, OR, WA, WY)
Marine Sanitation, Inc.
1900 N.Northlake Way,Suite 121
Seattle, WA 98103
Tel: [phone]
800-624-9111
E-mail: [email protected]
U.S.A. - South Central
(AR, KS, LA, MO, MS, NM, OK, TX)
AER Supply
P.O. Box 349
2301 Nasa Road #1
Seabrook, TX 77586
Tel: [phone]
800-767-7606
E-mail: [email protected]
MODEL IDENTIFICATION
SPARE PARTS
The model identification label is located on the inside of
the flush pedal cover.
Your 711-M28 Traveler toilet is designed for years of
dependable trouble free service. However, during the
life of the product certain parts may require replacement.
The following is a list of parts kits which may be required
for maintenance purposes.
Part Number Description
318162 Ball, Shaft & Cartridge Kit
316140 Seal Kit
314349 Water Valve Kit
316906 Vacuum Breaker Kit
DOMETIC CORPORATION
P.O. BOX 38, 13128 STATE RT 226 [phone]
BIG PRAIRIE, OH 44611 USA
MODEL NO. 000
SERIAL NUMBER
000000