SeaLevel SeaLINK DIO-16 User manual

[phone] | [email protected] | artisantg.com
-~
ARTISAN
®
~I
TECHNOLOGY
GROUP
Your definitive source
for
quality
pre-owned
equipment.
Artisan Technology
Group
Full-service,
independent
repair
center
with
experienced
engineers
and
technicians
on staff.
We
buy
your
excess,
underutilized,
and
idle
equipment
along
with
credit
for
buybacks
and
trade-ins
.
Custom
engineering
so
your
equipment
works
exactly as
you
specify.
•
Critical
and
expedited
services
•
Leasing
/
Rentals/
Demos
• In
stock/
Ready-to-ship
•
!TAR-certified
secure
asset
solutions
Expert
team
ITrust
guarantee
I
100%
satisfaction
All
tr
ademarks,
br
a
nd
names, a
nd
br
a
nd
s a
pp
earing here
in
are
th
e property of
th
e
ir
r
es
pecti
ve
ow
ner
s.
Find the Sealevel Systems DIO-16 at our website: Click HERE

www.sealevel.com PO Box 830 Liberty, SC 29657 864.843.4343
SeaLINK DIO-16 User Manual
Part Number 8209
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc.
SL9017 Revision 7/2006 SEALINKDIO-16UserManual
Table of Contents
INTRODUCTION......................................................................................................................... 1
OTHER SEALEVEL USB DIGITAL I/O PRODUCTS......................................................................... 1
BEFORE YOU GET STARTED................................................................................................. 2
WHAT’S INCLUDED...................................................................................................................... 2
OPTIONAL ITEMS.......................................................................................................................... 2
SOFTWARE INSTALLATION.................................................................................................. 3
WINDOWS 98/ME/2000/XP INSTALLATION................................................................................. 3
PHYSICAL INSTALLATION.................................................................................................... 4
PROGRAMMING THE SEALINK DIO-16.............................................................................. 5
PROGRAMMING FOR WINDOWS.................................................................................................... 5
DIGITAL I/O INTERFACE .............................................................................................................. 5
SERIAL STRING ............................................................................................................................ 5
INPUT PORT.................................................................................................................................. 6
OUTPUT PORTS (REED RELAYS) .................................................................................................. 6
PIN ASSIGNMENTS (REMOVABLE TERMINAL BLOCK).................................................................. 7
ELECTRICAL CHARACTERISTICS...................................................................................... 8
FEATURES.................................................................................................................................... 8
SPECIFICATIONS........................................................................................................................... 8
EXAMPLE CIRCUITS................................................................................................................9
APPENDIX A - TROUBLESHOOTING ................................................................................. 10
APPENDIX B - HOW TO GET ASSISTANCE ...................................................................... 11
APPENDIX C – SILK SCREEN – 8209 PCB.......................................................................... 12
APPENDIX D - COMPLIANCE NOTICES............................................................................ 13
FEDERAL COMMUNICATIONS COMMISSION STATEMENT ........................................................... 13
WARRANTY............................................................................................................................... 14
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 1 - SEALINKDIO-16UserManual
Introduction
The SeaLINK DIO-16 provides 8 Reed relays that can latch power, data or other
electronic signals for control applications and 8 optically isolated inputs to allow
monitoring of off board switch closures, relays or for any other general purpose
monitoring needs. The adapter is USB 1.1 compliant.
The SEALINK DIO-16 is designed to be used under Windows 98/ME/2000/XP. The
SeaI/O API (Application Programmer Interface) included on CD with the SEALINK
DIO-16 provides a variety of useful high-level function calls implemented in a
Windows dynamic link library (DLL). This API gives access to the SeaLINK DIO-
16 I/O from Windows-based platforms such as Visual C++. In addition to the API,
SeaI/O includes an ActiveX control along with sample code and utilities to simplify
software development.
Other Sealevel USB Digital I/O Products
SeaLINK PLC-16 (P/N 8206) - 8 Form C Relays/8 Opto-isolated Inputs
SeaLINK ISO-16 (P/N 8207) - 16 Opto-isolated Inputs
SeaLINK REL-16 (P/N 8208) - 16 Reed Relay Outputs
SeaLINK PIO-48 (P/N 8203) - 48 TTL Inputs/Outputs
SeaLINK PIO-96 (P/N 8205) - 96 TTL Inputs/Outputs
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 2 - SEALINKDIO-16UserManual
Before You Get Started
What’s Included
The SEALINK DIO-16 is shipped with the following items. If any of these items is
missing or damaged please contact Sealevel for replacement.
 SEALINK DIO-16 Adapter
 USB A to B Cable, Part number CA179
 Sealevel SeaI/O Software CD
Optional Items Depending upon your application, you are likely to find one or more of the
following items useful for interfacing the SEALINK DIO-16 to real-world signals.
All items can be purchased from our website (http://www.sealevel.com) or by
calling [phone].
 DIN Rail Clips (Part Number DR102)
− A pair of brackets, clips, and hardware necessary for DIN rail
mounting the SeaLINK DIO-16.
 2U 19” Rack Tray (Part Number RK2U)
− Standard 2U rack tray for supporting SeaLINK and other devices.
 Clamp for Rack Tray (Part Number RK-CLAMP)
− Metal clamp and necessary hardware to secure SeaLINK or other
devices to the RK2U rack tray.
 High Speed USB 2.0 4-Port Hub (Part Number HUB4)
− AC powered 4-port USB hub, AC adapter, and USB cable.
 High Speed USB 2.0 7-Port Hub (Part Number HUB7)
− AC powered 7-port USB hub, AC adapter, and USB cable.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 3 - SEALINKDIO-16UserManual
Software Installation
Windows 98/ME/2000/XP Installation
Important: Do not connect the SeaLINK DIO-16 adapter to the host USB
device until the software has been fully installed.
1. Start Windows.
2. Insert the Sealevel Systems CD in to your CD drive.
3. If ‘Auto-Start’ is enabled for this drive the software will automatically
launch. Otherwise, point your browser to the ‘Index.htm’ on the root
directory of the CD
4. Select ‘Install Software’.
5. Select the Part Number for your adapter from the listing.
6. Select ‘Windows 98/ME/2000/XP’. The setup file will automatically detect
the operating environment and install the proper components. Next
(depending on your browser) select the ‘Run this program from its current
location’ or ‘Open’ option. Follow the information presented on the screens
that follow.
7. A screen may appear with the declaration: “The publisher cannot be
determined due to the problems below: Authenticode signature not found.”
Please select the ‘Yes’ button and proceed with the installation. This
declaration simply means that the Operating System is not aware of the
driver being loaded. It will not cause any harm to your system.
8. During setup the user may specify installation directories and other preferred
configurations. This program also adds entries to the system registry that are
necessary for specifying the operating parameters for each driver. An
uninstall option is also included to remove all registry/INI file entries from
the system.
Windows NT Note: Windows NT is not USB aware and thus cannot support the
SeaLINK DIO-16.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 4 - SEALINKDIO-16UserManual
Physical Installation
The SeaLINK DIO-16 can be installed in any open USB port.
Do not plug the unit into a USB port until the software has been fully installed.
1. Simply connect the SeaLINK DIO-16 to your USB port with the supplied
cable.
2. The software drivers installed during setup will automatically recognize and
configure the device.
3. You should see one or more “New Hardware Found” windows, indicating
the actual device being created.
4. Next, view your system’s Device Manager.
5. You should have a new ‘SeaIO 8209’ in the SeaI/O Device heading
indicating the installation was successful.
The SEALINK DIO-16 is now ready for use.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 5 - SEALINKDIO-16UserManual
Programming the SEALINK DIO-16
Sealevel’s SeaI/O software is provided to assist in the development of reliable
applications for the Sealevel Systems family of digital I/O adapters. Included on the
SeaI/O CD are driver functions for use in accessing the I/O as well as helpful
samples and utilities.
Programming for Windows
The SeaI/O API (Application Programmer Interface) provides a variety of useful
high-level function calls implemented in a Windows dynamic link library (DLL).
The API is defined in the help file (Start/Programs/SeaIO/SeaIO Help) under
“Application Programmers Interface”. This help file also includes detailed
information dealing with installation / removal of the software and information
about latency, logic states, and device configuration.
For C language programmers we recommend using the API to access the SEALINK
DIO-16. If you are programming in Visual Basic, using the ActiveX control
included with SeaI/O is advised.
Samples and Utilities
A variety of sample programs and utilities (both executable and source code) are
included with SeaI/O. Further documentation on these samples can be found by
selecting “Start/Programs/SeaIO/Sample Application Description”. Information
about where the files are physically stored on your disk is also included in this same
file.
Digital I/O Interface
The SeaLINK DIO-16 provides one parallel input port and one parallel reed relay
output port. The ports are organized as ports A, and B. Port A is an input port
interfaced to optically isolated inputs, while port B is the relay output port. The
SeaLINK DIO-16 is a line-powered device requiring a USB port capable of sourcing
500 mA.
Serial String Each device has an eight digit alphanumeric serial string stored in non-volatile
memory. On the Windows platforms, this number is used to give each unit a
separate identity. This identity allows the device to be moved to any USB port or
hub port on your computer while retaining its device number. If a device becomes
damaged and is replaced the new device should be given the same serial string as the
device it is replacing. This string is stored in an EEPROM along with other critical
information. This EEPROM is read during enumeration. The device should not be
unplugged during its enumeration due to remote possibility that the data in the
EEPROM could be corrupted if power is removed during a read/write cycle to the
EEPROM. Enumeration is complete when the LED is lit.
The control panel utility provides the capability to read or modify this string.
However, setting the same string for two units connected to the same computer will
cause the second unit to fail enumeration, and make it invisible to the operating
system. Should this occur, unplug one unit and set the serial string for the other unit
to a different string.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 6 - SEALINKDIO-16UserManual
Input Port Port A is an eight bit input port connected to optically isolated input sensors. Each
sensor can be used to interface a voltage input and then sense whether the voltage is
on or off. Each sensor is isolated (with respect to a common ground) from every
other sensor, and also isolated with respect to the host PC ground. This means that
signals such as low-level AC line voltage, motor servo voltage, and control relay
signals can be ‘sensed’, or read by the PC, without the risk of damage due to ground
loops or ground faults.
Each sensor input pair has a current limiting resistor (2.7K ohm) that is used to limit
the input current to the opto-isolator. The opto-isolator has two ‘back-to-back’
diodes internally. This allows AC or DC signals to be sensed, regardless of polarity.
When the applied voltage is high enough to cause the led in the opto-isolator to turn-
on, the output of the opto-isolator goes low (0 volts) and the signal is read as a low
logic level (binary 0) by the PC. When the input signal is too low to turn on the
opto-isolator, the output goes high and the port bit is read by the PC as a high logic
level (binary 1).
The opto-isolator requires approximately 1mA to turn on. The maximum input
current is 50mA. There are two things to consider when selecting the input resistor.
The first is turn on voltage for the circuit to sense, and second is the maximum input
voltage. Maximum input voltage must not provide too much power to the input
resistor, and must also not overdrive the opto-isolator input current specification.
The following formulas apply:
Turn on Voltage = diode drop + (turn on current) x (resistance) [Ex: 1.1 + (.003) x R]
Input Current = ((input voltage)-1.1V) / (resistor value)
Maximum voltage = 1.1 + square root of (.25(resistor value))
The following table shows the ranges associated with the resistor.
Input Resistor Turn-On Input Range Max Input Max Current
2.7KΩ3.0V 5 – 30V 37V 13mA
Note: The turn-off voltage for all resistors is less than 1V.
Because through hole resistors are utilized, they cannot be easily replaced. If
modification is necessary, Sealevel can do this for an additional charge.
Important: The input circuits are not intended for monitoring 120-volt AC circuits.
In addition to being too high a voltage for the circuits, it is dangerous to have that
high a voltage on the card.
Output Ports (Reed Relays)
Reed relays provide very high quality, long life, low power, dry contact switch
closures. Reed relays are not suited for high current applications, or inductive loads.
The relays are normally open, and close when energized. Writing a logic value of
one or zero will change the state. Refer to the Application Programmers Interface for
more information.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 7 - SEALINKDIO-16UserManual
Pin Assignments (Removable Terminal Block)
Port A (Input) Bit Port A Terminals
0 0,1
1 2,3
2 4,5
3 6,7
4 8,9
5 10,11
6 12,13
7 14,15
Port B (Output)
Bit Port B Terminals
0 0,1
1 2,3
2 4,5
3 6,7
4 8,9
5 10,11
6 12,13
7 14,15
Side Panel View Port A
76543210Port : A
E
Side Panel View Port B
76543210Port : B
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 8 - SEALINKDIO-16UserManual
Electrical Characteristics
Features
 8 SPST Reed relays
 Eight optically isolated inputs
 Removable screw terminals
 Powered by USB port
Specifications Input Ports
 Turn On Current: 1mA
 Isolator Diode Drop: 1.1 VDC
 Resistor Power Max: .5 W
 Maximum Input Range: 5 – 30 VDC/VAC
Output Relays
 Contact Max Power Rating: 10 W
 Contact Voltage Maximum: 100 VDC/VAC
 Contact Current Maximum: .5 A AC/DC RMS
 Contact Resistance, Initial: .15 Ω
 Rated Life:
• Low Load: 200 Million Closures
• Maximum Load: 100 Million Closures
 Contact Speed:
• Operate: .5 mS
• Release: .5 mS
• Bounce: .5 mS
 Maximum Operating Speed: 600 Hz
Temperature Range
 Operating: 0°C – 70°C
 Storage: -50°C – 105°C
Power Requirements
 +5VDC @ 500mA
Manufacturing
All Sealevel Systems Printed Circuit boards are built to UL 94V0 rating and are
100% electrically tested. These printed circuit boards are solder mask over bare
copper or solder mask over tin nickel.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 9 - SEALINKDIO-16UserManual
Example Circuits
Input Circuit
Output Circuit
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 10 - SEALINKDIO-16UserManual
Appendix A - Troubleshooting
Following these simple steps can eliminate most common problems.
1. Install software first. After installing the software then proceed to adding the
hardware. This places the required installation files in the correct locations.
2. Read this manual thoroughly before attempting to install the adapter in your
system.
3. Use Device Manager under Windows to verify proper installation.
4. Use the SeaIO Control Panel applet or the Device Manager’s property page for
card identification and configuration.
5. If these steps do not solve your problem, please call Sealevel Systems’ Technical
Support, [phone]. Our technical support is free and available from
8:00AM-5:00PM Eastern Time Monday through Friday. For email support
contact [email protected].
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 11 - SEALINKDIO-16UserManual
Appendix B - How To Get Assistance
Begin by reading through the Trouble Shooting Guide in Appendix A. If assistance
is still needed please see below.
When calling for technical assistance, please have your user manual and current
adapter settings. If possible, please have the adapter installed in a computer ready to
run diagnostics.
Sealevel Systems provides an FAQ section on its web site. Please refer to this to
answer many common questions. This section can be found at
http://www.sealevel.com/faq.asp
Sealevel Systems maintains a Home page on the Internet. Our home page address is
http://www.sealevel.com. The latest software updates, and newest manuals are
available via our FTP site that can be accessed from our home page.
Technical support is available Monday to Friday from 8:00 a.m. to 5:00 p.m. eastern
time. Technical support can be reached at [phone].
RETURN AUTHORIZATION MUST BE OBTAINED FROM SEALEVEL
SYSTEMS BEFORE RETURNED MERCHANDISE WILL BE ACCEPTED.
AUTHORIZATION CAN BE OBTAINED BY CALLING SEALEVEL
SYSTEMS AND REQUESTING A RETURN MERCHANDISE
AUTHORIZATION (RMA) NUMBER.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 12 - SEALINKDIO-16UserManual
Appendix C – Silk Screen – 8209 PCB
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 13 - SEALINKDIO-16UserManual
Appendix D - Compliance Notices
Federal Communications Commission Statement
FCC - This equipment has been tested and found to comply with the limits for Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in such case the user will be required to correct the interference at the
users expense.
EMC Directive Statement
Products bearing the CE Label fulfill the requirements of the EMC directive
(89/336/EEC) and of the low-voltage directive (73/23/EEC) issued by the European
Commission.
To obey these directives, the following European standards must be met:
EN55022 Class A - “Limits and methods of measurement of radio interference
characteristics of information technology equipment”
EN55024 – “Information technology equipment Immunity characteristics Limits and
methods of measurement”.
EN60950 (IEC950) - “Safety of information technology equipment, including
electrical business equipment”
Warning
This is a Class A Product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures to prevent or correct the interference.
Always use cabling provided with this product if possible. If no cable is provided or
if an alternate cable is required, use high quality shielded cabling to maintain
compliance with FCC/EMC directives.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© Sealevel Systems, Inc. - 14 - SEALINKDIO-16UserManual
Warranty
Sealevel's commitment to providing the best I/O solutions is reflected in the Lifetime
Warranty that is standard on all Sealevel manufactured products. We are able to
offer this warranty due to our control of manufacturing quality and the historically
high reliability of our products in the field. Sealevel products are designed and
manufactured at its Liberty, South Carolina facility, allowing direct control over
product development, production, burn-in and testing.
Sealevel Systems, Inc. (hereafter "Sealevel") warrants that the Product shall conform
to and perform in accordance with published technical specifications and shall be
free of defects in materials and workmanship for life. In the event of failure,
Sealevel will repair or replace the product at Sealevel's sole discretion. Failures
resulting from misapplication or misuse of the Product, failure to adhere to any
specifications or instructions, or failure resulting from neglect or abuse are not
covered under this warranty.
Warranty service is obtained by delivering the Product to Sealevel and providing
proof of purchase. Return authorization must be obtained from Sealevel Systems
before returned merchandise will be accepted. Authorization is obtained by
calling Sealevel Systems and requesting a Return Merchandise Authorization
(RMA) number. The Customer agrees to insure the Product or assume the risk of
loss or damage in transit, to prepay shipping charges to Sealevel, and to use the
original shipping container or equivalent. Warranty is valid only for original
purchaser and is not transferable.
Sealevel Systems assumes no liability for any damages, lost profits, lost savings or
any other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Sealevel Systems will not be liable for any claim made
by any other related party.
This warranty applies to Sealevel manufactured Product. Product purchased through
Sealevel but manufactured by a third party will retain the original manufacturer's
warranty.
Sealevel Systems, Incorporated
2779 Greenville Highway
P.O. Box 830
Liberty, SC 24857 USA
[phone] FAX: [phone]
www.sealevel.com
email: [email protected]
Technical Support is available Monday - Friday from 8 a.m. to 5 p.m. Eastern time
Trademarks Sealevel Systems, Incorporated acknowledges that all trademarks referenced in this
manual are the service mark, trademark, or registered trademark of the respective
company.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Artisan Technology Group is an independent supplier of quality pre-owned equipment
Gold-standard solutions
Extend the life of your critical industrial,
commercial, and military systems
with our
superior service and support.
We buy equipment
Planning to upgrade your current
equipment? Have surplus equipment taking
up shelf space? We'll give it a
new home.
Learn more!
Visit us at artisantg.com for more info
on price quotes, drivers, technical
specifications, manuals, and documentation.
Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein.
We're here to make your life easier. How can we help you today?
[phone] [e-mail] Iartisantg.com